Ledvion LVS10020 Outdoor Solar LED Lamp Instruction Manual
- September 4, 2024
- Ledvion
Table of Contents
- Ledvion LVS10020 Outdoor Solar LED Lamp
- Superior Features
- Product Image
- Top Specification
- Two Optional Working Modes
- Operations of DIY Work Mode by Remote Control
- Easy Installation
- Operation of Indicator Light
- Wide Applications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Ledvion LVS10020 Outdoor Solar LED Lamp
OUTDOOR – SOLAR LED LAMP
ART.NO. LVSIO020 – LVSI0021
Ledvion
Habraken 1205 5507 TB Veldhoven The Netherlands
www.ledvion.com
Professional, Powerful, Longlasting
Please read and follow all instructions to operate. Save this manual for future reference.
Superior Features
Product Image
Top Specification
Two Optional Working Modes
- Firstly, please press the button on the lamp, lamp turns on and automatically enter Keep Lighting Mode (Default Mode). Press the button again, lamp turns off.
- When the lamp is turned off by pressing the button on lamp, the lamp has no memory. At the same time, the remote control does not work.
Keep Lighting Mode (Default Mode)
Lamp automatically lights up at night and keeps 60% brightness for 3 hours,
after which lamp turns to Sensor Mode.
Sensor Mode
Lamp automatically lights up at night and turns to full brightness when
motion is detected in the range, then turns to 5% brightness in 60 seconds of
no motion.
Operations of DIY Work Mode by Remote Control
- Please remove the insulating film of the remote control before use.
- The remote control can be only workable after the lamp is turned on by pressing the button on the lamp.
- Remote control distance. 6 meters
- Each time you press a button on the remote, the lamp flashes once. When the brightness is adjusted to maximum or minimum, the lamp will no longer flash.
- ON/OFF switch on the remote control has memory function.
Easy Installation
Prepare the lamp, accessories and tools well, confirm the installation location and wire length.
- Drill 2 holes of @8mm with a depth of 60mm on the wall, fix the lamp on the wall with expansion plugs and screws.
- Drill 2 holes of @8mm with a depth of 60mm on the wall, fix the solar panel on the wall with expansion plugs and screws.
- Connect the wire of the solar panel to the lamp and screw it tightly.
- Press the button on the lamp to activate the remote control, then use remote control to set desired working mode
Operation of Indicator Light
This lamp has a RGB indicator light, which shows the charging state of the lamp.
| Indicator Light Status During the Day | Working Status of Solar Lamp |
|---|---|
| Green light isalways on. | Lamp isfully charged. |
| Blue light is flashing. | Solar panel is charging normally. |
| Indicator light isoff. | The current ambient sunlight is too weak to charge the |
lamp.
Indicator Light Status at Night| Working Status of Solar Lamp
---|---
Indicator light is off.| Lamp dischargesand lighting on.
Red light isflashing.| Lamp discharges and lighting on, battery power islow.
Wide Applications
Widely used for construction site, gate, courtyard, corner , garden, industrial area, warehouse, garage, parking lot, roof, factory, pathway, farm, pavilion, countryside, pergola, bus station etc.
Cautions
- This is a solar powered lamp, please install the solar panel in a location where can get enough sunshine.
- Please note the lighting time depends on sunshine duration & working mode.
- The On/Off button on the lamp is power-off switch, helpful to save power consumption. Also the lamp can still get solar charge at day time when the lamp is turned off.
- Built-in intelligent IC is with over-charge and over-discharge protection, safe & durable
- The lamp is equipped with an internal battery pack, which is replaceable. If any need, please contact seller for correct new battery pack.
- Non-professionals please do not disassemble the lamp.
- Please do not dispose the battery with household garbage to avoid explosion.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>