WLMOUSE SWORD X Magnesium Gaming Mouse User Manual
- September 12, 2024
- WLMOUSE
Table of Contents
WLMOUSE SWORD X Magnesium Gaming Mouse
Specifications:
- Dimensions: 123mm x 67mm x 42mm
- Connectivity: Wired (USB 3.0) and Wireless (USB 3.0)
Product Usage Instructions
Wireless Mode Setup:
Pairing Steps:
- Unplug the mouse from the computer and switch it to wireless mode.
- Hold down the left and right mouse buttons along with the front side button for 3 seconds.
- Once the green LED on the mouse flashes faster, connect the dongle to the computer using the included cable.
- When the LED on the mouse turns off, pairing is complete.
DPI Setting:
The default DPI is 1600 DPI. To adjust DPI levels:
- Press and hold the left mouse button, right mouse button, and scroll wheel simultaneously for 3 seconds.
Polling Rate Setting:
The default polling rate is 1000Hz. To change the polling rate:
- Press and hold the mouse side button, scroll wheel, and right button together for 3 seconds.
FAQ:
Q: How do I pair the dongle if the mouse cannot be used in wireless mode?
A: Follow the Dongle Pairing instructions provided in the manual.
Q: How many DPI levels are available?
A: There are 6 DPI levels ranging from 400 DPI to 26000 DPI.
Q: What are the default polling rate levels for wired and wireless
connections?
A: The default polling rate levels are as follows:
- Wired connection: 125 Hz, 250 Hz, 500 Hz, 1000 Hz
- Wireless connection: 125 Hz, 250 Hz, 2000 Hz, 4000 Hz, 500 Hz, 8000 Hz
Thanks for choosing WLMOUSE. If you have any questions or comments, if you
need any help with your products, please do not hesitate to contact us.
support@wlmouse.com
www.wlmouse.com
FEATURES
- length: 4.84inch / 123mm
- width: 2.64inch / 67mm
- height: 1.65inch / 42mm
- weight: 47 ±2g
- MCU: Nordic 52840
- Sensor: PAW3950 HS
- Polling Rate: 125-8000Hz (Adjustable)
- Encoder: TTC Dust-Proof silver
- Switches (Main): TTC Nihil Transparent Black Dot /Omron Opticals
- Side Buttons: Omron Blue Dots
- Battery: Lithium-Ion Polymer 300Mah Capacity
- Reciever: Nordic 52820, High Speed Chip
WIRED
WIRELESS
To achieve the best performance for the mouse, please ensure that the distance between the receiver and the mouse does not exceed 50 cm, and that there are no wireless interference devices around the mouse. Additionally, please connect to a USB 3.0 port or higher.
Dongle Pairing
If the mouse cannot be used in wireless mode, please use the following method to pair the dongle.
- 1 Left Button
- 2 Right Button
- 4 Forward Button
Pairing Steps
- Unplug the mouse from the computer. Switch the mouse back into wireless mode to start the process of pairing.
- Hold the left and right mouse buttons, along with the front side button for 3 seconds.
- Once the green LED on the mouse starts flashing faster than normal, connect the 4k dongle to the computer with the included cable.
- When the LED on the mouse turns off, pairing has been completed.
DPI Setting
The default DPI is set to 1600 DPI, and you can adjust the DPI levels in the driver settings.
- Left Button
- Right Button
- Scroll Wheel
There are 6 DPI levels. To switch the DPI, press and hold the left mouse button, right mouse button, and scroll wheel/middle mouse button simultaneously for 3 seconds.
Polling Rate Setting
- Right Button
- Scroll Wheel
- Back Button
wired connection
- 125 Hz
- 250 Hz
- 500 Hz
- 1000 Hz
Wireless connection
- 125 Hz
- 250 Hz
- 2000 Hz
- 4000 Hz
- 500 Hz
- 8000 Hz
- 1000 Hz
The mouse polling rate is default set to 1000Hz. To switch the polling rate, press and hold the mouse side button, scroll wheel/middle button, and right button simultaneously for 3 seconds.
LOD (Lift off Distance) Setting
- 1 Left Button
- 3 Scroll Wheel
- 4 Forward Button
LOD Levels
- 1 mm
- 2 mm
Switching Between 1K and 8K Dongle
- 3 Scroll Wheel
- 4 Forward Button
- 5 Back Button
To switch between the 1K Nano dongle and the 8K dongle, simultaneously press and hold the mouse’s front side button, back side button, and scroll wheel/middle button
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used by the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.