Darkglass Solid Series Alpha Omega User Guide

: September 12, 2024
: DARKGLASS

Table of Contents

Darkglass Solid Series Alpha Omega
Product Information
Product Usage Instructions
Frequently Asked Questions
Specification
Safety Warning
Warranty
Disclaimer
EMC/EMI
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Darkglass Solid Series Alpha Omega

Product Information

Specifications

Input Impedance: 1M
Output Impedance: 1k
Current Consumption: ~30mA
Voltage: 9V DC (Center Negative)

Dimensions

Width: 94 mm/3.7″
Length: 120 mm/4.72″
Height: 46 mm/1.81″
Weight: 320 g/0.7 lb

Product Usage Instructions

Controls
The Microtubes B7K features the following controls:
- Bass
- Mids
- Treble
- Blend
- Level
Power Requirements
Ensure to use a regulated 9V DC adapter with a center-negative plug to power the pedal. Using unregulated power supplies or higher voltages may damage the unit and void the warranty.
Care and Maintenance
Keep the pedal clean and free from dust or debris. Avoid exposing it to extreme temperatures or moisture. Regularly check the connections and cables for any signs of wear or damage.

Frequently Asked Questions

How do I activate the warranty for my product?
To activate the warranty, register your product at http://mypedal.darkglass.com and enter the serial number located on the back of your pedal. Contact support@darkglass.com before shipping a product for warranty claims.
What should I do if my pedal causes interference?
If your equipment causes interference, try reorienting or relocating the receiving antenna, increasing separation between devices, or connecting the equipment to a different outlet. Consult a professional for assistance if needed.
Where can I find more information about product updates?
For the latest information and updates on our products, visit www.darkglass.com or contact us directly with any questions.

Darkglass Electronics

Specification

Controls

Blend: Mixes the clean and processed signals. The clean signal remains at unity gain while the volume of the overdriven signal is set by the Level knob, allowing for fine mix tuning.
Level: Sets the volume of the overdriven signal.
Drive: Sets the amount of gain in the overdriven signal.
Bite: Boosts High Mids (2.8kHz) for additional presence and definition.
Growl: Shelving Bass Boost for a fatter tone and increased low-end saturation.
Mod: Selects or mixes between the two distinct circuits: Alpha is punchy, and tight with a lot of definition, whereas Omega is simply brutal and raw.
Bass: +-12dB @ 80Hz
Mid: +-12dB @ 500Hz
Treble: +-12dB @ 5kHz

Technical Specifications

Input Impedance: 1MΩ
Output Impedance: 1kΩ
Current Consumption: ~30mA
Voltage: 9V DC (Center Negative)

Dimensions

Width: 94 mm / 3,7″
Length: 120 mm/ 4,72″
Height: 46 mm / 1,81″
Weight: 320 g / 0,7 lb

Safety Warning

The Microtubes B7K has a current draw of 20mA. Only use a regulated 9V DC adapter with a center-negative plug. Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.

Warranty

To activate the warranty, we encourage you to register your product at: http://mypedal.darkglass.com and enter the serial number on the back of your pedal. Please contact us via email at support@darkglass.com before shipping a product to us.

Disclaimer

In the interest of continuous improvement, specifications are subject to change without notice. If you have any questions, please don’t hesitate to contact us at www.darkglass.com The manufacturer claims that the above product fulfills the requirements as set by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, WEEE.
1176®, and SSL® are registered trademarks of their respective companies. Names of factory modes are intended for descriptive purposes only and should not be construed as an endorsement or affiliation with the companies or products named.

EMC/EMI

This equipment has been tested and found to comply with the limits for a Class B Digital device, under part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

DARK GLASS is a registered trademark in the U.S., number 4,616,801, owned by Darkglass Electronics Oy.

Designed by Revolve Studio.

Darkglass Electronics