lyyt 153.806UK DIY COB Tape Kit User Manual

September 20, 2024
lyyt

153.806UK DIY COB Tape Kit

“`html

Specifications:

  • Voltage: 24v
  • Power Consumption: 10.5W/m
  • Current: 438 mA/m
  • PSU: 24v 60W 2.5A
  • No of LED’s: 480 per meter
  • Cut interval: 50mm
  • IP Rating: IP20

Product Usage Instructions:

Preparation:

Ensure the surface is clean and dry before fitting the tape.
Connect the power supply and check LED functionality before
installation.

Cutting:

Disconnect from the power supply before cutting. Use sharp
scissors to cut at marked 50mm intervals. Do not discard excess
tape; it can be reconnected.

Fitting:

Clear installation area, remove backing paper, and firmly push
tape onto the surface in 50mm sections for a professional finish.
Cut at marked points when finished. Use a soldering iron to
reattach if needed.

Points to Remember:

  1. Use supplied power adaptor for the kit’s length of tape

  2. Cut only at highlighted 50mm intervals

  3. Avoid connecting multiple reels to a single power supply

  4. Connect the correct wires to ensure tape functionality

  5. Avoid short circuits during soldering

  6. Consider using heat shrink tubing for connection
    protection

  7. Test functionality before final installation

FAQ:

Q: Can I use a different power adaptor with the tape?

A: It is recommended to use the supplied power adaptor to
prevent performance issues.

Q: How should I reconnect cut sections of the tape?

A: Use a soldering iron and solder to connect the DC wire to the
terminals, ensuring no short circuits occur.

Q: What happens if I connect multiple reels to a single power

supply?

A: This can seriously affect performance, so it is advised to
avoid connecting multiple reels to one power supply.

“`

DIY COB Tape Kit

Item ref: 153.806UK / 153.807UK / 153.808UK User Manual

Thank you for purchasing the Lyyt DIY COB Tape Kit. LED tape is ideal for use on the underside of a counter tops, shelves, cupboards, around window frames or in an alcove of a ceiling to name just a few examples.
Before starting, please ensure that you have read this instruction leaflet carefully. If you are unsure about any of the installation details, please consult a professional.
Kit Contents:
· 5m COB LED Tape · UK Power supply · Solder free connector
Preparation
Ensure that the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape. Unravel the tape and connect the power supply. Check that all the LEDs are functioning correctly and if there are any faults return to your retailer without delay.
Cutting
WARNING: Disconnect from the power supply before attempting any cutting.
Measure out each section and cut with sharp scissors at the marked 50mm intervals to achieve the perfect length. Do not discard any excess tape as it can be easily reconnected and used again.

Fitting
Clear the area you wish to install the tape and remove the backing paper, exposing the adhesive. Push tape firmly onto the surface. It is recommended to work on 50mm sections at a time to ensure a professional finish. When you reach the end of your installation cut at the marked cutting point.

You may also reconnect the two pieces either by using the included solder free connector or by soldering the connection points together. The tape has two tracks for the DC voltage with + positive pole at the top and ­ negative pole at the bottom.
To reattach, use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit when making these connections, as this will result in malfunction and possible damage to the power supply.

Points to remember:

  1. Only use the supplied power adaptor for the length of tape in the kit 2) Only cut the tape at the highlighted 50mm intervals. 3) Do not connect another reel and operate from a single power supply as this will seriously affect
    the performance. 4) Ensure you connect the correct wires otherwise the tape will not work. 5) Ensure that when soldering there are no short circuits 6) We recommend use of heat shrink tubing to protect the connection. 7) Check that everything operates correctly before installing.

Specification

Voltage Power Consumption Current PSU No of LED’s Cut interval IP Rating

24v 10.5W/m 438 mA/m 24v 60W 2.5A 480 p/m 50mm IP20

This product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted. Copyright© 2024 AVSL Group Ltd, Unit 2 Bridgewater Park, Taylor Road, Trafford Park, Manchester. M41 7JQ.

AVSL (Europe) Ltd, Unit 3D North Point House, North Point Bus. Park, New Mallow Road, Cork

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals