HORNBACH 10445861 Flair LED Ceiling Light Instruction Manual

: September 14, 2024
: HORNBACH

Table of Contents

HORNBACH 10445861 Flair LED Ceiling Light
Specifications
Product Usage Instructions
FAQ
Safety information
Used symbols
Description
Technical data
Assembly
Connection
Remote control
Maintenance and care
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HORNBACH 10445861 Flair LED Ceiling Light

Specifications

Opal Cover: Opalabdeckung
Rated Voltage: 230 V~
Frequency: 50/60 Hz
Light Source: 25 W
Protection Class: I
Protection Rating: IP 20
Energy Efficiency: Class F
Color Temperature: 3000-6500 K
Remote Control: 2 x AAA batteries 1.5 V (not rechargeable)
Luminous Flux: 2700 lm
Dimensions: Weight: 0.95 kg

Product Usage Instructions

Installation

Unscrew the Opal cover from the light fixture.
Replace the light source if necessary.
Screw the Opal cover back onto the light fixture.
Restore power supply.

Operation

To operate the light:

A. Turn on the light using the remote control.
B. Adjust brightness levels.
C. Set timer function (light turns off after 30 seconds).
D. Choose from 3 color temperature settings (3000/4000/6500 K).

Maintenance and Care

To maintain the light:

Clean the fixture with a soft, dry cloth. Do not use abrasive powders or chemicals.

FAQ

Q: Can this light fixture be used outdoors?
- A: No, it is not recommended to use this light fixture outdoors or in damp environments.
Q: How do I replace the batteries in the remote control?
- A: The remote control uses 2 non-rechargeable AAA batteries. To replace them, remove the battery cover and insert new batteries of the same type.

Please read these instructions carefully and keep them safe for later use!

Safety information

Electrical work and repairs must be performed by a qualified electrician.
During installation, always observe the national installation regulations.
The luminaire must not be modified in any way. Risk of electric shock and accident.
The light source and the control gear of this luminaire are only replaceable by a qualified electrician.

For use of batteries

CAUTION! Explosion hazard when the batteries are not replaced correctly. Only replace by batteries of the same type. Pay attention to the correct polarity.
Do not expose batteries (battery pack or inserted batteries) to excessive heat from sunlight, fire, etc.
Protect from mechanical shocks.
Keep dry and clean. Keep out of reach of children.
Do not open, disassemble, cut open, or short-circuit batteries.
Do not use old and new batteries together.
Observe the safety notes and other notes on the battery and its packaging.
Remove leaking batteries and clean the battery compartment thoroughly. Avoid contact with eyes and skin.
Do not ingest the battery, chemical burn hazard.
Do not charge non-rechargeable batteries.

Used symbols

Caution: Risk to health and the product.
Do not use it outdoors or in damp environments.
Cannot be dimmed (only by remote control).
Class I appliance. Must be connected to a protective ground.
Light source replaceable by a qualified electrician.
Control gear is replaceable by a qualified electrician.
This product contains a light source of the energy efficiency class F.

Waste disposal

The crossed-out wheeled bin symbol requires separate disposal for waste electrical and electronic equipment (WEEE). Such equipment may contain valuable, but dangerous and hazardous substances. You are required by law to return these products to a designated collection point for the recycling of WEEE and must not under any circumstances dispose of them as unsorted municipal waste. In this way, you can help to conserve resources and protect the environment.

In Germany, HORNBACH is obliged:

to take back old appliances of the same type free of charge in HORNBACH stores when you purchase a new electrical or electronic appliance.
to take back up to 3 WEEE of the same type (up to max. 25 cm edge length) free of charge in HORNBACH stores, even if you do not purchase a new appliance.
when delivering a new electrical or electronic appliance to a private household, to collect an old appliance of the same type free of charge or to enable you to return it in your immediate vicinity.

Make sure that lamps which can be removed from the appliance without destroying it have been removed from the appliance before disposing of it. Make sure that all batteries have been removed from the appliance before disposing of it. You will find notes on this in the operating instructions (see Chapter IV. Battery change). For further details, please consult www.hornbach.com or your local authorities. Used batteries and rechargeable batteries must be disposed of properly. Battery selling stores and municipal collection points offer special containers for battery disposal. Precise data on the type and chemical system of the batteries can be found in the technical data, corresponding markings on the batteries themselves. Children must not play with plastic bags and packaging material, due to the risk of injury and suffocation. Store such material safely or dispose of it in an environmentally friendly way

Description

Opaque cover
Fastening holes
Luminaire
Power supply
Cable inlet
3 x screws / plugs
Remote control
2 x non-rechargeable batteries 1.5 V, AAA

Technical data

Nominal voltage 230 V~ 50/60 Hz
Rated power 25 W
Protection class I
Degree of protection IP 20
Energy efficiency of
light source class F
Color temperature 3000-6500 K
Luminous flux 2700 lm
Dimensions Ø 400 mm
- H: 69.5 mm
Weight 0.95 kg

Assembly

Caution!

First, disconnect the power supply for this connection.

Unscrew the opaque cover from the luminaire.
Select an installation location without pipes or cables behind it. Mark the fastening holes using the luminaire as a template, and drill the holes.
Route the power cable through the cable inlet.
Insert the plugs and fasten the luminaire with the screws.
Caution!
Make sure the fasteners are suitable for the ceiling material. Connect the power supply cable to the luminaire (see section III).
Screw the opaque cover back onto the luminaire.
Connect the power supply.

Connection

Connect the luminaire to the power supply (see figure). Make sure that the connections are tight and that no loose cable endings emerge from the terminal. The product needs to be earthed.

Remote control

A ON
B Change to warm white
C Change to cold white
D Night light (10% brightness)
E Timer function (luminaire turns off after 30 sec)
F 3-Step colour temperature (3000/4000/6500 K)
G Match all LEDs to remote control settings
H Decrease brightness
I Increase brightness
J OFF

Maintenance and care

Cleaning:

Wipe the the luminaire with a soft, dry cloth only. Never use scouring powders or chemical cleaning agents. Never allow the electrical components to become damp

Battery change:

Please observe the exact polarity and type (AAA 1.5 V).