ENGO Controls E901WIFI Internet Wireless Thermostat User Guide

ENGO Controls E901WIFI Internet Wireless Thermostat

Product Information

Specifications:

• Model: E901WIFI
• Type: Internet, wireless thermostat
• Power Source: Battery (batteries not included)
• Wireless Frequency: 868.0 MHz – 868.6 MHz
• WiFi Connectivity: Yes
• Compatible Devices: Smartphone, Tablet
• Compatible Applications: ENGO Smart, TUYA Smart

Introduction:
The E901WIFI is a wireless, Wi-Fi room thermostat designed for economical and ecological control of any type of heating system. It offers simple operation and allows users to adjust the heating cycle according to their daily rhythm. The thermostat comes with a built-in WiFi module in the receiver, enabling remote control of the heating system using a smartphone or tablet through the ENGO Smart or TUYA Smart application. The devices are pre- paired and ready to use.

Product Usage Instructions

Wall Mounting:

1. Remove the thermostat cover by following the instructions below:
2. If there are batteries inside, remove them.
3. Use a screwdriver to push the plastic tabs in until you feel resistance.
4. Tilt the front part of the housing to separate it from the back part.
5. Choose an appropriate location on the wall for mounting.
6. Use screws and anchors (not included) to securely attach the back part of the thermostat to the wall.
7. Align the front part with the back part and snap them together until they are firmly attached.

Connecting to WiFi:

1. Make sure your WiFi network is available and functioning properly.
2. Download and install the ENGO Smart or TUYA Smart application on your smartphone or tablet from the respective app store.
3. Open the application and create an account if required.
4. Follow the in-app instructions to add a new device.
5. When prompted, enter the WiFi credentials to connect the thermostat to your home network.
6. Once connected, you can control and adjust the heating settings remotely through the application.

INTRODUCTION

E901WIFI is a wireless, Wi-Fi room thermostat which enables economical and ecological control of any type of heating. The operation of the thermostat is very simple and allows the user to adjust the heating cycle to user’s rythm of the day. Built-in WiFi module (in the receiver) enables remote control of the heating system via a smartphone or a tablet using the ENGO application Smart / TUYA Smart. The devices are pre-paired and ready for work.

Product Compliance
This product complies with the following EU

Directives : 2014/53/EU, 2016/65/EU 868.0 MHz – 868.6 MHz; <13dBm WIFI 2,4 GHz

Please note!
This document is a brief manual of the installation and operation of the product and highlights its most important features and functions.

SAFETY INFORMATION:
Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Please read the entire manual, before installation or use.

INSTALLATION:
Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions.

WARNING:
For the entire installation, there may be additional protection requirements, which the installer is responsible for.

Care for the natural environment is of paramount importance to us. The awareness that we manufacture electronic devices obliges us to dispose of used electronic components and devices safely. Therefore the company has received a registration number issued by the Chief Inspector for Environmental Protection. The crossed out symbol the trash can on the product means that the product must not be disposed of with ordinary waste containers. Sorting waste for recycling helps to protect the environment. It is the user’s responsibility to surrender used equipment to a designated collection point for recycling waste from electrical and electronic equipment.

Wall mounting

1. Remove the thermostat cover as shown in the picture. If there are batteries inside, remove them
2. Use a screwdriver to push the plastic tabs in as shown in the figure until you feel resistance, and tilt the front part of the housing.
3. Separate the front part from the back part in the direction shown above
4. Use the supplied mounting screws and mount the back cover to the wall (use holes as shown arrows)
5. Using the hinges on the left, fold the front and back covers together as shown in the picture above until they click into place.

Wiring Diagrams

E901RXWIFI receiver

Receiver’s switches description:

LEFT SWITCH

ON – Manual mode – receiver ON
OFF – Manual mode – receiver OFF
RIGHT SWITCH
MANUAL – Receiver works in manual mode (according to the left switch)
AUTO – Receiver works in AUTO mode (according to the thermostat’s command)

LED indications in the receiver

A detailed explanation of the meaning of the LEDs can be found in the table below:

The red LED flashes

| Thereceiver and thermostatarepreparedfor installation in the app.

