SOLIGHT WO68-W 3 In 1 LED Rechargeable Lamp Owner’s Manual
- September 20, 2024
- Solight
Table of Contents
SOLIGHT WO68-W 3 In 1 LED Rechargeable Lamp
Specifications :
- Power input: 4W max.
- Luminous flux: 280lm
- Chromaticity: 3000K, 4000K, 6500K
- Batteries: Li-Ion 18650, 3.7V 2000mAh
- Battery endurance: approx. 3.5h at 100% power
- Battery power supply time: about 3 hours
- Power supply: DC 5V; 1A (cable included, adapter not included)
- Max. dimension: approx. 320 x 120 x 140mm
Product Usage Instructions
Control:
- Fully charge the device before use.
- To switch On, press the touch button on the lamp head.
- Short press: On/Off, change chromaticity.
- Long press: Adjust the intensity of the light.
Installation:
On the table:
- Assemble the base and rod with the supplied screw and tighten with a screwdriver.
- Place the luminaire body on the rod using the magnet and orient it as required.
On the wall – by gluing:
- Clean the surface you are going to glue on.
- Remove the cover on one side of the double-sided tape and stick it to the surface.
- Hold the tape in place for at least one minute and then allow to dry for at least 24 hours.
- After 24 hours, peel off the front side of the double-sided tape cover.
- Glue the luminaire bracket and put the luminaire head on it.
On the wall – by drilling:
- Into the wall:
- Drill holes at the selected location.
- Insert dowels into the drilled holes.
- Screw on the luminaire holder.
- Fit the magnetic head of the luminaire.
- Into the wood:
- Screw on the luminaire holder.
- Fit the luminaire head.
FAQ :
-
Q: Can I use the lamp while charging?
A: It is not recommended to use the lamp while charging as it may reduce the battery’s lifetime. For maximum battery life, charge the light first and then use it. -
Q: How do I know when the lamp is fully charged?
A: The charging LED indicator will show red while charging and green when fully charged.
EN WO68-W, WO68-B LED rechargeable lamp 3in1
Thank you for purchasing our equipment. Please read this manual carefully and heed the safety warnings and instructions before installing, using or repairing the equipment. This will ensure not only the protection of persons, but also the long life of the equipment. USB-C charging cable included. The device can be placed on a table stand, clip or wall bracket (all included). The device can be carried and powered by the built-in battery or used plugged in using the USB cable.
TECHNICAL PARAMETERS
| Power input | 4W |
|---|---|
| Luminous flux | max. 280lm |
| Chromaticity | 3000K, 4000K, 6500K |
| Batteries | Li-Ion 18650, 3.7V 2000mAh |
| Battery endurance | approx. 3,5h at 100% power |
| Battery power supply time | about 3 hours |
| Power supply | DC 5V; 1A (cable included, adapter not included) |
| Max. dimension | approx. 320 x 120 x 140mm |
CONTROL
Fully charge the device before use.
To switch On, press the touch button on the lamp head.
- Short press: On/Off, change chromaticity.
- Long press: Adjust the intensity of the light.
WARNING
- Before use, check that the power cord is not damaged. If damaged, replace it with a cable of the same type.
- The device contains lithium-ion batteries, so avoid contact with fire, water and strong vibrations. Avoid contact with hot surfaces and avoid prolonged exposure to sunlight.
- Leave the power cord disconnected when not in use.
- Do not use the device if any of its parts are damaged!
- Do not repair the equipment. Repairs must only be carried out by the manufacturer’s service centre.
- When lighting and charging at the same time, the battery heats up and reduces its lifetime. For maximum battery life, charge the light first and then use.
DESCRIPTION OF EQUIPMENT
INSTALLATION
On the table
Assemble the base and rod with the supplied screw and tighten with a
screwdriver. Place the luminaire body on the rod using the magnet and orient
it as required.
On the wall – by gluing (A )
- Clean the surface you are going to glue on.
- Remove the cover on one side of the double-sided tape and stick it to the surface.
- Hold the tape in place for at least one minute and then allow to dry for at least 24 hours.
- After 24 hours, peel off the front side of the double-sided tape cover.
- Glue the luminaire bracket and put the luminaire head on it.
On the wall – by drilling (B )
Into the wall:
- Drill holes at the selected location
- Insert dowels into the drilled holes
- Screw on the luminaire holder
- Fit the magnetic head of the luminaire
Into the wood:
- Screw on the luminaire holder
- Fit the luminaire head
The product has been issued with a CE declaration of conformity in accordance
with the applicable regulations.
On request from the manufacturer: info@solight.cz,
or downloadable from www.solight.cz.
Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, Czech Republic.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>