REMARK RK-C1063H-11 CIVIC Sports Touring Catback Exhaust User Guide

REMARK RK-C1063H-11 CIVIC Sports Touring Catback Exhaust

Specifications

• Manufacturer: HONDA
• Year: 2022+
• Model: CIVIC SPORT SEDAN
• Engine: 2.0L NA
• Trim: FE2
• Chassis Code: RK-C1063H-11, RK-C1063H-11T
• Part #: RK-C1063H-11
• Description: CATBACK CONFIG – 2.5 IN / 304 STAINLESS STEEL CONSTRUCTION / SINGLE TIP

Product Usage Instructions

1. Installation Recommendations
   • We recommend professional installation by a trained technician.
   • Install the product when the exhaust is cool to the touch.
   • Ensure OEM rear bumper lower cover/diffuser modifications are made.
2. Installation Steps
   • Remove OEM exhaust and components.
   • Install original rubber hangers on the REMARK exhaust.
   • Install exhaust components [A], [B], [C] starting from the front.
   • Torque bolts to specifications (~35 ft-lbs).
   • Align and snug hardware, and adjust position if needed.
   • Check to position and tighten all hardware to the recommended torque.
   • Wipe down the system before starting the engine.
   • Check for leaks and fitment issues, and re-torque hardware after driving 100 miles.

FAQ

• Q: What does the warranty cover?
• A: The warranty covers manufacturer defects and is valid for one year from the date of purchase. Inspection by REMARK is required for warranty claims.
• Q: How often should I inspect the system?
• A: Inspect all components and retighten hardware every 3000-5000 miles at regular service intervals.
• Q: Can I use harsh cleaners on the exhaust tips?
• A: Avoid harsh cleaners on the tips to prevent permanent discoloration. Use soap and water for cleaning.

PRODUCT INFORMATION SHEET

• MANUFACTURER: HONDA
• YEAR: 2022+
• MODEL: CIVIC
• TRIM: SPORT SEDAN, 2.0L NA
• CHASSIS CODE: FE2
• REMARK PART #: RK-C1063H-11, RK-C1063H-11T
• DESCRIPTION: CATBACK CONFIG – 2.5 IN / 304 STAINLESS STEEL CONSTRUCTION / SINGLE TIP

PARTS LIST

ITEMS NOT TO SCALE – FOR REFERENCE ONLY

Dimensions

PARTS LAYOUT

INSTALLATION

IMPORTANT: INSTALLATION OF THIS PRODUCT REQUIRES MODIFICATION OR REPLACEMENT OF OEM REAR BUMPER LOWER COVER/ DIFFUSER

1. We recommend installation to be performed by a trained and/ or qualied technician

2. Installation should be performed when the exhaust is cool to the touch

3. Remove OEM exhaust and/or exhaust components

4. Install the original rubber hangers from the OEM exhaust onto the REMARK exhaust

5. Begin to install the components of the exhaust [A] [B] [C]. It may be easier to install the exhaust in sections instead of as an assembled complete exhaust due to the weight and size. We recommend starting from the front first and working your way rearwards, starting with [A].

6. Install the forward section of the mid-pipe [A] to the factory front over the pipe. Use the provided 3-bolt gasket and re-use the OEM nuts. Torque to OEM specification or ~35 ft-lbs.

7. Use the supplied gaskets and hardware to install sections [B] and [C] of the exhaust leaving the hardware hand-tight until the entire system is installed.

8. Align flanges, and gaskets, and snug all hardware so that sections cannot move.

9. Check the positioning of the exhaust piping, resonator, user (s), and tips(s). Reposition if needed by loosening hardware, adjusting the position and retightening hardware.

10. When placement is confirmed, tighten all hardware to recommend torque spec.
    INSTALLATION TIP – If the position of the tips needs to be adjusted, loosen the range hardware, have someone hold the tips in the desired position, and retighten the hardware.

11. Thoroughly wipe down the exhaust system from any grease, dirt, handprints, fingerprints, etc… as these may cause a permanent stain once the exhaust reaches operating temp. DO NOT USE any harsh cleaners on the polish or burnt nish tips as permanent discolouration may occur. We recommend soap and water for the tips.

12. Start the engine and let the system come up to temp.

13. Check for any leaks, tment issues, rubbing, etc..

14. Re-check for exhaust leaks, and tment issues, and re-torque all hardware after ~100 miles of driving.

We highly recommend that all system components be inspected, and ALL hardware retightened at normal service intervals. Every 3000-5000 miles.

WARRANTY POLICY

• 1-year limited manufacturer defect warranty from the date of purchase
• All warranty claims are subject to inspection by REMARK at our facility
• Limited Warranty only applies to the original purchaser of the product
• REMARK is not responsible for FItment issues on non-US spec vehicles as all products are developed on US spec models
• Product FInishes are not covered under warranty and are considered wear & tear
• No warranty whatsoever will be valid if the defect was caused by abuse, negligence and/or mishandling. That includes weather conditions, natural disasters, any road/off-road conditions, and any accidents/collisions you were part of.
• Acidic cleaning products or steel wool are not to be used unless by a trained professional. Some chemical cleaning products may damage the product and/or FInishes.
• Wear and tear (the damage that happens to our product in ordinary use) is not covered by our limited warranty.
• Improper installation or misuse of the product may lead to failure and damage to both the product and the vehicle. The user assumes all responsibility.
• All products are intended for use on public streets and highways. Vehicle manufacturer warranty may be voided should any modification (s) or removal(s) of OEM(factory) components be determined.
• Federal and state law may prohibit the removal, modification or rendering of any device affecting vehicle emissions or state-regulated decibel limits. It is the customer’s responsibility to be aware of federal, state and local laws.
• The user assumes all costs and risks associated with the purchase and installation of aftermarket components. REMARK is not responsible for any fees, nes, or any type of penalties you have received from any authority.
• Buyers are responsible for all return shipping fees unless otherwise noted
• REMARK does not cover any installation, uninstallation, labour fees, or related.

CONTACT

• REMARK, INC. 16782 HALE AVE, STE A, IRVINE CA 92606 SALES@REMARK-USA.COM 949.366.7661

References

• USA Location information - USA.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>