HITWAY BK5 Electric Bike User Guide

HITWAY BK5 Electric Bike

CONFIRM ACCESSORIES

BK5-Parts

1. Pedals
2. Front Reflector
3. Bell
4. Wheel Reflectors
5. 16 in one tool

UNFOLD BIKE

Remove the package, place the whole bicycle on a flat ground, and unfold the frame in the direction of the arrow.

1. Pull up the folder for slotting in the direction of the arrow.
2. Fold the frame in the direction of the arrow.

Adjust the angle of the folding handle, follow the direction shown, squeeze the folding handle of the frame.
Note: If the folding handle of the frame cannot be pressed tightly or too tightly, please adjust the screw at “1” appropriately.

INSTALL HANDLEBARS

1. Open the foldable riser telescopic adjustment buckle.
2. Insert the telescopic vertical pipe in the same direc-tion, adjust the required suitable height, and tighten the adjusting buckle.
Note: If the adjustment buckle is too tight or too loose, please adjust the screw at “3” appropriately.

ADJUST THE FOLDING TUBE

Stand up and close the folded riser in the direction of the arrow in the picture.
After confirming that the quick release slotting is inserted, lift the lever and wrench in the direction of the arrow in the picture.
Press down the folding wrench in the direction of the arrow in the figure,lock the folding riser.
Note: If the folding wrench is too tight or too loose, please adjust the screw at “1” appropriately.

INSTALL THE SEAT TUBE

Pull the seat tube adjust-ment quick release lever in the direction of the arrow in the picture.
Insert the seat tube and adjust to the desired height.
Press the quick release wrench in the direction of the arrow in the figure Note: If the folding wrench is too tight or too loose, please adjust the screw at “1” appropriately.

INSTALL THE BELL

Put the bell bracket into the corresponding position of the handlebar.
Use a Phillips screwdriver to tighten the screws.

INSTALL THE FRONT REFLECTOR

Put the front reflector bracket into the corre-sponding position of the handlebar.
Tighten the screws with a Phillips screwdriver.

INSTALL THE WHEEL REFLECTOR

Pre-assemble the wheel reflector, spacers and screws according to the picture,
Tighten it with No. 4 hex socket and No. 8 open-end wrench.
The operation method of the front and rear wheel reflectors is the same.

INSTALL THE LEFT PEDAL

“L” on the pedal shaft is the left , first of all, turn the pedal shaft counterclock-wise by hand into the crank on the left.Then use a No. 15 open- end wrench to turn counterclockwise to tighten.

INSTALL THE RIGHT PEDAL

“R” on the pedal shaft is the right, first of all,turn the pedal shaft clockwise by hand into the crank on the right.
Then use a No. 15 open-end wrench to turn clockwise to tighten.

POWEL-ON STEPS

1. Insert the key into the key port in picture 1, turn the key to the “ON” position by turning the key to the “OFF” position.
2. Press the switch in Figure 2 to turn on. Otherwise, turn off.

• Insert the key, turn the “OFF” gear to the right and turn it to the “ON” gear.

•  Turn on: Press the switch in the picture.

REAR FENDER SUPPORT ROD FIXING METHOD

1. Use the No. 5 Allen key in the 16-in-1 tool to remove the fixing screws and washers of the fender support rods pre-installed on the left and right sides of the frame, as shown in the picture.
2. Pass the support rod through the fender support rod fixing screw and use a No. 5 Allen key to tighten it into the corresponding screw holes on both sides of the frame, as shown in the picture.

MAINTENANCE CONTACT INFORMATION：

Thank you for choosing us HITWAY. We provide warranty and lifetime after-sales support for our HITWAY products. If you have any questions, please contact our after-sales support team. We will provide you with technical support and suitable solutions as soon as possible.
Email: support@hit-way.com

References

• Way | Find & Reserve Parking, Auto Insurance, Car Wash & More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>