Frymaster GF14 Gas Fryers Instruction Manual

: September 25, 2024
: FRYMASTER

Table of Contents

GF14 Gas Fryers
Product Information
Specifications:
Product Usage Instructions:
High Altitude Orifice Kit Installation:
- FAQs (Frequently Asked Questions):
Q: Can I install the orifice kit myself?
Q: How do I check for gas leaks after installation?
Q: What should I do if I encounter difficulties during

GF14 Gas Fryers

“`html

Product Information

Specifications:

Manufacturer: Frymaster Dean
Address: 8700 Line Avenue, Shreveport, LA 71106
Contact: 318-865-1711, 800-551-8633
Website: www.frymaster.com
Email: fryservice@welbilt.com
Models Affected: GF14, GF40 Gas Fryers

Product Usage Instructions:

High Altitude Orifice Kit Installation:

Ensure the gas supply is shut off before proceeding with any
work.
Disconnect the fryer from both the gas and electrical power
supply.
Drain the frypot or remove the drain handle.
Disconnect wires from the gas valve terminal block, marking
each wire for easy reconnection.
Remove the burner assembly carefully.
Install the new orifice kit following the provided chart for
altitude and gas type specifications.
Reinstall the burner assembly ensuring proper alignment and
spacing.
Check gas pressure and connections for leaks using a soapy
water solution.
Light the pilot following the Installation and Operation
Manual.

FAQs (Frequently Asked Questions):

Q: Can I install the orifice kit myself?

A: No, the orifice kit must be installed by a Factory Authorized
Servicer to avoid impacting the product warranty. Contact
1-800-551-8633 or your local Factory Authorized Servicer for
installation.

Q: How do I check for gas leaks after installation?

A: Apply a solution of soapy water to each connection in the gas
supply system and check for bubbles. If bubbles appear, there is a
leak that needs to be addressed.

Q: What should I do if I encounter difficulties during

installation?

A: If you face any challenges during installation, contact a
professional technician or the manufacturer’s customer service for
assistance. Do not attempt to force any components together as it
may cause damage.

“`

Instruction Sheet

FRYMASTER DEAN 8700 LINE AVENUE, SHREVEPORT, LA 71106
318-865-1711 800-551-8633 WWW.FRYMASTER.COM EMAIL: FRYSERVICE@WELBILT.COM
Subject: High Altitude Orifice Kit Instructions
Models affected: GF14, GF40 Gas Fryers

The orifice kit MUST be installed by a Factory Authorized Servicer. Failure to use a Factory Authorized Servicer could impact the product warranty. Call 1-800-551-8633 or your local Factory Authorized Servicer to schedule installation of the kit.

Follow these instructions to replace the orifices.

Use the chart below to ensure that the correct kit and orifice size is installed for the type of fryer, gas and altitude.

ALTITUDE
2000’3999′
4000’5999′

GF14 NAT Kit # 8263809 1.60MM #52
Kit # 8263813 1.55MM #53

GF14 LP
Kit # 8263810 1.02MM #60
Kit # 8263814 .99MM #61

GF40 NAT Kit # 8263811 1.40MM #54
Kit # 8263815 1.36MM #55

GF40 LP
Kit # 8263812 .82MM #66
Kit # 8263816 .81MM #67

CAUTION
The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.

Installation Instructions
1. Shut off the gas supply to the fryer and disconnect the fryer from the gas and electrical power supply. 2. Drain the frypot or disconnect and remove the drain handle.
WARNING Drain the frypot or remove the handle from the drain valve before proceeding further.
3. Disconnect the wires from the gas valve terminal block, marking each wire to facilitate reconnection. 4. Disconnect the pipe union collar at the right side of the gas valve. 5. On GF40 fryers, remove the burner heat shield hanger screws at the front of the burner and remove
the heat shield.

8198049
Document Number: FRY_INST_8198049 05/2024 1 of 2

6. Remove the burner hanger screws and lower the front of the burner assembly. Pull it forward to clear the rear burner hanger, then lower the burner to the floor of the cabinet. Carefully pull the burner assembly from the cabinet.
7. Use a ½-inch box end wrench to remove the brass orifice(s) that holds the deflector to the burner manifold. Position the new deflector and reinstall the orifice(s).
WARNING Use extreme care to prevent cross-threading and stripping when reinstalling the brass
orifices.
8. Reverse steps 1-6 to reinstall the burner assembly. Check spacing and alignment of targets in accordance with the next steps.
9. GF40 – Proper spacing of the edge of the deflectors is ¾-inch (19mm) from the frypot side. To adjust target spacing, bend the brackets to which they are attached away or toward the frypot to the proper distance. (A board of the proper thickness is useful as a gauge to verify spacing and alignment.) The illustration below depicts a typical GF40. GF14 – Targets are vertical and parallel front to rear.
¾-inch (19mm) gap between deflectors and frypot.
GF40 Illustration
10. Remove the cap screw covering the pressure regulator spring of the gas valve. 11. Verify that the incoming gas pressure is in accordance with the appropriate table in the Installation
and Operation Manual for the fryer being converted. 12. Open the gas supply to the fryer and check for leaks using a solution of soapy water applied to each
connection in the fryer’s gas supply system. 13. Attach a manometer to the burner manifold pressure tap then reconnect the fryer to the electrical
power supply. 14. Light the pilot in accordance with the instructions in the Installation and Operation Manual for the
fryer being converted and verify that the pilot flame is approximately 1-inch long. If adjustment is necessary, remove the pilot flame adjustment screw cap and, using a small flat-tipped screwdriver, turn the adjustment screw counterclockwise to increase the length of the flame or clockwise to decrease it. Reinstall the cap when adjustments are completed. 15. Verify that there is cooking oil or water in the frypot. Place the gas valve in the ON position to light the burner. Verify that the burner lights all the way around and that the manifold pressure is in accordance with the rating place. Adjust the burner manifold pressure as required by turning the
2 of 3 Document Number: FRY_INST_8198049 05/2024

regulator adjustment screw clockwise to increase the pressure or counterclockwise to reduce the pressure. 16. When the pressure has been verified as correct, shut down the fryer and install the cap screw furnished with the kit over the regulator adjustment screw. 17. Shut off the gas supply to the fryer, disconnect the manometer, and reinstall the pressure tap plug. Use a solution of soapy water to verify the plug is not leaking. 18. Open the gas supply and light the burner. Verify proper operation of the fryer in accordance with the instructions in the Installation and Operation Manual.
Typical Burner Manifold Assembly
The assembly illustrated is typical of the burner manifold assemblies for which these kits are designed. It is representative in nature and is intended to identify the various components to be adjusted or replaced. The actual assembly may differ slightly in ap pea ranc e.
The size of the burner orifice in MM is stamped on top of the orifice.
Burner Orifices Number varies by fryer type

Burner manifold pressure test tap.

The regulator adjustment screw and spring are located beneath this cap.

The pilot flame adjustment screw is located beneath this cap.

The regulator adjustment screw and spring are located beneath this cap.

The pilot flame adjustment screw is located beneath this cap.

Honeywell

Robertshaw
3 of 3 Document Number: FRY_INST_8198049 05/2024