tp-link tapo TC40 Outdoor Pan/Tilt Security Wi-Fi Camera User Guide

tapo TC40 Outdoor Pan/Tilt Security Wi-Fi Camera

“`html

Specifications

• Product: Outdoor Pan/Tilt Security Wi-Fi Camera

• Models: TC40, Tapo C500, Tapo C510W

• Features: Weatherproof, Pan/Tilt functionality, Motion
  detection, Siren system

• Power: 12V DC power adapter

• Storage: microSD card slot (card not included)

Product Usage Instructions

1. Setting Up the Camera

To set up your camera, follow these steps:

1. Download the Tapo App from the App Store or Google Play, or
   scan the QR code provided.

2. Log in to the app using your TP-Link ID or create a new account
   if you don’t have one.

3. Add your camera by tapping the designated button in the app and
   selecting your camera model. Follow the app instructions to
   complete the setup.

2. Resetting the Camera

If needed, you can reset the camera by following these
steps:

1. Loosen the screws on the camera.
2. While the camera is powered on, use a pin to press and hold the
   RESET button for at least 5 seconds until the System LED blinks
   red.

3. Using microSD Card Slot

If you wish to use a microSD card for local recording, follow
these steps:

1. Loosen the screws on the camera to access the microSD card
   slot.

2. Insert a microSD card (not included) into the slot.

3. Initialize the microSD card using the Tapo app.

4. Amazon Frustration-Free Setup

If you have the Tapo C500 model and wish to use Amazon
Frustration-Free Setup, follow these steps:

1. Follow the LED indications for FFS setup status.
2. If needed, manually add the Tapo device by pressing the Reset
   button on your camera and following the app instructions.

Frequently Asked Questions (FAQ)

Q: Can I access the camera feed remotely?

A: Yes, you can access the camera feed from anywhere using the
Tapo app.

Q: What should I do if the LED does not turn solid green during

Amazon Frustration-Free Setup?

A: If this occurs, try adding the Tapo device manually by
following the provided instructions in the app.

“`

User Guide
Outdoor Pan/Tilt Security Wi-Fi Camera
TC40/Tapo C500/Tapo C510W

©2023 TP-Link 1910013472 REV1.1.0

Contents
About This Guide ··········································································· 1 Introduction ······················································································ 2 Appearance ······················································································ 3 Set Up Your Camera····································································· 5 Set Up Using Amazon Frustration-Free Setup·············· 6 Install a microSD Card······························································ 10 Mount Your Camera··································································· 11 Install Waterproof Items·························································· 14 How to Reset Your Camera ··················································· 15 Authentication·············································································· 16

About This Guide

This guide provides a brief introduction to the Outdoor Pan/Tilt Security Wi- Fi Camera and the Tapo app, as well as regulatory information.
Please note that features available in Tapo may vary by model and software version. Tapo availability may also vary by region. All images, steps, and descriptions in this guide are only examples and may not reflect your actual Tapo Camera experience.

Conventions
In this guide, the following convention is used:

Convention Description

Blue

Key information appears in blue, including management page text such as menus, items, buttons and so on.

Underline Hyperlinks are in blue and underlined. You can click to redirect to a website.

Note:

Ignoring this type of note might result in a malfunction or damage to the device.

More Info
· Specifications can be found on the product page at https://www.tapo.com. · Our Technical Support and troubleshooting information can be found at https://www.tapo.com/support/. · The setup video can be found at https://www .tp-link.com/support/setup-video/#cloud-cameras.

1

Introduction
Outdoor Pan/Tilt Security Wi-Fi Camera is a full-featured weatherproof security camera that you can access from anywhere. Receive instant notifications and check feeds when the motion is detected. Moreover, the automatic siren system will trigger light and sound to frighten away unwanted visitors after the camera detects motion. Day or night, rain or shine, the Tapo camera protects what you love most.
· Smart Motion Tracking ­ Tracks and follows a subject smartly, keeping it within the camera’s field of view. · 1080p Full HD Live View ­ Reveals sharp images and vivid details. · Patrol Mode ­ Keep the camera cruise between two customized points for dynamic monitoring. · Person Detection ­ Notifies you when a person is detected. · Local* and Cloud Storage ­ Save recorded videos to an installed microSD card (up to 512 GB)*, or use Tapo Care* cloud storage service.
microSD card must be purchased separately. Subscribe for cloud storage at https://www.tapo.com/tapocare/ · IP65 Weatherproof ­ Offers excellent waterproof and dustproof performance for outdoor scenarios. · Customizable Sound Alarm ­ Record your own audio as an alarm to extend your usage. · Night Vision (up to 98 ft) ­ Ensure your safety by providing a clear visual distance of up to 98 ft even in total darkness. · Two-Way Audio ­ Communicate remotely with a delivery person in real time. · Multiple Installation Options ­ Use the mounting screws, template and loops to install on any wall, ceiling or pole for the perfect view. Mounting loops purchased separately. · Physical Privacy Mode ­ Maintains your privacy with the lens physically blocked by the housing.
2

Appearance
56

3

microSD

1

4

2

7

8

1 IR LEDs 2 Microphone 3 Lens 4 System LED

5 Reset
Loosen the screws. While the camera is powered on, use a pin to press and hold the RESET button for at least 5 seconds until the System LED blinks red.
6 microSD Card Slot
Loosen the screws and insert a microSD card. Initialize it on the Tapo app for local recording.
microSD card not included.

