Darkglass Solid Series Vintage Deluxe User Guide

: September 12, 2024
: DARKGLASS

Table of Contents

Darkglass Solid Series Vintage Deluxe
Specs
Warning
Warranty
Disclaimer
FAQs
MORE INFO
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Darkglass Solid Series Vintage Deluxe

Darkglass-Solid-Series-Vintage-Deluxe-PRODUCT

Specs

Controls

Blend: Mixes the clean input signal with the overdriven signal. The clean signal remains at unity gain while the volume of the overdriven signal is set by the Level knob, allowing for fine control of the blend ratio.
Level: Sets the volume of the overdriven signal.
Drive: Sets the amount of saturation in the overdriven signal.
Grunt Switch: Sets the amount of low-frequency content to saturate by selecting between three different bass boost levels before the clipping stage.
Attack Switch: Sets the amount of treble content to
saturate: The “Boost” setting emphasizes the treble content’s extra clarity and presence. The “Flat” position leaves this register untouched while the “Cut” position will reduce the amount of high frequencies being saturated.
Low: +-12dB @100Hz|Low Mids: +-12dB @1kHz
Hi Mids: +-12dB @ 3 kHz| Treble: +-12dB @ 5kHz
Low Mids Switch: this switch changes the center frequency of the Low Mids from 1kHz to 500Hz.
Hi Mids Switch: this switch changes the center frequency of the Hi Mids from 3kHz to 1.5KHz.

Technical Specifications

Input Impedance: 500k0
Output Impedance: 1k0
Current Consumption: ~20mA
Voltage: 9V DC (Center Negative)

Dimensions

Width: 94 mm / 3,7″
Length: 120 mm/ 4,72″
Height: 46 mm / 1,81″
Weight: 320 g / 0,7lb

Warning

The Vintage Deluxe has a current draw of 30mA. Only use a regulated 9V DC adapter with a center-negative plug.
Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.

Warranty

To activate the warranty, we encourage you to register your product at: http://mypedal.darkglass.com and enter the serial number on the back of your pedal.
Please contact us via email support@darkglass.com before shipping a product to us.

Disclaimer

In the interest of continuous improvement, specifications are subject to change without notice.
If you have any questions, please don’t hesitate to contact us at www.darkglass.com.
The manufacturer claims that the above product fulfils the requirements as set by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, and WEEE.
1176®, and SSL® are registered trademarks of their respective companies.
Names of factory modes are intended for descriptive purposes only and should not be construed as an endorsement or affiliation with the companies or products named.

EMC/ EMI

This equipment has been tested and found to comply with the limits for a Class B Digital device, under part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
There is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FAQs

Q: What should I do if my unit is damaged due to incorrect power supply?
- A: Using unregulated power supplies or higher voltages can damage your unit and void the warranty. Always use a regulated 9V DC adapter with a center-negative plug as specified.