REMARK RK-C2076S-03C R1-Spec Dual Catback Owner’s Manual
- June 1, 2024
- REMARK
Table of Contents
REMARK RK-C2076S-03C R1-Spec Dual Catback
Product Information
Specifications:
- Manufacturer: Subaru
- Year: 2022+
- Model: WRX
- Trim: R1 SPEC.
- Chassis Code: VB
Parts List:
| No. | Description |
|---|---|
| P1 | 3 Composite 2-Bolt Gasket |
Installation Instructions:
- We recommend installation to be performed by a trained and/or qualified technician.
- Remove OE exhaust system: rear mufflers and midpipe.
Maintenance and Warranty:
1-year limited manufacturer defect warranty from date of purchase. All
warranty claims are subject to inspection by REMARK at our facility. Limited
Warranty only applies to the original purchaser of the product.
REMARK is not responsible for fitment issues on non-US spec vehicles as all products are developed on US spec models. Product finishes are not covered under warranty and considered wear & tear. No warranty whatsoever will be valid if the defect was caused by abuse, negligence, and/or mishandling. This includes weather conditions, natural disasters, any road/off-road conditions, and any accidents/collision you were part of.
Acidic cleaning products or steel wool are not to be used unless by a trained professional. Some chemical cleaning products may damage the product and/or finishes.
FAQ:
Q: How should I clean the Burnt finish tips?
A: If optioned with the Burnt finish tips, make sure to only clean with
car wash soap and water. Some cleaners may affect the Burnt finish.
PRODUCT INFORMATION
MANUFACTURER: SUBARU
YEAR: 2022+
MODEL: WRX
TRIM: –
CHASSIS CODE: VB
REMARK PART #: RK-C2076S-03C : R1 SPEC. DUAL CATBACK w/ RESONATOR, STAINLESS
STEEL
RK-C2076S-03TC : R1 SPEC. DUAL CATBACK w/ RESONATOR, BURNT STAINLESS
PARTS LIST
| No. | Descr | Part Num. | Qty | Torque |
|---|---|---|---|---|
| 1 | 3” Composite 2-Bolt Gasket | 76C2-T03 | 1 | |
| 2 | 3“ Metal 2-Bolt Gasket | 76C2-01 | 1 | |
| 3 | 2.5” Metal 2-Bolt Gasket | 65C2-S01 | 2 | |
| 4 | M10 Serrated Hex Head Bolt L=35mm | M10B35 | 6 | ~42 ft-lbs. |
| 5 | M10 Serrated Nut | M10N | 6 | ~42 ft-lbs. |
| 6 | M8 Serrated Hex Head Bolt L=35 | M8B35 | 2 | ~25 ft-lbs. |
| 7 | M8 Serrated Nut | M8N | 2 | ~25 ft-lbs. |
| A | Front Resonated Midpipe Section | N/A | 1 | |
| B | Rear “T” Midpipe Section | N/A | 1 | |
| C | Driver’s Side Muffler Canister | N/A | 1 | |
| D | Passenger’s Side Muffler Canister | N/A | 1 |
PARTS LAYOUT
INSTALLATION
- We recommend installation to be performed by a trained and/ or qualified technician.
- Remove OE exhaust system: rear mufflers and midpipe.
- Remove OEM donut style gasket from downpipe (downpipe to midpipe connection). No adapter is needed.
- Install REMARK exhaust components using the original rubber hangers unless otherwise noted.
- Install all gaskets and hardware. Leave the hardware hand tight.
- Align flanges, gasket, and snug all hardware so that sections cannot move.
- Check positioning of the exhaust piping, and tips(s). Reposition if needed by loosening hardware, adjust position and retighten hardware.
- When placement is confirmed, tighten all hardware to recommend torque spec.
- Gently shake/ move the exhaust system to ensure there is proper clearance around the entire system, especially the tips to bumper.
- Throughly wipe down the exhaust system from any grease, dirt, handprints, fingerprints, etc… as these may cause a permanent stain once the exhaust reaches operating temp. NOTE: If optioned with the Burnt finish tips, make sure to only clean with car wash soap and water. Some cleaners may affect the Burnt finish.
- Start the engine
- Check for any leaks, fitment issues, rubbing, etc..
- Re-check for exhaust leaks, fitment issues, and re-torque all hardware after ~100 miles of driving.
WARRANTY POLICY
-
1-year limited manufacturer defect warranty from date of purchase
-
All warranty claims are subject to inspection by REMARK at our facility
-
Limited Warranty only applies to the original purchaser of the product
-
REMARK is not responsible for fitment issues on non-US spec vehicles as all products are developed on US spec models
-
Product finishes are not covered under warranty and considered wear & tear
-
No warranty whatsoever will be valid if the defect was caused by abuse, negligence and/or mishandling. That includes weather conditions, natural disasters, any road/off-road conditions, and any accidents/collision you were part of.
Acidic cleaning products or steel wool are not to be used unless by a trained professional. Some chemical cleaning products may damage the product and/or finishes. -
Wear and tear (the damage that happens to our product in ordinary use) is not covered by our limited warranty.
-
Improper installation or misuse of the product may lead to failure and damage to both product and vehicle. The user assumes all responsibility.
-
All products are intended for use off-public streets and highways. Vehicle manufacturer warranty may be voided should any modification(s) or removal(s) of OEM(factory) components are determined.
-
Federal and state law may prohibit the removal, modification or rendering of any device affecting vehicle emissions or state regulated decibel limits. It is the customer’s responsibility to be aware of federal, state and local laws.
User assumes all cost and risks associated with purchase and installation of aftermarket components. REMARK is not responsible for any fees, fines, or any type of penalties you have received from any authority.
Buyers are responsible for all return shipping fees unless otherwise noted REMARK does not cover any installation, un-installation, labor fees, or related
REMARK. INC. 16782 HALE AVE, STE A. IRVINE CA 92606 SALES@REMARK- USA.COM 949.366.7661
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>