Darkglass Electronics V3 Vintage Deluxe User Manual
- June 17, 2024
- Darkglass Electronics
Table of Contents
USER MANUAL
Vintage Deluxe
Vintage Deluxe
The Deluxe is back with a vengeance
V3 Vintage Deluxe
Smooth overdriven bass sounds, or warming the signal with the Vintage Deluxe, it will give many alternatives to project a concrete bottom end top lay any style you will prefer.
Warning
The Vintage Deluxe has a current draw of 30mA. Only use a regulated 9V DC
adapter with a center-negative plug. Due to ecological reasons it does not
accept batteries. Unregulated power supplies and/or higher voltages may result
in suboptimal noise performance and even damage your unit, voiding the
warranty.
Warranty
To activate the warranty, we encourage you to register your product on:
http://mypedal.darkglass.com and enter the serial number on the back of your
pedal.
Please contact us via email
support@darkglass.com before shipping a
product to us.
Controls
Blend: Mixes the clean input signal with the overdriven signal. The clean
signal remains at unity gain while the volume of the overdriven signal is set
by the Level knob, allowing for fine control of the blend ratio.
Level: Sets the volume of the overdriven signal.
Drive: Sets the amount of gain in the overdriven signal. Grunt Switch:
Sets the amount of low frequency content to saturate by selecting between
three different bass boost levels before the clipping stage.
Attack Switch: Sets the amount of treble content to saturate: The “Boost”
setting emphasizes the treble content extra clarity and presence. The “Flat”
position leaves this register untouched while the “Cut” position will reduce
the amount of high frequencies being saturated.
Low: +-12dB @ 100Hz | Low Mids: +-12dB @ 1kHz | Hi
Mids: +-12dB @ 2.8kHz | Treble: +-12dB @ 5kHz.
Parallel Output: Hardwired copy of your input signal, useful for getting a
clean signal in recording and live situations Direct Output: A balanced
version of the ¼” output, useful for running into PA’s or studio mixing
consoles.
Technical Specifications
| Input Impedance | 500k |
|---|---|
| Output Impedance | 1k |
| Current Consumption | ~20mA |
| Voltage | 9V DC (Center Negative) |
Dimensions
Width| 106 mm (4.21 in)
Height| 120 mm (4.72 in)
Depth| 45 mm (1,77 in)
Weight| 350 g (0.78 lb)
Disclaimer
In the interest of continuous improvement, specifications are subject to change
without notice. If you have any questions, please don’t hesitate to contact us
at www.darkglass.com
The manufacturer claims that the above product fulfills the requirements as set
by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, WEEE.
EMC / EMI
This equipment has been tested and found to comply with the limits for a Class
B Digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
residential installations.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. There is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
DARKGLASS ELECTRONICS OY.
Helsinki, Finland
www.darkglass.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>