dji FC8BGC FPV Remote Controller 3 User Guide

dji FC8BGC FPV Remote Controller 3

Overview

1. Power Button
2. Battery Level LEDs
3. Lanyard Attachment
4. C1 Button (Customizable)
5. Control Sticks
6. USB-C Port
7. Control Sticks Storage Slots
8. Flight Pause/RTH Button
9. Gimbal Dial
10. Flight Mode Switch
11. C2 Switch (Customizable)
12. Start/Stop Button
13. Shutter/Record Button

Using for the First Time

1. Charging

2. **Remove the control sticks from the storage slots and mount them on the remote controller.

**

3. Powering On/Off
   • Press the power button once to check the current battery level.
   • Press once then press again and hold for two seconds to power the remote controller on or off.

Linking

Linking the Aircraft and Goggles

1. Press the link button on the goggles. The goggles will start to beep continually.

2. Press and hold the power button on the aircraft until the battery level LEDs start to blink in sequence.

3. Once linking is completed, the battery level LEDs of the aircraft turn solid and display the battery level, the goggles stop beeping.

Linking the Remote Controller and Goggles

1. Press the link button on the goggles. The goggles will start to beep continually.
2. Press and hold the power button of the remote controller until it starts to beep continually and the battery level LEDs blinks in sequence.
3. Once linking is successful, the remote controller stops beeping and both the battery level LEDs on the remote controller and goggles turn solid and display the battery level.

Activation

Make sure all devices are linked after powering on the aircraft, goggles, and the remote controller. Connect the USB-C port of the goggles to the mobile device, run DJI Fly, and follow the prompts to activate. An internet connection is required for activation.

Controlling the Aircraft

The default control stick mode is Mode 2. The left control stick controls the altitude and heading of the aircraft, while the right control stick controls the forward, backward, and sideward movements.

Specifications

Battery Safety Notice

• DO NOT allow liquid to come into contact with the batteries. DO NOT leave batteries covered in moisture or out in the rain. DO NOT drop the batteries into water. Otherwise, an explosion or fire may occur.
• DO NOT use non-DJI batteries. It is recommended to use DJI chargers.
• DO NOT use swollen, leaking, or damaged batteries. In such situations, contact DJI or a DJI authorized dealer.
• The batteries should be used at a temperature between -10° to 40° C (14° to 104° F). High temperatures can cause an explosion or fire. Low temperatures will reduce the performance of a battery.
• DO NOT disassemble or pierce the battery in any way.
• The electrolytes in the battery are highly corrosive. If any electrolytes come into contact with your skin or eyes, immediately wash the affected area with water and seek medical support.
• Keep the batteries out of the reach of children and animals.
• DO NOT use a battery if it is involved in a crash or heavy impact.
• Extinguish any battery fire using water, sand, or a dry powder fire extinguisher.
• DO NOT charge the battery immediately after flight. The battery temperature may be too high and may cause serious damage to the battery. Allow the battery to cool down to close to room temperature before charging. Charge the battery at a temperature range of 5° to 40° C (41° to 104° F). The ideal charging temperature range is 22° to 28° C (72° to 82° F). Charging at the ideal temperature range can prolong battery life.
• DO NOT leave the batteries near heat sources such as a furnace or heater or inside a vehicle on a hot day.
• DO NOT store the battery for an extended period after fully discharging. Otherwise, the battery may over-discharge and cause irreparable damage to the battery cell.
• If a battery with a low power level has been stored for an extended period, the battery will enter deep hibernation mode. Recharge the battery to bring it out of hibernation.

FCC Compliance Statement

Supplier’s Declaration of Conformity

Product name: DJI FPV Remote Controller 3
Model Number: FC8BGC
Responsible Party: DJI Research LLC
Responsible Party Address:17301 Edwards Road, Cerritos, CA 90703
Website: www.dji.com

We, DJI Research LLC, being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

ISED Compliance Notice

CAN ICES-003 (B) / NMB-003(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the RSS-102.

EU & UK Compliance Notice

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI FPV Remote Controller 3) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI FPV Remote Controller 3) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.

A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

References

• DJI - Official Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>