Kanlux 12W CCT O W Ceiling Mounted LED Light Fitting Instruction Manual
- September 12, 2024
- Kanlux
Table of Contents
Kanlux 12W CCT O W Ceiling Mounted LED Light Fitting Instruction Manual
Symbols
INTENDED USE / APPLICATION
Product designed for the use in households and for other similar general applications.
MOUNTING
Technical changes reserved. Read the manual before mounting. Mounting should be performed by an appropriately qualified person. Any activities to be done with disconnected power supply. Exercise particular caution. Mounting diagram: see pictures. Check for proper mechanical fastening and connection to electrical power prior to first use. The product can be connected to a supply network which meets energy quality standards as prescribed by law. To maintain the proper IP protection level, the right diameter of the power cable should be selected for the cable gland used in the product.
FUNCTIONAL CHARACTERISTICS
Product can be used either indoors or outdoors.
USAGE GUIDELINES / MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. Product
may heat up to a higher temperature. Product with non-replaceable light source
of the LED type.
Product cannot be fixed if the light source becomes damaged. ATTENTION! Do not
look directly at LED light beam. Product can only be supplied by rated voltage
or voltage within the range provided. It’s forbidden to use the product with
damaged protective cover. Product must not be used in unfavorable conditions,
e.g. dust, water, moisture, vibrations, explosive air atmosphere, fumes, or
chemical fumes, etc. Replacing the light source in the housing is impossible.
If the light source is damaged replace the entire housing. It is not possible
to disassemble the light source and control panel without permanently damaging
the product and losing the declared tightness degree of the equipped product
(lighting fixture).
EXPLANATIONS OF SYMBOLS USED
P1: Rated voltage, frequency.
P2: Rated power.
P3: Rated luminous flux.
P4: The specified luminous flux refers to the light source (LED module)
used.
P5: Colour temperature.
P6: Rated durability.
P7: Colour Rendering Index.
P8: Certificate of Conformity confirming the quality of production in
accordance with approved standards on the territory of the Customs Union.
P9: Class II. A product in which protection against electric shock is
provided not only through basic insulation, but also double or reinforced
insulation.
P10: The symbol describes the minimal distance of a light fixture (its light source) from the spots and objects that it’s illuminating.
P11: Viewing angle.
P12: Dust-proof product. Protection against water jets provided.
P13: Product can be used either indoors or outdoors.
P14: The product is not compatible with lighting dimmers.
P15: The product can only be used in a lighting fixture with protective
glass. The chipped globe, screen or protective shield must be replaced
immediately.
P16: Product meets the requirements of EU directives.
P17: Environmental operating temperature range that the product can be
exposed to.
P18: Caution, risk of electric shock.
P19: This product is equipped with a light source with energy efficiency
class D,E.
P20: The product is compliant with all relevant United Kingdom
regulations.
P21: The product meets the requirements of technical regulations
applicable in Ukraine.
P22: It is not possible to replace the LED light source.
P23: It is not possible to replace the control panel or control equipment.
ENVIRONMENTAL PROTECTION
Keep your environment clean. Segregation of post-packaging waste is
recommended.
P24: This labelling indicates the requirement to selectively collect
waste electronic and electrical equipment.
Products labelled in this way must not be disposed of in the same way as other
waste under the threat of a fine. These products may be harmful to the natural
environment and health, and require a special form of recycling/neutralising.
Products labelled in this way should be returned to a collection facility for
waste electrical and electronic goods. Information on collection centres is
provided by local authorities or sellers of such goods. Used items can also be
returned to the seller when new product is purchased, in quantity no larger
than the purchased item of the same type. The above rules regard the EU area.
In the case of other countries, regulations in force in a given country must
be applied. Contacting the distributor of our products in a given area is
recommended.
COMMENTS / GUIDELINES
Failure to follow these instructions may result in e.g. fire, burns, electrical shock, physical injury and other material and non-material damage. For more information about Kanlux products visit www.kanlux.com. Kanlux SA shall not be responsible for any damage resulting from the failure to follow these instructions. Kanlux SA reserves the right to make changes in the manual – the current version can be downloaded at www.kanlux.com.
Connection
Through-wiring of the fixtures possible
Installation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>