7 Speaker
8 DC Power Connector
Used to connect to a 12V DC power adapter

3

System LED Indication

Solid red Blinking red and green Blinking red slowly Solid amber Solid green Blinking red quickly Blinking green quickly

Starting up Ready for setup Connecting to Wi-Fi Connected to Wi-Fi Connected to the cloud Camera resetting Camera updating

4

Set Up Your Camera
Follow the steps below to get started with your new camera.

Step 1. Download Tapo App
Get the Tapo app from the App Store or Google Play, or by scanning the QR code below.

Step 2. Log In
Open the app, and log in with your TP-Link ID. If you don’t have an account, create one first.

Step 3. Add Your Camera
Tap the button in the app and select your model. Follow app instructions to complete the setup.

OR

5

Set Up Using Amazon Frustration-Free Setup

Note: Amazon Frustration-Free Setup is only available for Tapo C500. TC40 doesn’t support Amazon Frustration-Free Setup.
What is Amazon Frustration-Free Setup?
Amazon Frustration-Free Setup can help connect and set up Tapo smart devices in fewer steps, without having to remember and re-enter your Wi-Fi password on each device. To use this feature, confirm the following: The new Tapo device supports Amazon FFS. The new Tapo device is purchased from Amazon. You have an Amazon FFS enabled Alexa device or router. You have saved your Wi-Fi information to Amazon by using Alexa echo. Your Tapo device and router are on the same network as your Alexa echo.

LED Indications during Amazon Frustration-Free Setup

LED Blinking red and green Blinking amber Solid green

Status Ready for setup FFS setup in progress Working properly

If the LED does not turn solid green after a long time, you can try to add the Tapo device manually. (Press the Reset button on your Tapo device once. Then open the Tapo app, tap the + button on the page, select your device model, and follow the app instructions. )

6

How to use Amazon Frustration-Free Setup with Tapo devices

1. Open the Amazon Alexa app. Then tap More and select Skills & Games.

2. Enter Tapo in the search bar and choose Tapo.

7

3. Tap the ENABLE TO USE button.

4. Log in with your TP-Link ID that has bound to your Tapo device, and tap Authorize. After authorized successfully, the message Tapo has been successfully linked will come up.

8

5. Plug in your Tapo device and the setup will complete automatically in two minutes. For setting up more Tapo devices, just plug in and enjoy! Done! If this device displays on the Home page in the Tapo app, it indicates this device has been successfully associated with your Amazon account and joined your Wi-Fi network automatically. If this device does not display on the Home page in the Tapo app, try setting it up manually. (Tap the + button on the page, select your device model, and then follow the app instructions.)
9

Install a microSD Card

Follow the steps below to install the microSD card for local recording. You can go to Camera Settings > microSD Card in the Tapo app to check the card status or format your card.

1. Manually rotate the camera downwards. Loosen the screws on the panel and remove the cover.

2. Identify the direction of the microSD card and carefully insert the card into the slot. Push in the card until you hear a clicking sound.

microSD
10

Mount Your Camera
When you finish adding your camera in the Tapo app, you can mount it on a wall or ceiling with the provided mounting template and screws. You can also mount it on the pole with mounting loops. Follow the steps below to mount your new camera.
Note: The camera is not waterproof when set on a table or shelf. Mount the camera via Option 1, 2 or 3 when installing outdoors.

Option 1: Wall Mount
1. Affix the Camera and Bracket Route the camera power cord through the opening of the bracket. Use two bracket screws to affix the bracket and the camera.

3. Mount the Camera
Insert four mounting anchors into the holes, then use the mounting screws to affix the camera and bracket over the anchors.

2. Drill Holes
Stick the mounting template to the desired mounting place. Drill four screw holes according to the template.

=6 mm (15/64 in.)

4. Power Up the Camera
Connect the camera to a power outlet using the provided power adapter. Install the waterproof seal for the power connectors.

Male Power Connector Waterproof Seal Female Power Connector

11

Option 2: Overhang Mount
1. Affix the Camera and Bracket Route the camera power cord through the opening of the bracket. Use two bracket screws to affix the bracket and the camera.

3. Mount the Camera
Insert four mounting anchors into the holes, then use the mounting screws to affix the camera and bracket over the anchors.

2. Drill Holes
Stick the mounting template to the desired mounting place. Drill four screw holes according to the template.

