eeese 2502 Emil Dehumidifier User Manual
- September 20, 2024
- eeese
Table of Contents
- eeese 2502 Emil Dehumidifier
- Product Usage Instructions
- Safety Instructions
- Power Cord
- Parts List
- Prior to Operation
- Continuous Drainage
- Operation Instructions
- Cleaning
- Storage
- Display Error Codes
- Trouble Shooting
- Technical Specifications
- Smart Connection Operation Guide
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
eeese 2502 Emil Dehumidifier
Specifications
- Model: Emil
- Art. Numbers: 2502 & 2508
- Manufacturer: eeesse air care
- Email: info@eeese-aircare.com
- Website: eeese-aircare.com
Product Usage Instructions
Safety Instructions
Warning: This dehumidifier is intended for domestic use only to avoid
fire, electrical shocks, or other hazards.
Power Cord Placement
- Do not wet hands while handling the power cord.
- Avoid placing heavy objects on the power cord to prevent safety hazards.
- Do not pull the power cord to unplug the device; contact authorized service center for any repairs.
Prior to Operation
Before using the dehumidifier, ensure you have read the user manual
thoroughly.
Frequently Asked Questions (FAQ)
Q: Can this dehumidifier be used in commercial environments?
A: No, this dehumidifier is designed for domestic use only.
Using it in commercial environments may pose risks.
User manual
Dehumidifier Emil
Art. 2502 & 2508
Thank you for choosing this product.
Please read this instruction manual before using it.
Read the user manual before any use, refer to the corresponding section in
this user manual.
Recycle unwanted materials instead of disposing of them. All appliances and
packaging should be sorted and tendered at a regional recycling centre and be
processed in an ecological manner.
The product conforms to the applicable European and other directives.
Safety Instructions
Warning
This appliance is intended for use in a domestic environment only. Any other
use is not recommended by the manufacturer and may cause fire, electrical
shocks or other person injury and property damage.
Power Cord
During Use
Parts List
Components
-
Front cover
-
Top cover
-
Control board
-
Air outlet
-
Cupped lift
-
Air inlet filter
-
Water tank
-
Rear cover
-
Drainage outlet
-
Power cord Control panel
-
Power button
-
Timer button
-
Humidity controlbutton
-
Fan speed button/
Child lock button -
Clothes drying button
-
WiFi (only 2502)
-
Clothes drying light
-
High speed light
-
Low speed light
-
Humidity Reading Display
-
Timer light
-
Tank full light
-
Defrost light
-
Running light
Drainage -
Drainage outlet
-
Drainage hose (not included)
Prior to Operation
- Place the dehumidifier in an upright position on a stable, flat surface.
- Ensure the dehumidifier is at a safe distance at least 50 cm away from a wall or furni-ture.
- Supply power should be in correspondence with the value on the nameplate, power outlet needs to be grounded.
- Ensure the tank is correctly fitted, if the tank is full or not in place, the “tank full” light comes on and the dehumidifier will stop working.
- Turn on the power and run the machine as per instructions below.
Continuous Drainage
In general, water will be collected by tank, if you want continuous drainage, please do steps as follows:
- Remove the water tank.
- Push a 14mm interval diameter hose on to the spout.
- Put the water tank back in place.
Operation Instructions
Switch On / Switch Off The Unit [ Power button ]
- Connect to the power supply and press the power button once to turn on the unit.
- By default mode the unit runs on manual continuous dehumidifying with high fan speed. The on/off indicator will be on.
- Press the power button to turn off the unit, it will stop working, fan will work for some seconds to blow out the hot air inside the unit.
- When the machine is in standby mode, the on/off inicator will flash slowly.
Auto Shut-off Timer Function [ Timer button ]
- Press the timer button to select your preferred timer hour from 00-24-00 for automatic shut off setting by each press.
- Auto timer off setting will be cancelled if the timer button is pressed 2 times in 5 seconds.
- Auto timer off setting will be cancelled if the unit is switched off and switch on again. ****
Humidity Setting [ Up and Down buttons ]
- Press the humidity setting buttons to select your preferred humidity from CO-30%-35%-40%-45%-50%-55%-60%-65%-70%-75%-80%-CO. CO means continuous dehumidifying regardless of ambient humidity.
- When the humidity in the room falls below the set value, the dehumidifier automatically turns off. The dehumidifier automatically restarts when the humidity exceeds the set value.
- The dehumidifier is less effective in cold rooms because it utilizes the heat in the air to dehumidify.
Fan Speed Option [ Fan Speed button ]
- Press the fan speed button to select your preferred fan speed setting of low and high to meet the different usage requirements.
