GE Profile PFD95GSPWGN, PFD95GSPWDS 7.8 cu. ft. Capacity Smart Front Load Gas Dryer User Manual
- September 7, 2024
- GE Profile
Table of Contents
- GE Profile PFD95GSPWGN, PFD95GSPWDS 7.8 cu. ft. Capacity Smart Front Load
- Product Specifications
- Product Usage Instructions
- INSTALLATION INFORMATION
- SPECIAL INSTALLATION REQUIREMENTS:
- BATHROOM OR BEDROOM INSTALLATION
- DRYER ACCESSORIES
- WARRANTY
- FEATURES AND BENEFITS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GE Profile PFD95GSPWGN, PFD95GSPWDS 7.8 cu. ft. Capacity Smart Front Load
Gas Dryer
Product Specifications
- Model: PFD95GSPWGN/PFD95GSPWDS
- Brand: GE ProfileTM
- Capacity: 7.8 cu. ft.
- Power Rating: 120V, 60Hz, 8A
- Exhaust Options: 4-way via rear, left, right, and bottom (Side Vent Kit required for right, left, and bottom venting options)
- Circuit Requirements: 30-amp circuit breaker or time-delay fuse
- Installation Requirements: Properly grounded branch circuit
Product Usage Instructions
Installation Information
Ensure the dryer wall outlet is within 36 inches of the service cord entry and
accessible when the dryer is mounted in position.
For complete installation instructions, refer to the manual packed with your
dryer.
Special Installation Requirements
- Stacked Installation: Order part no. GFA28KITN for brackets to stack the dryer over a washer.
- Alcove or Closet Installation: Follow specific guidelines for these installations.
- Bathroom or Bedroom Installation: Ensure proper ventilation andclearance.
- Minimum Clearance: Maintain minimum clearances to combustible surfaces on all sides and top. A 1/2-inch clearance on each side is suggested for improved performance.
Dryer Accessories
-
* Metallic Touch-up Paint (Jade Green) – WH97X38418
- Non-Metallic Touch-up Paint (Jade Green) – WH97X38419
Exhaust Length Calculation
- Ensure dryers are exhausted to the outside.
- Avoid terminating exhaust into hazardous areas to prevent fire hazards or damage.
Frequently Asked Questions (FAQ)
Q: What should I do if the dryer is not heating?
A: Check the circuit breaker and ensure the gas supply is connected properly.
If issues persist, contact customer support.
PFD95GSPWGN/PFD95GSPWDS
GE Profile™ 7.8 cu. ft. Capacity Smart Front Load Gas Dryer with Steam and
Sanitize Cycle
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
GAS DRYER RATING
120V| 60Hz, 8A
EXHAUST OPTIONS: 4-way via rear, left, right and bottom.
(The right, left and bottom venting options require Side Vent Kit: GFA28DSVN)
CIRCUIT REQUIREMENTS
An individual, properly grounded branch circuit, protected by a 30-amp circuit
breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36” of service cord entry and
accessible when dryer is mounted in position.
INSTALLATION INFORMATION
For complete information, see installation instructions packed with your dryer.
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
SPECIAL INSTALLATION REQUIREMENTS:
STACKED INSTALLATION
Brackets for stacking dryer over washer are not included with the dryer. Order
part no. GFA28KITN.
ALCOVE OR CLOSET INSTALLATION
-
If your dryer is approved for installation in an alcove or closet,
it will be stated on a label on the dryer back. -
The dryer MUST be exhausted to the outside.
-
Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0” all sides and top.*
-
Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
-
No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION
- The dryer MUST be exhausted to the outside.
- The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATIONS:
Minimum clearances to combustible surfaces 0” all sides and top.*
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
*For improved performance, a 1/2” clearance is suggested on each side.