The LED always flashes red:

-if thethermostathasnotbeenaddedtotheapplication

– after starting the parameter“APP”->YES (in installer settings)

– after removing the thermostat from the application (deviceautomaticallyentersthepairingmodewithapp)

---|---
The green lights up| The receiver is connected to a router but there is no connection to Internet (router is offline)
The green LED flashes| the receiver lost connection with a router (router is off)
The blue LED lights up| The receiver is connected to a router that has In- ternet access (router is online)

The blue LED flashes

| The receiver was paired but lost communication with the thermostat due to out of range or low battery in the thermostat. When receiver lost communication with thermostat it starts flashing after 15 minutes.

The orange LED lights up

| In automatic mode, the receiver received a heat- ing / cooling signal from the thermostat or

the receiver was started in manual mode (left switch ON, right switch MANUAL)

The orange LED flashes

| The receiver is in the pairing mode and is looking for a signal from the thermostat (then you must activate the “SYNC” parameter in the thermo- stat). The receiver was paired but lost communi- cation with the thermostat due to out of range or low battery in the thermostat. Orange diode starts flashing 15 minutes after lost communica- tion from the thermostat.
The orange LED is off| The receiver does not send a heating / cooling signal.

The pink LED is on

| Update process started. To increase the chance of success of the update – immediately after the pink diode appears, click any thermostat’s button to turn on backlight

LCD icon description

1. AM/PM
2. Clock
3. Day of the week indicator
4. Settings icon
5. Key lock function
6. Send a signal (pairing)
7. Internet connection
8. Holiday Mode
9. Low battery indicator
10. Antifrost Mode
11. Cooling mode
12. Heating mode
13. Temperature unit
14. Room / setpoint temperature
15. Manual mode/ Temporary override mode
16. Program number

Button description

Setting Time / Setting Date
In the online mode – the thermostat reads the current time from the application. In the offline mode – D/H/M buttons are active and day/time can be set manually

• Press D button to set the day
• Press H button to set the hour.
• Press M button to set the minutes.

Manual mode temperature settings
In manual mode, the thermostat maintains a constant setpoint temperature as long as the user will not change it again or will not switch to another operating mode (e.g. schedule mode).

Setting setpoint temperature in manual mode

Press any button to highlight the screen, then follow the steps below:

• Press , button to enter manual mode. The hand icon should be visible on the display.
• Using or button set new comfort temperature value.
• Confirm by button or wait until the thermostat will approve your choice itself and display the main screen.

OFF mode

Press any button to highlight the screen, then follow the steps below:

• Press , button to enter OFF mode.
• LCD is turned OFF, Thermostat is not sending signal for heating/cooling to the receiver.
• To exit the OFF mode press again the button. The thermostat will return to the previous mode.

Installation of the E901WIFI thermostat in the app

Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the de-vice. Use only Wi-Fi 2,4GHz network

• STEP 1 – DOWNLOAD ENGO SMART ENGO SMART APP
  Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.

• STEP 2 – REGISTER THE NEW ACCOUNT
  To register a new account, please follow the steps below:

  • Click „Register” to create new account.
  • Enter your e-mail address to which the verification code will be sent.
  • Enter the verification code received in the email. Remember that you only have 60 seconds to enter the code!
  • Then set the login password.

• STEP 3 – CONNECT THE THERMOSTAT TO WI-FI

  1. After installing the app and creating an account:
  2. Turn on Wi-Fi and Bluetooth on your smartphone. Connect mobile phone to the Wi-Fi network to which you want to assign the thermostat.
  • Connect the receiver to the power supply.
  • When first powered up, the red led will start flashing, which means that devices are ready to be added to the application.
  • Go to step 7 (adding devices in the app).
  • If the red LED on the receiver is not flashing, proceed with the next steps.
  3. Press and hold button for 5 seconds.
  4. Use or , button to choose APP – add to application parameter.
  5. Confirm with button.
  6. Use or button to choose YES and confirm with (OK) button to start the process of adding to the application .
  7. In the app, select: „Add Device”.
  8. Then choose: „Auto Scan”.
  9. After finding the thermostat, go „Next”.
  10. Select the Wi-Fi network which thermostat should connect and put it’s password.
  11. Wait for the app to configure thermostat.
  12. Name the device and click „Done”.
  13. Thermostat has been installed and displays the main interface.
  14. It shows on the main app window.
  15. When the blue LED on the receiver will light up, it means the device has been correctly added to the application and is now connected to the Internet.

