robustel MG460 Hardware Maritime Cyber Security Instruction Manual

: September 8, 2024
: robustel

Table of Contents

robustel MG460 Hardware Maritime Cyber Security
Product Usage Instructions
**Regulatory and Type Approval Information
Radio Specifications for Europe
Safety Information
Technical Support
Overview
Package Checklist
Interface Descriptions
Hardware Installation
Login to the Device
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

robustel MG460 Hardware Maritime Cyber Security

robustel MG460 Hardware Maritime Cyber Security-
product

Specifications

RF Technologies: 2G, 3G, 4G, GNSS, Wi-Fi
EU Band Frequencies: 4G LTE FDD – B1/B3/B7/B8/B20/B28/B32, LTE TDD – B34/B38/B40/B42/B43/B46, 3G WCDMA – B1/B8, 2G GSM – B3/B8
Non-EU Band Frequencies: 4G LTE FDD – B2/B4/B5/B12/B13/B18/B19/B25/B26, LTE TDD – B39/B41, 3G WCDMA – B2/B4/B5/B6/B19, 2G GSM – B2/B5
Wi-Fi Frequency: 2.4 GHz – 2.412 ~ 2.484 GHz, 5 GHz – 5150-5250MHz, 5745-5825MHz
GNSS: GPS L1, Galileo E1, GLONASS G1, BDS B1I, SBAS L1 – 1559MHz to 1610MHz, BDS B2a, GPS L5, Galileo E5a – 1164MHz to 1215MHz

Product Usage Instructions

Radio Specifications
Make sure to comply with the specified RF technologies and frequency bands for operation in Europe and non-EU regions. Follow the guidelines for Wi-Fi frequency usage and GNSS frequencies.

Radiation Exposure Statement
Adhere to FCC and IC radiation exposure limits by maintaining a minimum distance of 20cm between the device and your body. Avoid co-location with other antennas or transmitters.

Disposal and Recycling
Dispose of the product properly by sending it to separate collection facilities for recovery and recycling. Ensure compliance with relevant EU directives and UK legislation.

Health Warning
Be aware that the product may expose you to chemicals including Lead, which is known to cause cancer and reproductive harm. Visit www.P65Warnings.ca.gov for more information.

FAQ:
Q: Where can I find more product documents or tools?
A: You can find additional product resources at www.robustel.com/documentation/

MG460
Hardware Manual

Version: 1.0.0
Date: Jun. 14, 2024

Robustel MG460 Hardware Manual

**Regulatory and Type Approval Information

**

Table 1: Toxic or Hazardous Substances or Elements with Defined Concentration Limits

Name of the Part	Hazardous Substances
(Pb)	(Hg)

Metal

parts

|

X1,2

| o| o| o| –| –| –| –| –| –
Circuit

modules

| o| o| o| o| o| o| o| o| o| o
Cables and cable

assemblies

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

Plastic and polymeric

parts

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

o:Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in RoHS2.0.

X:Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this part might exceed the limit requirement in RoHS2.0.

Indicates that it does not contain the toxic or hazardous substance.

Note: Excessive lead can be exempted.

Copper alloy containing up to 4 % lead by weight (RoHS Exemption 6(c)).
Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound (ROHS Exemption 7(c)-Ⅰ)

Radio Specifications for Europe

RF technologies	2G, 3G, 4G, GNSS, Wi-Fi*,
Cellular Frequency *	EU Band：

4G: LTE FDD: B1/B3/B7/B8/B20/B28/B32 LTE TDD: B34/B38/B40/B42/B43/B46 3G: WCDMA: B1/B8

2G: GSM: B3/B8

| Non-EU Band ：

4G : LTE FDD: B2/ B4/ B5/ B12/ B13/ B18/ B19/ B25/ B26

LTE TDD: B39/B41

3G : WCDMA: B2/B4/B5/B6/B19

2G : GSM: B2/B5

Wi-Fi Frequency| 2.4 GHz: 2.412 ~ 2.484 GHz

5 GHz: 5150-5250MHz, 5745-5825MHz

GNSS*| GPS L1, Galileo E1, GLONASS G1, BDS B1I, SBAS L1: 1559MHz to 1610MHz BDS B2a, GPS L5,

Galileo E5a: 1164MHz to 1215MHz

Max RF power| 33 dBm±2dB@GSM, 24 dBm+1/-3dB@WCDMA, 23 dBm±2dB@LTE, 19dBm@WiFi

May vary on difference models.

Note: Operation of 5150 ~ 5250 MHz frequency range is restricted to indoor use only.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC & IC Radiation Exposure Statement
This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Simplified EU Declaration of Conformity
We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan Road, Huangpu District, Guangzhou, China, declare that this radio equipment complies with all applicable EU directives. The full text of the EU DoC is available at the following internet address: www.robustel.com/certifications/

Safety Information

General

The router generates radio frequency (RF) power. When using the router, care must be taken on safety issues related to RF interference as well as regulations of RF equipment.
Do not use your router in aircraft, hospitals, petrol stations or in places where using cellular products is prohibited.
Be sure that the router will not be interfering with nearby equipment. For example: pacemakers or medical equipment. The antenna of the router should be away from computers, office equipment, home appliances, etc.
An external antenna must be connected to the router for proper operation. Only uses approved antenna with the router. Please contact the authorized distributor to find an approved antenna.

RF Exposure

This device meets the official requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies.
The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable limits.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Router may be used at this time.