- Fan speed button is invalid at Laundry drying mode and Defrost mode.
Laundry Drying Function [ Laundry Drying button ]
Press the laundry drying button to activate Laundry Drying function, the unit
runs in con-tinuous dehumidification with high fan speed for 6 hours then
switch off automatically.
Fan speed button and timer button are invalid.
WiFi Function [ Timer button-2 seconds] (only 2502)
Press the Timer button for 2s to activate WiFi function and enter the
distribution network mode, during the network configuration, the WiFi
indicator flash quickly, after WiFi connec-ted the indicator is on.
Detailed operation, please refer to the manual ”Smart Connection Operation
Guide”.
Safety Childlock Function [ Fan Speed button-2 seconds ]
Press the Fan speed button for 2s to lock all buttons with a beeping sound,
the same operation can unlock it.
Safety childlock function can be set at standby mode and working mode but
can’t be activated when water tank is full.
Low Temperature Defrost Indicator
When the ambient temperature is too low, the dehumidifier will enter into
defrost mode, the unit runs with high fan speed without dehumidifying.
Auto Shut off with Water Tank Full Indicator
The unit will enter into standby mode when the water tank is full or when
the water tank is not installed properly. After emptying the tank, or
installing the water tank properly, the unit will go on to the previous mode.
Except for the power button, all other buttons are invalid.
Memory Function
- When unplugged directly or power is cut, then reconnect to the power supply, the dehumidifier will run with the mode prior to the shutdown. The timer setting will be kept.
- Press the power button to switch off the dehumidifier, and then press the power button to switch it back on. The dehumidifier will run with the mode prior to the shutdown. The timer setting will be cancelled.
- Switch off the dehumidifier and unplug the power cord, then reconnect the power supply and switch on the dehumidifier. It will run in factory preset mode.
Cleaning
When used regularly, the filter may become clogged with dust and particles. Therefore the filter should be cleaned at least every two weeks. Follow these steps:
- Switch the device off and remove the plug from the socket before cleaning.
- Clean the housing with soft, dry cloth. If the device is ex-tremely dirty, use a mild cleaning agent. Wipe the dehumidi-fier with a slightly damp cloth. Never spray the device with water.
- Remove the grate, clean the grate with a vacuum cleaner or soapy water no hotter than 40°C.
- Rinse and dry the grate completely before installing back to the device.
Storage
If the dehumidifier will not be used for a long period of time, take the following steps:
- Remove the plug from the socket and empty the tank, make sure the tank and the dehumidifier is completely dry. This may take a couple of days.
- Clean the air filter.
- Check the dehumidifier for perfect condition to ensure a safe use of it after a long period of storage.
- Pack the device with the suitable packaging.
- Store the dehumidifier in a dust-free location, and out of direct sunlight. Preferably covered with a sheet of plastic.
Display Error Codes
Please contact your local distributor if any of the error codes below appears.
Code | Error | Display | What is happening |
---|---|---|---|
E1 | Temperature sensor error | Flash every 30 seconds | Device still |
dehumidifies but is in defrost mode only.
E2|
Humidity sensor error
| Flash every 30 seconds| Device still dehumidifies but is in continuous
dehumidifying mode only.
3| ir inlet temperature is too high >42ºC| lowly flash L3| Compressor stop
working, fan works at low fan speed. 10mins later, if the temperature decrea-
se to below 40 machine will work normally.
L4| Air inlet temperature is too low >0ºC| Slowly flash L4| Compressor stop
working, fan works at low fan speed. 10mins later, if the temperature increase
to above 2 machine will work normally.
Trouble Shooting
Check the following before contacting technical support .