E901WIFI pairing process with the receiver

PLEASE NOTE! E901WIFI THERMOSTAT IS ALREADY PAIRED WITH THE RECEIVER!

1. If you want to re-pair the receiver and thermostat with each other and then add it to the application, make sure that the receiver is disconnected from the power supply, and the switches on it are in the ON and AUTO positions.
2. Then connect the receiver to the power supply and wait a few seconds.
3. Next, move the left switch to the OFF position and back to the ON position with a quick motion. The orange LED will start blinking, which will confirm that the receiver has entered the pairing mode.
4. Press and hold the button for 5 seconds.
5. Use or , button to select SYNC parameter.
6. Confirm with button.
7. Using or buttons choose YES and start the pairing process on a new frequency by pressing the button .
8. The thermostat started to send a signal to find the receiver (the symbol of the blinking antenna) and started the countdown with the number 10 (min). The pairing process may take up to 10 minutes.
9. When the orange LED stops blinking, the devices have been paired on a new frequency.
10. The thermostat will display the message „good”, which means that the devices are successfully paired with each other. Thermostat will return to the next APP parameter in the service menu (adding to application). You can skip this step and return to the main menu by clicking (OK) button a few times

WARNING! If the orange LED on the receiver has not stopped blinking after 10 minutes, repeat the pairing process taking into account the distance between devices, obstacles and interference.

Installer settings

1. To enter installer parameters press and hold button for 5 seconds.
2. Use or button to move between parameters. Enter the parameter by Edit the parameter using or Confirm the new parameter value with the button .

Installer parameters

P02

| ****

Control algorithm

| 1| SPAN ±0,25°C| ****

1

2| SPAN ±0,5°C
3| TPI for Underfloor Heating
4| TPI for Radiators
5| TPI for Electrical Heating

P03

| Offset temperature| -3.5°C to + 3.5°C| If the thermostat indicates wrong temperature, you can correct it by ± 3.5°C| ****

0°C

P04| Relay type| NO| Normally Open type of relay| NO
NC| Normally Closed type of relay
P05| Clock format| 24h| 24 hour| 24h
12h| 12 hour

P06

| Minimum setpoint| ****

5°C – 34,5°C

| Minimum heating / cooling temperature that can be set| ****

5°C

P07

| Maximum setpoint| ****

5,5°C – 35°C

| Maximum heating / cooling temperature that can be set| ****

35°C

P08| Key sound| NO| Key sound Off| YES
YES| Key sound On
P09| PIN Code| NO| Disabled| NO
PIN| Enabled

P10

| ****

Require a PIN to unlock the keys every time

| NO| Function disabled| ****

YES

YES| Function enabled

SYNC

| ****

Pairing with receiver function

| NO| Function disabled| ****

NO

YES| Function enabled

APP

| Pairing with application function| NO| Function disabled| ****

NO

YES| Function enabled

CLR

| Clear settings factory reset| NO| No action| ****

NO

YES| Factory Reset

Technical specification

Producer:
Engo Controls S.C. 43-200 Pszczyna 3E Górnośląska St. Poland

Distributor:
QL CONTROLS Sp z o.o. Sp. k. 43-262 Kobielice 4 Rolna St. Poland

www.engocontrols.com

FAQ

What EU Directives does this product comply with?

This product complies with the following EU Directives: 2014/53/EU, 2016/65/EU.

References

• ENGO Controls - Sterowanie ogrzewaniem

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>