**Accessories sold separately.
DRYER ACCESSORIES
GE PART NUMBER | DESCRIPTION |
---|---|
WH97X38418 | Metallic Touch-up Paint (Jade Green) 0.6 oz. |
WH97X38419 | Non-Metallic Touch-up Paint (Jade Green) 0.5 oz. pen |
WR97X27706 | Touch-up Paint (Carbon Graphite) 0.6 oz. |
WE02X29449 | Dryer Rack Assembly |
GFA28DSVN | Side Vent Kit |
WE25X20060 | Steam Kit |
WX17X10001CA | Vibration Pads |
GFP1528PWGN | Pedestal (Jade Green) |
GFP1528PTDS | Pedestal (Carbon Graphite) |
GFR0728PWGN | Riser (Jade Green) |
GFR0728PTDS | Riser (Carbon Graphite) |
GFA28KITN | Stacking Kit |
WARRANTY
Labor Warranty | Limited 1-year entire appliance |
---|---|
Parts Warranty | Limited 1-year entire appliance Limited 10-year motor |
PEDESTAL DIMENSIONS (IN INCHES)
The optional 16” pedestal raises the door opening and height of the washer or
dryer.
RISER DIMENSIONS (IN INCHES)
The optional 7” riser raises the door opening and height of the washer or
dryer while remaining ADA-compliant.
DRYER EXHAUSTING INFORMATION – METAL DUCT ONLY
For complete information, see installation instructions packed with your
dryer.
DUCTING MATERIALS
For best performance, this dryer should be vented with 4” diameter all-rigid
metal exhaust duct. If rigid-metal duct cannot be used, then UL-listed
flexible metal (semi-rigid) ducting can be used (Kit PM08X10084 or
PM08X10085). In special installations, it may be necessary to connect the
dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed
flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4”
diameter can be maintained throughout the entire length of the transition
duct. Please see installation instructions packed with your dryer for complete
instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION
- Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
- The maximum length of 4” rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety, do not terminate exhaust into a chimney,
under any enclosed house floor (crawl space), or into an attic, since the
accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back
drafts, bird nesting, etc. The wall cap must also be located at least 12”
above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.
Domestic Dryer Models
| Best Performance
---|---
Maximum length of 4” dia. rigid-metal duct
Exhaust hood type
Number of 90° turns| A
4” opening
| B
2 1/2” opening
0| 90 ft.| 60 ft.
1| 60 ft.| 45 ft.
2| 45 ft.| 35 ft.
3| 35 ft.| 25 ft.
4| 25 ft.| 15 ft.
FEATURES AND BENEFITS
- STEAM SANITIZE – Sterilize clothing with elevated temperatures designed to kill common household germs and bacteria, while using steam technology to reduce wrinkles and odors
- WASHER LINK – Wirelessly link your washer to your dryer so you only have to choose a setting once
- ADAPTIVE MySettings – Through AI Learning, the washer and dryer can personalize your cycle selections automatically
- SMART FEATURES POWERED BY SMARTHQ™ – Start, stop and monitor your laundry from anywhere while receiving real-time notifications and updates
- STAINLESS STEEL DRUM – Enjoy premium durability with a drum that resists rust and helps protect clothes
- WRINKLE CARE – Prevents wrinkles by extending the tumble without heat
- REDUCE STATIC – Prevent static cling with a gentle mist near the end of the cycle
- QUICK DRY – This cycle quickly dries individual items and small loads, making it perfect for families on the go
- DAMP ALERT – Signals when clothes reach the ideal dampness level for ironing or air drying STEAM CYCLES – Refresh small loads and de-wrinkle larger loads with the power of steam
- CHECK VENT NOTIFICATION – Receive a notification when the dryer vent needs to be cleaned, ensuring safe operation and optimal drying performance
- CONVENIENT 4-WAY VENTING – Flexible venting options allow venting from the front, rear or either side
- ENERGY STAR®-QUALIFIED – Meets or exceeds federal guidelines for energy efficiency
- MODEL PFD95GSPWGN – Jade Green
- MODEL PFD95GSPWDS – Carbon Graphite
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>