tp-link POE2412G Series Passive PoE Adapter Installation Guide
- September 13, 2024
- tp-link
Table of Contents
- Connection
- Installation
- LED & Button
- Specifications
- FAQ
- Q1. Can the PoE adapter supply power to a passive PoE device which doesn’t
- Q2. Can the Passive PoE adapter supply power to all my PoE devices?
- EU Declaration of Conformity
- SAFETY NOTICES
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
tp-link POE2412G Series Passive PoE Adapter Installation Guide
Note: POE2412G is used as an example throughout this guide. Other models may differ in appearance.
Connection
Use the passive PoE adapter to simultaneously supply power and transmit data to a passive PoE device.
Note: Before connecting a passive PoE device, please check the required voltage in its product manual.
Installation
Note: To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward.
-
Drill two holes on the wall and insert the plastic wall anchors into the the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward.
-
Attach the passive PoE adapter to the mounting bracket by sliding the adapter in the direction of the arrows until it locks into place.
LED & Button
Specifications
General Specifications
Standards | IEEE802.3i, IEEE 802.3u, IEEE 802.3ab |
---|---|
Output Power | POE2412G: 24V/0.5A |
POE4818G: 48V/0.375A
POE4824G: 48V/0.5A
Cable Type| UTP/STP of Cat. 5e or above (based on the standards that the
connected devices comply with)
Ports|
- 10/100/1000Mbps Auto-Negotiation RJ45 LAN port
- 10/100/1000Mbps Auto-Negotiation RJ45 POE port
LED| PWR
Environmental and Physical Specifications
Operating Temperature| POE4818G/POE4824G: 0˚C to 40˚C (32˚F to 104˚F)
POE2412G: 0˚C to 45˚C (32˚F to 113˚F)
---|---
Storage Temperature| -40˚C to 70˚C (-40˚F to 158˚F)
Operating Humidity| 10% to 90%RH non-condensing
Storage Humidity| 5% to 90%RH non-condensing
FAQ
Q1. Can the PoE adapter supply power to a passive PoE device which doesn’t
have a gigabit Ethernet port?
: Yes. Both the LAN and the PoE ports of the PoE adapter comply with IEEE 802.3i and IEEE 802.3u standards and support 10/100Mbps Auto-Negotiation.
Q2. Can the Passive PoE adapter supply power to all my PoE devices?
A: If your devices support passive PoE and the voltage standards of the devices match that of the passive PoE adapter, the passive PoE adapter can supply power to them.
FCC compliance information statement
Product Name: I.T.E. POWER SUPPLY
Model Number: POE2412G/POE4818G/POE4824G
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https ://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above
has been shown to comply with the applicable technical standards, FCC part 15.
There is no unauthorized change is made in the equipment and the equipment is
properly maintained and operated.
Issue Date: 2023/12/18
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https ://www.tp-link.com/en/ce.
SAFETY NOTICES
Cautions
Keep the device away from water, fire, humidity or hot environments.
Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.
Plug the product into the wall outlets with earthing connection through the
power supply cord.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
The Poe ports shall not be used to charge lithium batteries or devices
supplied by lithium batteries.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Explanation of the symbols on the product label
Symbols may vary from products. The label is at the bottom of the product.
Symbol | Explanation |
---|---|
Class II equipment | |
Class II equipment with functional earthing | |
Alternating current | |
Direct current | |
Polarity of D.Sc. power connector | |
For indoor use only | |
Dangerous voltage | |
Caution, risk of electric shock | |
Energy efficiency Marking | |
Protective earth | |
Earth | |
Frame or chassis | |
Functional earthing | |
Caution, hot surface | |
Caution | |
Operator’s manual | |
Stand-by | |
“ON”/”OFF” (push-push) | |
Fuse | |
Fuse is used in neutral N | |
RECYCLING |
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. User has the choice to
give his product to a competent recycling organization or to the retailer when
he buys a new electrical or electronic equipment.
| Caution, avoid listening at high-volume levels forlongperiods
| Disconnection, allpowerplugs
m| Disconnection, allpowerplugs
µ| Switch of micro- gap construction (for US version) Switch of micro-
gap /micro-disconnection construction (for other versions except US)
ε| Switch without contact gap (Semiconductor switching device)
For technical support and other information, please visit
https ://www.tp-link.com/
support/?type=smb, or simply scan the QR code
References
- Link: Simple, secure one-click payments
- CE Regulatory Compliance | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link
- WiFi Networking Equipment for Home & Business | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>