JBL GO3 Portable Bluetooth Speaker User Guide
- September 9, 2024
- JBL
Table of Contents
JBL GO3 Portable Bluetooth Speaker
Specifications:
- Transducer: 43 x 47 mm / 1.5
- Output Power: 4.2 W RMS
- Frequency Range: 110 Hz – 20 kHz
- Signal-to-Noise Ratio: > 85 dB
- Battery Type: Li-ion polymer 2.775 Wh (equivalent to 3.7 V/750 mAh)
- Battery Charging Time: 2.5 hours (5 V 1 A)
- Bluetooth Version: 5.1
- Bluetooth Profiles: A2DP 1.3, AVRCP 1.6
- Bluetooth Frequency Range: 2400 MHz – 2483.5 MHz
- Bluetooth Power: 8 dBm (EIRP)
- Dimensions: 87.5 x 75 x 41.3 mm / 3.4 x 2.7 x 1.6
- Weight: 0.209 kg / 0.46 lbs
Product Usage Instructions
-
Bluetooth Pairing:
To pair your device with Bluetooth: -
Turn on the JBL Go 3.
-
Make sure it is in discoverable mode.
-
Access the Bluetooth settings on your device.
-
Select “JBL Go 3” from the list of available devices.
-
Once connected, you will hear a confirmation sound.
-
Charging:
To charge the device: -
Connect the provided charging cable to the JBL Go 3.
-
Plug the other end into a power source with specifications of 5V/1A.
-
The device will show a charging indicator.
-
A full charge takes approximately 2.5 hours.
-
Waterproof and Dustproof:
The JBL Go 3 is rated IP67 for water and dust resistance, allowing you to use it in various environments with confidence. -
Playback:
To play audio through the JBL Go 3: -
Ensure the device is powered on and connected to your audio source.
-
Press the play button on the speaker to start playback.
Frequently Asked Questions (FAQ):
-
Q: How long does the battery last on a full charge?
A: The battery can last up to 5 hours, depending on the volume level and audio content being played. -
Q: What is the Bluetooth version of the JBL Go 3?
A: The JBL Go 3 features Bluetooth version 5.1 for wireless connectivity.
WHAT’S IN THE BOX
Bluetooth pairing
Play
CHARGING
WATERPROOF DUSTPROOF IP67
TECH SPECIFICATION
- Transducer: 43 x 47 mm / 1.5”
- Output power: 4.2 W RMS
- Frequency response: 110 Hz – 20 kHz
- Signal-to-noise ratio: > 85 dB
- Battery type: Li-ion polymer 2.775 Wh (equivalent to 3.7 V / 750 mAh)
- Battery charge time: 2.5 hours (5 V= 1 A)
- Music play time: up to 5 hours (dependent on volume level and audio content)
- Bluetooth® version: 5.1
- Bluetooth® profile: A2DP 1.3, AVRCP 1.6
- Bluetooth® transmitter frequency range: 2400 MHz – 2483.5 MHz
- Bluetooth® transmitter power: ≤ 8 dBm (EIRP)
- Bluetooth® transmitter modulation: GFSK, π/4 DQPSK, 8DPSK
- Dimensions (W x H x D): 87.5 x 75 x 41.3 mm / 3.4 x 2.7 x 1.6 ”
- Weight: 0.209 kg / 0.46 lbs
To protect battery lifespan, fully charge at least once every 3 months. Battery life will vary due to usage patterns and environmental conditions. Do not expose the JBL Go 3 to liquids without removing the cable connection. Do not expose JBL Go 3 to water while charging. It may result in permanent damage to the speaker or power source. Chemicals, salt, or “foreign particles” in your pool or the ocean can damage the waterproof seals or harm the connector surface over time if not rinsed off after use. After a liquid spill or rinse, do not charge your speaker until it’s completely dry and clean. Charging when wet might damage your speaker. When using an external adapter, the output voltage/ current of the external adapter should not exceed 5V/3A.
- The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.
- HARMAN International hereby declares that the product JBL GO3 complies with the essential requirements and other relevant provisions of Directive 53/2014/EU and UK Radio Equipment Regulations 2017. The declaration of conformity may be consulted in the specs section of the product detail page, accessible from www.jbl.com or at www.jbl.com/doc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>