SEALEY TP69.V3 Manual Vacuum Oil And Fluid Extractor Instruction Manual

September 12, 2024
SEALEY

SEALEY TP69.V3 Manual Vacuum Oil And Fluid Extractor

Specifications

  • Model: TP69.V3
  • Capacity: 6.5L
  • Type: Manual Vacuum Oil & Fluid Extractor
  • Manufacturer: Sealey

Product Usage Instructions

Safety

Ensure health & safety regulations are strictly followed. Wear eye protection. Do not use prohibited fluids.

Introduction

This product is designed for extracting oil and fluids efficiently and safely.

Operation

Pumping Procedure

  1. Press the vacuum release valve for 5 seconds to release vacuum within the pump.
  2. Seal off the fluid entry/pouring hole.
  3. Pump the handle up and down several times to expel any fluid from the pump.

Extracting Other Fluids

Select and insert the appropriate diameter probe into the fluid to be drained. Connect the extension tube to both the pump inlet and the probe. Follow steps similar to pumping procedure.

Environment Protection

Recycle unwanted materials properly. Dispose of tools, accessories, and packaging in an environmentally friendly manner. Drain fluids before disposal according to local regulations.

FAQ

  • Q: Can I use this extractor with all types of fluids?
    • A: No, only use approved fluids as specified in the instructions. Using prohibited fluids will invalidate the warranty.
  • Q: How should I store the extractor?
    • A: Store in a safe dry location away from high temperatures, direct sunlight, rain, or snow.

Product Information

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

  • WARNING! Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this equipment.
  • Familiarise yourself with the extractor’s application and limitations, as well as the specific potential hazards peculiar to this product.
  • Maintain the extractor in good condition.
  • Replace or repair damaged parts. Use genuine parts only. Unauthorised parts will invalidate the warranty.
  • Use only to extract engine or transmission oils, or similar NON-Corrosive fluids. Unit may also be used for the transfer of wat er.
  • Ensure safety eye protection and protective clothing are worn when using this product.
  • Keep the work area clean, and uncluttered and ensure there is adequate lighting.
  • Maintain correct balance and footing. Ensure the floor is not slippery and wear nonslip shoes.
  • Keep children and unauthorized persons away from the working area.
  • Dispose of waste liquids in accordance with local authority regulations.
  • DO NOT store fluids in the container. Once used to extract fluid, it must be emptied into an approved receptacle as soon as possible.
  • DO NOT use to extract hazardous or harmful chemicals, solvents, petrol, diesel, kerosene, alkaline or acids. If by chance such fluids are used in the unit, it must be immediately drained and thoro ughly cleaned. Use with prohibited fluids will invalidate your warranty.
  • DO NOT dismantle, tamper or adapt the extractor for any purpose other than for which it is designed.
  • DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage.
  • Keep the extractor clean and store in a safe dry location. DO NOT store in areas of high temperature, direct sunlight, rain or snow

SPECIFICATION

  • Model No:………………………………………………………. TP69.V3
  • Capacity: ………………………………………………………………. 6.5L
  • Suction probes: ………………….Ø5.8 x 850mm, Ø6.7 x 850mm
  • Extension tube: ………………………………………Ø9.8 x 1000mm

OPERATION

OIL EXTRACTION

  1. Ensure the vehicle is on level ground and run the engine for approximately 5 minutes to warm the oil and allow any contaminants within the oil to thoroughly mix and turn the engine off.
  2. Remove the vehicle’s oil dipstick.
  3. Select and insert the appropriate diameter probe into the dipstick hole until it reaches the bottom of the sump, see fig.2.
  4. Connect the extension tube to both the pump inlet and probe, see fig.2.
  5. Raise the handle to its highest limit and pump it fully several times to create a vacuum which will automatically begin to extract the oil/fluid. Observe the oil/fluid as it rises up the chamber and stop pumping when the fluid is 6”(150mm) from the top. The unit will continue to fill and will automatically shut off when the internal float valve operates. DO NOT continue to pump after the unit has shut off as this may result in liquid entering the inner pump chamber. If this should occur refer to section 4.1.8 on how to expel fluid from the pump.
  6. Once completed, remove the main suction tube from the pump, pour the oil/fluid into a suitable container (the unit can be tipped upside down to facilitate emptying) and dispose of it in accordance with local authority regulations.
  7. Before using the pump again press the vacuum release valve for 5 seconds to release the vacuum within the pump. This valve is situated on the top of the unit underneath the handle.
  8. In the event of fluid entering the inner pump chamber it can be expelled from the unit as follows. Firstly press the vacuum release valve for 5 seconds to release the vacuum within the pump. Seal off the fluid entry/pouring hole by placing your hand over it, then pump the handle up and down several times. Any fluid that has entered the pump will be expelled from the air valve on the underside of the unit.

OTHER FLUIDS

  1. Select and insert the appropriate diameter probe into the fluid to be drained.
  2. Connect the extension tube to both the pump inlet and the probe.
  3. The operation of the extractor is the same as described in sections 4.1.5 to 4.1.7.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

  • Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.
  • Important: No Liability is accepted for incorrect use of this product.
  • Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SEALEY User Manuals

Related Manuals