tp-link TL-PI30G PoE Injector Installation Guide

tp-link TL-PI30G PoE Injector

LED Explanation

• For TL-PI30G/TL-PI30G-M2
  • PWR
  • Off: Power off
  • Steady Yellow: Power on, no PoE power supply
  • Steady Green: Power on, normal PoE power supply
  • Flashing   Green: Abnormal PoE power supply
• For TL-PI60G/TL-PI90X
  • PWR
  • On: Power on
  • Off: Power off
  • PoE
  • On: Normal PoE power supply
  • Off: No powered device connected
  • Flashing: Abnormal PoE power supply

Note: For simplicity, we will take TL-PI30G for example in this Guide.

Connection

Note:

1. The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE AP, and PoE IP Phone through an Ethernet cable.
2. For TL-PI60G/TL-PI90X, plug the product into the wall outlets with an earthing connection through the power supply cord.

Specifications

General Specifications

Environmental and Physical Specifications

Safety Information

• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
• Plug the product into the wall outlets with an earthing connection through the power supply cord.
• The PoE ports shall not be used to charge lithium batteries or devices supplied by lithium batteries.
• Please read and follow the above safety information when operating the device.
• We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

FAQs

• Q1. Can the PoE injector supply power to a PoE device that doesn’t have a gigabit PoE port?
  • A: Yes. All RJ45 ports of the PoE injector support 10/100/1000 Mbps.
• Q2. What can I do if my PoE injector doesn’t supply power to the powered device or the supplied power is unstable?
  • A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE function.
  • A2: Ensure the power consumption of the PD doesn’t exceed the maximum power supply of the PoE injector, otherwise the overload protection of the PoE injector will be activated. The quality and length of the Ethernet cable may influence the reception of the power supply.
  • To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com/business to join TP-Link Community.
  • For technical support and other information, please visit https://www.tp-link.com/support/?type=smb, or simply scan the QR code.

FCC

FCC compliance information statement

• Product Name: PoE Injector
• Model Number: TL-PI30G/TL-PI60G/TL-PI30G-M2/TL-PI90X

Responsible party: TP-Link USA Corporation

• Address: 10 Mauchly, Irvine, CA 92618
• Website: https://www.tp-link.com/us/
• Tel: +1 626 333 0234
• Fax: +1 909 527 6804
• E-mail: sales.usa@tp-link.com.

This equipment has been tested and found to comply with the limits for a Class A digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP-Link USA Corporation, have determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made to the equipment and the equipment is properly maintained and operated. Issue Date: 2024.5.9
Issue Date: 2024.5.9

Industry Canada Statement

• CAN ICES-3 (A)/NMB-3(A)

Wall Mounting Requirements (for TL-PI60G/TL-P|90X)

• To mount the device on a wall, use 2 screws that comply with ANSI B1.1 4#, (5#), 6# standard and are more than 7 mm in length.
• When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

Explana On Of The Symbols

Explana one of the symbols on the product label
The Equipment marking is at the bottom of the device. Symbols may vary from product.

electrical and electronic equipment (WEEE). This means that this product must be handled under European directive 2012/19/EU to be recycled or dismantled to minimize its impact on the environment. Users have the choice to give their product to a competent recycling organization or the retailer when they buy new electrical or electronic equipment.
| Caution, avoid listening at high volume levels for long periods
| Disconnection, all power plugs
m| Switch of mini-gap construction
µ| Switch of micro-gap construction (for US version) Switch of micro-gap /micro-disconnection construction (for other versions except US)
ε| Switch without contact gap (Semiconductor switching device)

References

• Link: Simple, secure one-click payments
• TP-Link Product Support - Wireless Networking Equipment Support
• WiFi Networking Equipment for Home & Business | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>