LARK 83855 Axton LED 28 inch Black Chandelier Ceiling Light Instruction Manual

LARK 83855 Axton LED 28-inch Black Chandelier Ceiling Light

Product Information

The product is a DR WING 1 – LY 5 4 720. It is a fixture that requires electrical connections for installation. The product is manufactured by LARK and their contact information is as follows:

• Manufacturer: LARK
• Address: 33000 PIN OAK PARKWAY, AVON LAKE, OH 44012
• Website: www.LarkLiving.com

Product Usage Instructions
Indoor Fixtures

1. Connect the positive supply wire (A) to the positive fixture lead (B) using an appropriately sized twist-on connector. Refer to Drawing 1 or 2 for more details.
2. Connect the negative supply wire (C) to the negative fixture lead (D).
3. Refer to the grounding instructions below to complete all electrical connections.

Outdoor Fixtures

1. Connect the positive supply wire (A) to the positive fixture lead (B) using an appropriately sized twist-on connector. Refer to Drawing 2 or 3 for more details.
2. Connect the negative supply wire (C) to the negative fixture lead (D).
3. Cover the open end of connectors with silicone sealant to form a watertight seal. If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If
   the wall surface is lap siding, use caulk and a fixture mounting platform specially designed for lap siding.

Grounding Instructions
Follow the wiring and grounding instructions provided in IS 18. It is important to read and understand these instructions before proceeding with the installation. If new wiring is required, it is recommended to consult a qualified electrician or local authorities
to ensure compliance with code requirements.
Note: The above instructions are provided as an excerpt from the user manual. Please refer to the complete user manual for detailed instructions and safety precautions.

Assembly Instructions

start here

1. Find a clear area in which you can work.
2. Unpack the fixture and glass from the carton.
3. Careful review instructions prior to assembly.

DRAWING 1 – ASSEMBLY

1. To begin assembly take the main body (1) and rotate the arms (A) until they are equally spaced 72 degrees apart and aligned with the opposite arm. Next, rotate the bottom arms until they align with the top arm location – see Drawing 1.
2. Next, determine the height of the fixture that has to be installed. This will determine the number of stems (2) that will be required. If installing over a table 32 to 35 inches above the top surface is recommended.
3. Now take the stems (2) and slip the wires from the fixture through the center of the first stem, slip the stem along the wire, and thread it onto the threaded tube (B) found on the top of the main body (1).
4. Slip on the next stem and thread it onto the first stem, until all stems are installed.
5. Now slide the screw collar loop (3) over the stems. This may have to be removed from the large diameter threaded portion of the swivel assembly (5).
6. Next slide canopy (4) over the stems (2)
7. Now thread wires through the center of the swivel assembly (5) and thread the swivel assembly into the top of the last stem.
8. Now follow the mounting instruction sheet (I.S.19-81) and wiring instructions (IS-18) to complete installation.

SAFETY WARNING
READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN THE POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS. Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture.  The bulb can now be threaded into the socket.

Drawing 1 – Fixture Mounting

Mounting Instructions (IS19-81)

1. Find a clear area in which you can work.
2. Unpack the fixture and glass from the carton.
3. Carefully review instructions prior to assembly.
4.  Shut off the electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.

DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCT- TIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN THE POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS. Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture.

1. To mount assembled pendant body to the ceiling, first, make all the necessary wiring connections using the instruction sheet IS18 provided.

2. After all wiring connections are complete, tuck all wires into junction box (J) – see Drawing 1

3. Now attach the mounting strap (A) to junction box (J) using two screws (B) NOT PROVIDED.
   NOTE: the back of the mounting strap (A) should be flush against the ceiling. It should not be recessed into the ceiling or off the ceiling surface.

4. Next slip canopy (C) up against the ceiling and thread the screw collar (S) onto the exposed portion of the threaded section (L) and tighten to secure the canopy to the ceiling.

Mounting Instructions

Drawing 2 – Chain Hung

Drawing 3 – Post-Mount

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (18) AND ANY ADDITIONAL DIRECTIONS. TURN THE POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTSwiring instructions

Indoor Fixtures

1.  Connect positive supply wire (A) (typically black or smooth, unmarked side or the wo-conduct for cord) to post with appropriately zed twist on the connector – see Drawinas of 2 lead (B)
2. Connect negative supply wire C (typically white or the ribbed, marker side of the two conductor cords) tone to give fixture lead (D).
3. Please refer to the grounding Instructions below to complete all eleanorsconnectons

Outdoor Fixtures

1. Connect positive supply wire (A) (typically bi ack or the smooth unmarked side of the wo-conduc tor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see [Drawings 2 or 3. Connect negs tive supply wreC typically white or their bed. marker side of the two conductor cords) to negative fixture lead (D). cover the open end of connectors with silicone sealant to form a watertight seal. if installing a wall mount fad ure, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. if the wall surface is lap siding. use caulk and a nature mounting platform especially.
2. Please refer to the grounding Instructions below to complete all electrical connections grounding instructions Flush Mount Fixtures For positive ground ing in d ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap in with the ground screw IS – see Drawing Ta
   Note: on straps for screw-supported natures, nest installs the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw

Chain Hung Fixtures
Loop texture grou no wire c typically copper or even plastic cod ted) under the head of the ground screw S) on the fixture mounting strap (M) and connect the loose end of the feature or round wire directly to the ground wire or the building system which appropriately si zed twist- on connectors – see Draw in

Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated to power supply around with an appropriately zed twist-on connector inside the post. Cover the open end of the connector waterfront seal – see Drawing

References

• Lark Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>