Darkglass B3K Microtubes Core Series User Guide

September 12, 2024
DARKGLASS

Darkglass-LOGO

Darkglass B3K Microtubes Core Series

Darkglass-B3K-Microtubes-Core-Series-PRODUCT

Specs

Controls

  • Blend: Mixes the clean input signal with the overdriven signal. The clean signal remains at unity gain while the volume of the overdriven signal is set by the Level knob, allowing for fine control of the blend ratio.
  • Tone: Controls the high-frequency content of the sound. A variable low pass filter from 3kHz (CCW) to 8kHz (cw).
  • Level: Sets the volume of the overdriven signal.
  • Drive: Sets the amount of saturation in the overdriven signal.
  • Grunt: When engaged provides a massive low-end boost to thicken your sound.
  • Mid Boost: Gives a subtle 6dB boost from 300 Hz to 1kHz to help you cut through a bit more.

Technical Specifications

  • Input Impedance: 500kΩ
  • Output Impedance: 1kΩ
  • Current Consumption: ~17mA
  • Voltage: 9V DC (Center Negative)

Dimensions

  • Width: 75 mm / 2,95″
  • Length: 111 mm/ 4,37″
  • Height: 43 mm / 1,69″
  • Weight: 250 g / 0,55 lb

Warning

  • The Microtubes B3K has a current draw of 20mA. Only use a regulated 9V DC adapter with a center-negative plug.
  • Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.

Warranty

Disclaimer

  • In the interest of continuous improvement, specifications are subject to change without notice.
  • If you have any questions, please don’t hesitate to contact us at www.darkglass.com.
  • The manufacturer claims that the above product fulfils the requirements as set by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, WEEE 1176®, and SSL® are registered trademarks of their respective companies.
  • Names of factory modes are intended for descriptive purposes only and should not be construed as an endorsement or affiliation with the companies or products named.

EMC / EMI

This equipment has been tested and found to comply with the limits for a Class B Digital device, under part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FAQs

  • Q: How should I power the Microtubes B3K?
    • A: Use a regulated 9V DC adapter with a center-negative plug to power the Microtubes B3K. Unregulated power supplies or higher voltages may lead to suboptimal noise performance and potential damage to the unit.
  • Q: How can I activate the warranty for my product?
  • Q: What are the dimensions and weight of the Microtubes B3K?
    • A: The Microtubes B3K dimensions are
    • Width: 75 mm / 2.95″,
    • Length: 111 mm / 4.37″,
    • Height: 43 mm / 1.69″,
    • Weight: 250 g / 0.55 lb.

MORE INFO

DARK GLASS is a registered trademark in the U.S., number 4,616,801, owned by Darkglass Electronics Oy. Designed by Revolve Studio

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DARKGLASS User Manuals

Related Manuals