The symbol indicates that the product should not be mixed with general household waste but must be sent to separate collection facilities for recovery and recycling.
The symbol indicates that the product meets the requirements of the applicable EU directives.
The symbol indicates that the product meets the requirements of the relevant UK legislation.

WARNING
This product can expose you to chemicals including Lead, known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Related download link
Find more product documents or tools at: www.robustel.com/documentation/

Technical Support

Tel: 4009-873-791
Email: support@robustel.com
Web: www.robustel.com

Document History
Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions.

Date| Firmware Version| Document Version| Change Description
---|---|---|---
Jun. 14, 2024| 2.1.3| 1.0.0| Initial release.
| | |
| | |
| | |
| | |
| | |

Overview

Robustel’s MG460 is a new generation of industrial maritime gateway which is compliant to IEC61162-460 (Maritime Safety and Security) standards and IEC60945 standards. The MG460 can be used as a gateway between on-board vessel equipment and external services (Cloud platforms, servers, etc).

Package Checklist

Before commencing installation ensure your package has the following components:

$robustel-MG460-Hardware-Maritime-Cyber-Security- $6$$

Note: The accessories could be different on specific order.

Panel Layout
(May vary on different models, please refer to Table1)

$robustel-MG460-Hardware-Maritime-Cyber-Security- $7$$

Table1

Model| PN| Cellular Antenna Port| WIFI Antenna Port| GNSS Antenna Port
---|---|---|---|---
MG460-A5ZAZ-NU| B147001| 0| 0| 0
MG460-A5CAZ-NU| B147002| 0| 2| 0
MG460-A5AAZ-4L-A06GL| B147003| 2| 0| 1
MG460-A5BAZ-4L-A06GL| B147004| 2| 2| 1

Interface Descriptions

Serial Ports. Two software configurable serial ports, could be configured as RS232 or RS485 or RS422.

Name	RS232 Mode	RS485 Mode	RS422 Mode
RXD1 or RX1+	data receiving		data receiving positive
CTS1 or RX1-	clear to send		data receiving negative
A1/RTS1 or TX1+	request to send	RS485_A1	data sending positive
B1/TXD1 or TX1-	data sending	RS485_B1	data sending negative
GND	Ground	Ground	Ground
RXD2 or RX2+	data receiving		data receiving positive
CTS2 or RX2-	clear to send		data receiving negative
A2/RTS2 or TX2+	request to send	RS485_A2	data sending positive
B2/TXD2 or TX2-	data sending	RS485_B2	data sending negative
GND	Ground	Ground	Ground

Ethernet Ports. 5 Ethernet ports, both of them could be configured as WAN or LAN.

LED	Description
Activity	On, blinking
Off	No activity
Link	Off
On	Link on

Reset Button.

Function	Operation
Reboot	Press and hold the RST button for 2~5 seconds under the operating

status.
Restore to default configuration| Press and hold the RST button for 5 ~10 seconds under the operating status.

The RUN

light flashes quickly, and then release the

RST button, and the device will restore to the default configuration.

Restore to factory

configuration

| Once the operation of restoring the default configuration is performed twice

within one minute, the device will restore to the factory default settings.

Digital Input and Relay Output.
Two sets of digital inputs and two sets of relay outputs. Some applications for reference are as below:

Note: When the relay is off, NC is connected to COM, and NO is disconnected. The external power supply input voltage range is DC 5-48V, with a maximum load current of 300mA.

Note: The external power supply DC voltage range is 5V~30V, 0.1A max.

Name	Type	Description
DI1+

Digital I/O

Relay Output

LED Indicators

LED	Description

RUN

| On, solid| Gateway system is initializing
On, blinking| Gateway starts operating
Off| Gateway is powered off

MDM

| Color| With 4G Module:

2G: Red, 3G: Yellow, 4G: Green

Services > Advanced > System >System Settings > User LED Type.

Hardware Installation

SIM Card Installation. Remove the SIM card cover to insert the SIM cards into the device, then screw up the cover.

Note: To ensure optimal performance and compatibility, it is recommended to use 2FF SIM cards that meet industrial-grade standards and feature an integrated design. 2. Antenna Installation. Rotate the antenna into the antenna connector accordingly. 3. Terminal Block Installation. Insert the 4 PIN,5PIN and 6PIN terminal blocks into the interfaces connector, then can connect the devices or sensors to the gateway with wires via corresponding interfaces. 4. Power Supply installation. Insert the power supply cord into the corresponding terminal block if needed, then insert the terminal block into the power connector 5. DIN Rail Mounting. Use 2 M3 screws to fix the DIN rail to the device, then hang the DIN rail on the mounting bracket. 6. Wall Mounting. Use 4 M3 screws to fix the Wall Mounting kit to the device. 7. Grounding the Device. Grounding will help to prevent the noise effect due to electromagnetic interference (EMI). Connect the device to the site ground wire by the grounding screw before powering on.

Connect the gateway’s Ethernet port to a PC with a standard Ethernet cable.
Before logging in, manually configure the PC with a static IP address on the same subnet as the gateway address, click and configure “Use the following IP address”.
To enter the gateway’s web interface, type https://192.168.0.1 into the URL field of your Internet browser.
Use login information shown in the product label when prompted for authentication.
After logging in, the home page of the web interface is displayed, then you can view system information and perform configuration on the device.
The automatic APN selection is ON by default, if need to specify your own APN, please go to the menu Interface->Cellular->Advanced Cellular Setting->General Settings to finish the specific setting.
For more configuration details please refer to RT147_SM_MG460 Software Manual.(END)