HITWAY H5 Electric Scooter User Manual

HITWAY H5 Electric Scooter

Thank you for your choice, please read this manual before using this product.

Congratulations on your purchase of this new product.
When designing this electric car, I have imagined a new world. In that world, it is an easy decision to leave your scooter behind!
During the design and development of our R & D team for many years, we focused on every detail. We want to make electric scooter a part of your life.
Enjoy, ride and go home safely.

PRODUCT DETAILS

WARNING AND SAFETY

Warning! The responsibility for the repair and maintenance of the electric scooter is assigned to you, which can help you reduce the danger and injury. Reading this manual and following it will help you reduce the risk.

Be careful:

1. Be sure to comply with local traffic laws and regulations.
2. No riding in low visibility.
3. Don’t use the scooter for stunts, wheels, or jumping movements, which will increase your risk of injury and damage to the car.
4. No passengers.
5. Make sure the safety catch and screws are locked and fastened before riding.

Safety Instructions

1. This product can only be used by one person. Do not carry others at the same time.
2. When riding this product, please wear a safety helmet. When riding, please hold the joystick with both hands correctly. It is forbidden to ride with one hand.
3. It is recommended to charge continuously for 6 hours before the first use to maintain the best condition.
4. Please contact in the open area now, and drive after being familiar with the opera­tion of this product.
5. Do not ride this product on unsafe or illegal roads.
6. Do not turn off the power supply while the vehicle is moving.
7. Do not use this product in an environment lower than – 5 °C. Please charge the lithium battery at least once every 30 days when it is not in use.
8. Keep your feet on the scooter when it’s moving.
9. Slow down and drive carefully when passing rough roads.
10. Do not allow the product to be placed in a water depth of more than 5cm or directly impacted by water, which will cause motor and circuit faults.

Tips: When you want to accelerate, lean forward. When you brake, lean back!

OPERATION GUIDE

Battery
Do not operate the motor while charging!
The indicator light on the accelerator shows the power only roughly (full / empty)! Do not store the battery fully charged for a long time (more than two months)!

Do not use the battery if:

1. When damaged
2. When abnormal smell and heat are released
3. When any leakage occurs
   Avoid contact with substances leaked from the battery.
   Batteries should be kept out of the reach of children and pets.
   Exposure to battery voltage can cause death or injury.

Using, storing and charging the electric scooter outside the specified scope will lead to the invalidation of warranty period, battery damage and battery charging invalidity.

GENERAL TROUBLESHOOTING

When the product cannot operate normally, please check whether the following actions have been completed:

1. Power on
2. The power display shows the remaining power
3. The brake has been released
4. All sockets and connectors are clean and connected accurately

If the above actions are completed and the single product still cannot operate normally, please consult the product dealer!!

POWER SWITCH AND KEY

Press the accelerator lightly to speed up the electric scooter.

Warm reminder: Considering the convenience of folding, the ferrule and the shaft are not in a fully tightened state, and there is a gap that is normal. Please rest assured that the driving safety of the vehicle will not be affected. If necessary, you can adjust the tension by yourself: when the handle is folded, fine-tuning the screw clockwise with a 2.5MM hexagonal wrench will loosen the handle, and adjusting it counterclockwise will tighten the handle.

LCD-JX168 INTELLIGENT SPEED CONTROL HANDLE INSTRUCTIONS (SPECIAL FOR

SCOOTER)

Version number: 2016020
Model number: JX-168
Working voltage: 8-B0V compatible

Function

1. Display function
   Speed display, battery indicator, fault indicator, headlight indicator, cruise indicator, gear indicator, total mileage, single mileage, real-time voltage, operating current, operating time, start mode

2. Communication protocol: UART

3. All contents of the display screen (full display within 1 S after power on)

Display content introduction

1. Voltage status level POWER

2. Multifunctional display area
   Total mileage ODO, Single mileage TRIP, Real-time Voltage V, Running current A, Running time TIME, Fault code E

3. In the fault status display area E, when the symbol & is flashing, short press the ON/OFF key to adjust the display interface to the E interface. The corresponding number under this interface represents the corresponding fault content. The specific status is as follows ERRO 1. Motor HAL status
   ERRO 2. Brake failure
   ERRO 6. Undervoltage
   ERRO 7. Motor failure
   ERRO 8. Handlebar malfunction
   ERRO 9. Controller failure
   ERRO 10. Receiving time has timed out
   ERRO 11. Sending failure

4. Speed display area
   Unit MPH, KM/H

5. Gear display area
   Press the MODE button shortly to switch the gears cyclically.
   The higher the gear, the faster the speed. The motor will not run at gear 0

6. Cruise display area
   After the motor is running, keep the speed control handle for 5 seconds and the cruise symbol is on. After releasing the handle, the motor keeps running at the original speed, brake or turn the speed control handle again and return it to the cruise state.

7. Startup method to select display area
   Non-zero start: NON symbol lights up
   Zero start: ZERO symbol lights up

8. USB charging icon display area
   When a data cable is connected to the USB interface of the instrument and draws more than 100 mA of current from it, the USB icon lights up. If the icon is flashing, it means the load is in intermittent charging or the load current exceeds 500 mA, and the USB interface automatically turns on protection mode

9. Parameter setting and definition
   P02: Mileage unit, 0: KM; 1: MILE;
   P04: Sleep time: 0: no sleep; other numbers are sleep time, range: 1-60; unit minute;
   P09: Zero start, non-zero start setting, 0: zero start; 1: non-zero start;
   P16: Instrument real-time cruise function: 1 With this function; 0 Without this function
   P99: One-key recovery function (in the P99 parameter setting interface, press and hold the MODE button for 5-6 seconds, and all parameters are restored to the initial settings of the first startup)
   ODO: ODO reset (in the ODO parameter setting interface, first short press the MODE button and then long press for 5M-6 seconds until the number is zero)

Brief introduction of key functions

1. In the shutdown state, press and hold the power button to turn on, after turning on, press the power button shortly, and the interface will switch between ODO, TRIP, V, A, E, TM,

2. In the power-on state, press and hold the power button to power off.

3. Long press the M key and the power key to enter the mode setting. In the setting interface, short press the power key to switch parameters;
   Short press the M button to change the state of the vehicle speed, the gear shifts from O to the highest gear cyclically
   The gears default to 6 gears, 0 gears motor does not run, 5 gears have the highest speed Parameter value modification:
   Enter the parameter setting to meet, adjust to the parameter you want to adjust, and press the power button and M button to increase
   Increase or decrease the parameter value, after confirming that the modification is complet­ed, long press the power button and M button to exit the parameter setting, and the parame­ter modification will be completed after power off and restart.

4. The rocker arm adjusts the motor speed, moving from top to bottom, the motor speed increases; let go and return to the zero position.

5. Adjust the headlight switch to ON/OFF to control the front light and rear tail light to turn on/off together; Long press the M button for 3 seconds to control the opening and closing of the photosensitive belt on the side of the pedal.

PRODUCT PARAMETERS

Product name: H5
Boundary dimension: 125.531.544cm
Motor power: 48V 800W
Battery capacity: 48v10ah (Customized according to the model)
Standard voltage: 48V
Motor type: Strong brushless motor
Tire size: Solid tyre
Maximum load: 200KG
Battery type: 18650Battery
Vehicle weight: 20KG
Charging time: 4-?h
Brake type: Front and rear disc brake
Maximum speed: 45km/h 1-3 gear free switching
Maximum mileage: 40KM (Rear drum brake)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>