GEMBIRD BTSHS-001 Bluetooth Stereo Headset User Manual
- June 8, 2024
- GEMBIRD
Table of Contents
Bluetooth stereo headset
Disclaimer
- We spared no efforts to make sure that the information in this manual is correct and complete. However no liability is accepted for any errors or omissions. Gembird Electronics reserves the right to change the specifications of the hardware and software described in this manual without prior notice.
- No part of this manual may be reproduced, transmitted or translated in any language in any form, by any means, without the prior written permission of Gembird Electronics Ltd.
- Gembird Electronics makes no warranties for damages resulting from corrupted or lost data due to a mistaken operation or malfunction of the product, the software, personal computers or peripheral devices.
Gembird® is a registered trademark of Gembird Europe. Other names or products
not mentioned above may be registered trademarks or trademarks of their
respective owners.
Copyright © 1997-2006 Gembird Electronics Ltd. All rights reserved.
BTSHS-001 User manual
Introduction
Thank you for buying our Bluetooth stereo headset! This manual will help you install it properly.
Features
- Enjoy high-quality stereo music
- Voice dialling
- Last number redial
- Call answering and rejecting
- Clip-on comfortable case
Specifications
- Standard: Bluetooth v.1.2
- Chipset: BlueCore3 Multimedia single chip
- Compatibility: General headset and Bluetooth cell phones
- Radio performance: Class 2
- Carrier frequency: 2.4-2.480GHz
- Sensitivity: <= -75dBm
- Spread spectrum: 10 meters
- Profiles supported: A2DP, headset, hands free
- Charger: input 100-240VAC, output 5VDC
- Battery: rechargeable Li-polymer 120mAh
- Charging time: up to 3hrs
- Talking time: up to 5hrs
- Standby time: up to 150hrs
- Weight: 17g (including battery)
- Dimensions (LxWxH): 50x23x19mm
Package contents
- Bluetooth stereo headset
- Stereo earphones
- Travel charger
- USB charge cable
- User manual
System requirements
Bluetooth enabled computer (with adapter and software driver installed) or mobile phone:
- supporting “Headset” and “Hands free” Bluetooth profiles
- supporting “A2DP” Bluetooth profile for stereo sound
Buttons Descriptions
Please, use your headset according to the following simple steps:
- Charge headset’s battery
- Connect the headset with Bluetooth enabled mobile phone
Charge headset
The headsets have a rechargeable battery inside it. Before using the headset for the first time, we suggest charging the device thoroughly first. Plug the charger into the headset’s electronic socket. The red indicator will flash while charging.
- Charge headset’s battery
- Connect the headset with Bluetooth function mobile phones
The standard charging time: To charge the battery for the first time it
will generally take 3 hours. After recharging completely, the red indicator
light will
turn off. Unplug the charger from the headset. Press down on the multi-
function button for 4 seconds will start the headset. Please read the section
of “Start and close headset”
Conversation, Idle and stereo broadcasts time : After recharging the
battery thoroughly it can run up to 5 hours, stay standby for 150 hours and
has a stereo playing time up to 5 hours. When the battery power is weak:
When the headset is turned on and the power is weak, a red indicator will
flash and send out a beeping sound once every minute. Please refresh the
battery according to the above mentioned step.
Start the headset
Press down multi-function button for 4 seconds. The blue lights gleam quickly
three times and it sends out a beeping sound. A blue indicator will start
flashing.
Attention: Start headset each time, please press the multi-function button
again once. Restart connecting with the headset and mobile phone.
Close the headset
Press down multi-function button for 8 seconds. The blue light gleams quickly
in two times, and there will be a beeping sound. Then the blue indicator will
stop
flashing.
Connecting headset and mobile phone
Before the first use you need to pair the headset with the Bluetooth function mobile phone:
- Put the headset and the mobile phone within the scope of one meter of each other.
- Assure the headset is already closed.
- Press down on the multi-function button for 5 seconds, a red/blue indicator of the headset will flash alternatively.
- Activate the Bluetooth function of the mobile phone according to its user manual.
- Roll over the menu and look for a screen showing Bluetooth equipment and choose the headset.
- Set the pairing key “0000” and press “OK”. After pairing successful, a blue indicator will flash quickly once. You will then hear a beeping sound.
- Press “Return” menu on the mobile phone. The mobile phone screen will show the headset diagram. You can use the headset to dial a telephone number or answer the phone call now.
Attention: When trying to pair the headset and the mobile phone can not
be completed in 2 minutes, the blue indicator of the headset will flash and
then go into idle mode, sending out three beeps. The headset will then turn
off. Please repeat step 2-7.
Answer Calling
When you have an incoming call, the headset will send out a bell ring. Press
the multi-function button: you will answer the phone call such as using the
mobile phone. While listening to stereo music, and you have an incoming phone
call, press the multifunction key once: you can answer the call immediately.
After finishing the conversation, the headset will continue to play music.
Terminate Conversation
Press multi-function once to finish the conversation.
Call Rejecting
If you want to refuse the phone call, you just press down the volume button
for several seconds until hearing 2 beeps.
Latest call re-dialing
Press multi-function button for 3 seconds, you can listen beep sound, at the
same time your mobile phone will pop up the last phone number dialled, press
the multi-function button again for 1 second to call out.
Voice dial
If your mobile phone has the voice dial function, you just need to press the
multi-function button of the headset, a when you hear one beeping sound, you
can then speak.
Attention : The above function is applicable to the mobile phone having
the Bluetooth function. If you want to acquire more information, please read
you’re the user manual of your mobile phone.
Adjust the headset volume
Taping the volume button, and find your volume.
Trouble shooting
If you can not connect the headset and mobile phone, please try the following
steps:
- Insure the headset has been started already and power has been charged enough
- Insure the headset has been paired with the mobile phone already
- The Bluetooth function in the mobile phone has been activated already
- Insure the headset is used within the scope of 10 meters from the mobile phone, and there is no blockage such as a wall or other electronic equipment.
GEMBIRD BTSHS-001 Bluetooth Stereo Headset User Manual – Download
[optimized]
GEMBIRD BTSHS-001 Bluetooth Stereo Headset User Manual –
Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>