ENGO CONTROLS ECAM-QG-A4 ECAM Smart Camera Instruction Manual
- September 18, 2024
- ENGO CONTROLS
Table of Contents
CAM
ECAM | Smart Camera
Quick Guide
Ver. 1.0 Release date: V 2024
Soft: V2.117.893
Producer: Engo Controls sp. z o.o. sp. k.
Rolna 4 St. 43-262 Kobielice
Poland
Works with Powered By
GET IT ON Available on the
www.engocontrols.com
Technical specification
Power supply
5V DC USB Type C
Communication
Wi-Fi 2.4GHz
Resolution
4Mpx 2560*1440P
Storage
TF (micro SD) card not included (Max to 256GB)
Dimmension [mm]
72 x 108
Product Compliance
This product complies with the following EU Directives: 2014/53/EU,
2011/65/EU.
Introduction
The smart camera is a component of the ENGO Smart system. It is used for
visual monitoring of the premises. It provides convenient control of high-
quality images: panorama, different viewing angles (camera tilt degrees),
zoom, horizontal and vertical rotation. It is programmed and operated in the
ENGO Smart mobile app. It enhances the security of the supervised premises.
Product features
4Mpx 2560*1440P
2-way audio
Motion detection
Move tracking
Infrared (IR) up to a distance of 10m Pan-tilt-zoom (PTZ), horizontal 355°,
vertical 110°
Angle of lance 108°
Electronic nanny function
WDR technology (optimizing image exposure)
vertical/horizontal installation
possibility to create automation and scenarios in the ENGO Smart application
Safety information
Use in accordance with national and EU regulations. Use the device only as
intended, keeping it in a dry condition. The product is for indoor use only.
Please read the entire manual, before installation or use.
Camera description
1
4 2
3 5
6
8
7
1. Microphone 2. Camera lens 3. LED diode 4. IR illumination 5. Micro SD slot
6. Loudspeaker 7. USB type C power socket 8. Reset button
Inserting a memory card
Slide the black part of the camera in the direction indicated by the arrow.
Slide the card into the micro SD card slot until you hear a click.
Micro SD slot
Installation of the camera in the app
Make sure your router is within range of your smartphone. Make sure you are
connected to the Internet. This will reduce the pairing time of the device.
STEP1 – DOWNLAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install it
on your smartphone.
Powered By
STEP 2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:
1
2
Click,,Sign Up”to create
Enter your e-mail
new account.
address to which the
verification code will be sent.
3
4
Enter the verification code received in the email. Remember that you only have
60 seconds toenter the
code!
Then set the login password.
STEP 3A – CONNECT CAMERA TO WI-FI- Connection via Bluetooth
After installing the app and creating an account:
1
2
STEP 3B – CONNECT CAMERA TO WI-FI- Connection via QR Code
After installing the app and creating an account:
1
2
STEP 3B – CONNECT CAMERA TO WI-FI- Connection via QR Code
9
10
11
On your mobile device, make sure the ENGO Smart has access to
permissions (Location, Bluetooth, Nearby devices). Then turn on
Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you
want to assign the device.
Make sure the camera is powered on. Then press and hold the button on the back of the camera for approximately 5 seconds, until the beep. The blue LED on the front of the unit will then start flashing. The pairing mode is enabled.
3
4
5
On your mobile device, make sure the ENGO Smart has access to
permissions (Location, Bluetooth, Nearby devices). Then turn on
Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you
want to assign the device.
Make sure the camera is powered on. Then press and hold the button on the back of the camera for approximately 5 seconds, until the beep. The blue LED on the front of the unit will then start flashing. The pairing mode is enabled.
3
4
5
Select the Wi-Fi network Point the camera at the in which the camera will QR code displayed in the operate and enter the app, click ,,I heard the password of this network. sound”after the beep.
Wait for the app to configure the device with the selected
Wi-Fi network.
12
13
In the app, select: ,,Add Device”.
After finding the camera, go,,Add”
Select the Wi-Fi network in which the camera will
operate and enter the password of this network.
6
7
8
In the app, select: ,,Add Device”.
Find and click on the Wi-Fi camera in the
device list.
Then go,,Next”.
6
7
8
Wait for the app to configure the device with the selected
Wi-Fi network.
Go ,,DONE”.
The camera has been installed and displays the main interface.
Follow the instructions displayed on the smartphone screen.
Go ,,DONE”.
The camera has been installed and displays the main interface.
Factory reset
To restore the default settings of the camera, hold down the Reset button for
about 5 seconds until a beep sounds. Then release the button. The camera will
restart, restore the default (factory) values and be ready to be added to the
application again.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>