PROBLEM | POSSIBLE CAUSE | SOLUTION |
---|---|---|
The device does not work | The power is not connected | Insert the plug into the |
wall outlet
The water tank is full| Empty the tank
The tank has not been replaced correctly| Replace the tank
Water removal ca- pacity is too low| Runtime is too short| Be patient and wait
Ambient temperature or humidi- ty is too low| It is normal that the device
does not dehumidify in these conditions
The device works, but reduces the relative humidity insufficiently| The room
is too big| We recommend using a dehu- midifier with a greater capacity
There is too much ventilation| Reduce ventilation (e.g. close windows and shut
doors)
The air filter is clogged| Clean the air filter
Set humidity is higher than the ambient humidity| Set the humidity lower than
ambient humidity
Dehumidifier is blowing out warm air| The dried air is passed over heating
coils before it is blown into the room as part of the dehumidifying process|
This is normal, a dehumidifier is not an air cooler
---|---|---
The display is not showing the hu- midity set point| The display shows the
room rel- ative humidity not the set point| Press the humidity control button
once to see the target relative humidity
Water on floor| There is residual water in tank, and the device is lurched too
much by moving| Be careful when moving the tank
The dehumidifier is noisy| The air filter is blocked or the device is on an
uneven surface| Clean the filter or put the de- vice on a flat surface
Technical Specifications
Model Emil Art. no | 2508 | 2502 |
---|---|---|
Max. working area m2 | 40 | 50 |
Timer, h | 1 ~ 24 | |
Power Supply | 220-240V – 50Hz | |
Dehumidifying Capacity, L/day (30°C RH 80%) | 10 | 12 |
Dehumidifying Capacity, L/day (27°C RH 60%) | 6.5 | 7.5 |
Power Consumption, W | 165 | |
Air Volume m3/h | High | 105 |
Low | 80 | |
Noise Level dB(A) | High | 40 |
Low | 36 | |
Water Tank Capacity, L | 2.6 | |
Operating Temperature, °C | 5~35 | |
Refrigerant | R290 | |
Compressor | Piston | |
Net Weight, kg | 10,1 | 10,4 |
Filter | Washable | |
WiFi | No | Yes |
Drain Hose Diameter mm | 14 | |
Drain hose included (Art. 2558) | No | |
Length of cable, cm | 190 | |
Product Size (WDH), mm | 300 × 250 × 463 |
The above technical data are for reference only. We reserve the right to modify them without notice.
Smart Connection Operation Guide
APP Binding Device
Search an APP platform for “TuyaSmart” or scan the following QR code to
download the APP.
-
Step One
Make sure the phone is connected to the WIFI at home, and turn on the Bluetooth device, tap the upper right corner of the home page + to add device. -
Step Two
Follow the instructions to select the device to be configured, and then enter the password for the wireless network which should be on 2.4 GHz. -
Step Three
Complete the connection to set the dehumidifier with APP
Adding Device Manually
-
Step One
Tap Add Device on the home page or + in the upper right corner to go to the Add Device page. -
Step Two
Confirm the indicator rapidly blink and enter the WiFi password. -
Step Three
Complete the connection to set the dehumidifier with APP
Service
If you need service or to make a warranty claim, you must create a case
directly in our support system. Go to the website under SUPPORT. <https
://eeese-aircare.com/support>
Warranty
Limited warranty
-
We guarantee that all parts are free of defects in materials and workmanship for a period of two years from the date of purchase. The warranty covers only material or manufacturing defects that prevent the product from being able to be installed or operated in a
normal way. Defective parts will be replaced or repaired. -
The warranty does not cover transportation damage, any use other than what is intended, damage caused by incorrect assembly or improper use, damage caused by impact or other error, or by improper storage.
-
The warranty becomes void if the user modifies the product.
-
The warranty does not include product-related damage, property damage or general operational loss.
-
The manufacturer’s liability cannot exceed the repair or replacement of defective parts and does not include labour costs to remove and reinstall the defective part, transport tion costs to and from the service center, and all other materials necessary to carry ou the repair.
This warranty does not cover failure or malfunction as a result of the
following:
- Lack of proper installation, operation or maintenance of the unit in accordance with our published “User’s Guide” supplied with the unit.
- The workmanship of any installation of the unit.
- Misuse, alteration, accident, fire, flood, lightning strike, rodents, insects, negligence or unforeseen events.
- Use of non-factory authorised parts or accessories in conjunction with the product.
Limitation of liability
This is the only warranty provided by the manufacturer. No one is authorised
to make any other warranties on our behalf.
This warranty is in lieu of all other warranties, expressed or implied,
including but not limited to any implied warranty of fitness for a particular
purpose and saleability. We expressly disclaim all liability for consequential
damage, accidental damage, indirect loss or loss related to a breach of the
expressed or implied warranty.
This warranty gives you specific legal rights, which may vary by country. Complaints In the event of any warranty claim a valid purchase receipt must be presented. Read about raising a warranty-claim under the SERVICE section.
IMPORTANT!
If you need technical help – contact our customer service: https://eeese-
aircare.com/support
We have specialist knowledge of our products and the field in general, so you
can get help quickly and easily
Thank you for choosing this product.
Please read this instruction manual before using it eeese air care . info
@eeese-aircare.com
Web: eeese-aircare.com . MV-2502-2509-03-2024
MIX
Stetter ansvarligt skovbrug Supporting responsible forestry FSC® C168135
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>