Fiik Skateboards Australia Mini FiiK V1 Grommet Electric Skateboard Instruction Manual
- September 7, 2024
- Fiik Skateboards Australia
Table of Contents
Fiik Skateboards Australia Mini FiiK V1 Grommet Electric Skateboard
Product Information
Specifications
- Battery size: 3.7V/300mA
- Charging time: 50% in 20 minutes
- Charging port: Micro USB
- Weight: 55g
- Frequency: 2.4G
- Range: Up to 20M
- Display type: OLED
- Display size: 15mm*22mm
Product Usage Instructions
-
Turning On/Off the Remote Control
To turn on the remote control, press and hold the power button for about 3 seconds until the display screen lights up. To turn off the remote control, press and hold the power button for about 3 seconds until the screen turns off. -
Automatic Turn Off
The remote will turn off automatically in 30 seconds if not connected to the board. -
Display Contents
The display shows various information including power levels, total mileage, current speed, and settings.
FAQ
-
Q: How do I pair the remote with the board?
A: Firstly, turn on the board and then press and hold the power button on the board for 3 seconds to enter pairing mode. Turn on the remote control, and press and hold the Power and Reverse buttons simultaneously for around 1 second to complete pairing. -
Q: What do the different battery indicators mean?
A: The battery indicators show the remaining battery levels for both the board and remote control. For example, 4 bars indicate 100%-75%, 3 bars indicate 75%-50%, and so on.
Thank you for your purchase. Incorrect operation may cause malfunction or even damage to relevant devices, we strongly recommend you carefully read the manual before use and strictly conform to the stated operation process. We will not take any liability arising from the use of the product, including but not limited to the liability for collateral or indirect loss, meanwhile, we will not undertake any liability caused by any changes without authorization. The design, appearance, performance, and operating requirements are subject to change without prior notice.
Overview
Remote Specifications
Specification
|
Parameter
---|---
Battery size| 3.7V/300mA
Charging time| 50% in 20 minutes
Charging port| Micro USB
Weight| 55g
Frequency| 2.4G
Range| Up to 20M
Display type| OLED
Display size| 15mm*22mm
Operating Instruction
-
Turn on the remote control
Press and hold the power button for about 3 seconds till the display screen lights up -
Turn off the remote control
Press and hold the power button for about 3 seconds till the screen turns off -
Automatic turn off
The remote will turn off in 30 seconds automatically if not connected to the board. -
Display contents
The power level of the board, the power level of the remote control, ODO total mileage, trip mileage, current speed, forward/reverse speed setting, and brake set. -
Vibration prompt
- The remote will vibrate once when powered on and off. If the board disconnects, it will vibrate twice.
- It will vibrate once when press the power button and reverse button. The remote will keep vibrating if the throttle roller needs calibration.
-
Calibrating the throttle roller
Turn the remote off. Press and hold both the power button and reverse button at the same time till OK is shown on the screen, this indicates the calibration is complete, if NG is shown, the calibration will need to be re- done. -
Turn on the light
Long press the Reverse button when it turns on, and the light will turn on with one vibration -
Switch forward/reverse
Double-click the Power button, and it will show FW-BW on the screen, remote will vibrate once for forward and twice for reverse. -
Pairing
Firstly, turn on the board and then press and hold the power button on the board for 3 seconds, the light will start flashing to indicate it’s in pairing mode. Turn on the remote control, and press and hold the Power and Reverse button at the same time for around 1 second. Pairing should be complete. -
Board battery indicator
- 4 bars indicate 100%-75%
- 3 bars indicate 75%-50%
- 2 bars indicate 50%-25%
- 1 bar indicates 25%-5%,
The last bar flashing 10%-0%
-
Remote battery indicator
- 4 bars indicate 100%-75%
- 3 bars indicate 75%-50%
- 2 bars indicate 50%-25%
- 1 bar indicates 25%-5%,
Once power is lower than 5%, the remote control can only control the brake and cannot control acceleration.
-
Cruise mode
The cruise control mode is defaulted to 5-50kms, during acceleration, short press the Power button, and CRU will show and enter cruise control mode, push to accelerate and brake, and press the Power button to cancel cruise control mode. -
Accelerate/brake
Push the roller to the front to increase power and then pull it backwards to activate the brake. -
Switching speed
When the board is not moving, short press the Reverse button to switch through the 4 speeds, LO – low speed, MI – medium speed, HI – high speed, and Pro is top speed -
Adjust brake settings
When the board is not moving, pull the roller backward and keep holding, press the Reverse button to switch through the 4 brake settings, B-LO – low brake force, B-MI – medium brake force, B-HI – high brake force, and B-Pro – sports shift. -
Charge the remote control
Micro-USB is used to charge the remote control, the RM icon will indicate the charging status. -
Power protection of remote control
- When the power level is lower than 5%, the throttle will stop working, brakes will still function. The remote will automatically turn off when the power level of the remote control is lower than 1%.
- Note: When the power level of the remote is lower than the last bar, it is recommended for users to charge immediately to avoid any damage caused by lithium battery over-discharging.
-
Loss of signal
If the remote signal is lost, while the remote control is in acceleration, it will stop accelerating and free roll. If the remote is in braking mode, it will continue to brake for 1 second after signal loss, it will not be affected if the remote re-connects within 1 second. After 1 second, if the remote is still not connected the board will free-roll.