=6 mm (15/64 in.)

4. Power Up the Camera
Connect the camera to a power outlet using the provided power adapter. Install the waterproof seal for the power connectors.

Male Power Connector Waterproof Seal Female Power Connector

12

Option 3: Pole Mount
1. Affix the Camera and Bracket Route the camera power cord through the opening of the bracket. Use two bracket screws to affix the bracket and the camera.

2. Mount the Camera Mount the camera on the pole using two pole-mounting loops (loop width 12mm).
Pole-mounting loops are not included.

Pole-mounting loops

3. Power Up the Camera
Connect the camera to a power outlet using the provided power adapter. Install the waterproof seal for the power connectors.

Male Power Connector Waterproof Seal Female Power Connector

13

Install Waterproof Items
When the camera is installed outdoors, please install waterproof items to waterproof your camera. Make sure each part is securely attached and the water-proofing rings are flush to keep out water. Follow the steps below to install waterproof items.
Install Waterproof Seal for Power Connectors
Connect the camera to a power outlet using the provided power adapter. Install the waterproof seal for the power connectors when the camera is installed outdoors.
Male Power Connector Waterproof Seal Female Power Connector
14

How to Reset Your Camera

Follow the steps below to reset your camera via the Reset button. You can also go to Camera Settings in the Tapo app and tap Remove Device at the bottom to factory reset your camera.

1. Manually rotate the camera downwards. Loosen the screws on the panel and remove the cover.

2. Press and hold the Reset button for at least 5 seconds until the LED blinks red.

Reset Button
15

Authentication
FCC compliance information statement
Product Name: Outdoor Pan/Tilt Security Wi-Fi Camera Model Number: Tapo C500/TC40/Tapo C510W Component Name Model I.T.E. Power Supply T090085-2B1 Responsible Party: TP-Link USA Corporation Address: 10 Mauchly, Irvine, CA 92618 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
16

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2023-08-02
FCC compliance information statement
Product Name: I.T.E. Power Supply Model Number: T090085-2B1 Responsible Party: TP-Link USA Corporation Address: 10 Mauchly, Irvine, CA 92618 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 17

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP- Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2023-08-02
18

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
OPERATING FREQUENCY (the maximum transmitted power)
2412MHz–2472MHz (20dBm)
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tapo.com/en/support/ce/.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body.
UKCA Mark
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tapo.com/support/ukca/.
19

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. l’appareil ne doit pas produire de brouillage; 2. l’utilisateurdel’appareildoitacceptertoutbrouillageradioélectriquesubi,memesilebrouillageestsusceptibled’encompromettrelefonctionnement
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
Korea Warning Statements:
.
20

NCC Notice & BSMI Notice

· · · · · · · 40

Outdoor Pan/Tilt Security Wi-Fi Camera Equipment name

Tapo C500/TC40/Tapo C510W Type designation (Type)

Unit
PCB

Lead (Pb)

Restricted substances and its chemical symbols

Mercury
(Hg)

Cadmium
(Cd)

Hexavalent chromium (Cr+6)

Polybrominated biphenyls
(PBB)

Polybrominated diphenyl ethers
(PBDE)

21

–

–

1. 0.1 wt % 0.01 wt %
Note 1″Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.

Note 2″” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
3.-

Note 3The “-” indicates that the restricted substance corresponds to the exemption.

, .

22

Safety Information
· Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid. · Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. · Do not use damaged charger or USB cable to charge the device. · Do not use any other chargers than those recommended · Do not use the device where wireless devices are not allowed. · Adapter shall be easily accessible. · Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t
hesitate to contact us. · Adapter should be used indoors where the ambient temperature is lower than or equal to 40ºC. · This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers
and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device. · Operating Temperature: -30 ºC ~ 60 ºC (-22°F ~ 140°F ) · Adapter should be used indoors where the ambient temperatureis lower than or equal to 40°C. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
23

Explanation of the symbols on the product label
Symbols may vary from products Symbol Class II equipment Class II equipment with functional earthing Alternating current DC voltage Polarity of output terminals Indoor use only Dangerous voltage Caution, risk of electric shock Energy efficiency Marking Protective earth
Earth

Explanation

Frame or chassis 24

Symbol

Functional earthing

Explanation

Caution, hot surface Caution Operator’s manual

Stand-by

“ON”/”OFF” (push-push)
Fuse
Fuse is used in neutral N RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Caution, avoid listening at high volume levels for long periods

Disconnection, all power plugs 25

Symbol m µ

Explanation Switch of mini-gap construction Switch of micro-gap construction (for US version) Switch of micro-gap / micro-disconnection construction (for other versions except US)
Switch without contact gap (Semiconductor switching device)

26

References

• Link: Simple, secure one-click payments
• Tapo | Smart Devices for Smart Living
• Regulatory Compliance | Tapo
• UKCA | Tapo
• Tapo Care | Tapo

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>