Current WF20 Wall Forms LED Light Instruction Manual
- June 10, 2024
- current
Table of Contents
Current WF20 Wall Forms LED Light
WARNING : Fixtures must be grounded in accordance with local codes or the
National Electrical Code. Failure to do so may result in serious personal
injury.
NOTE : Keep this sheet for future reference
MODEL
Tools Required:
- Flat Blade Screwdriver
- B” Allen Wrench
- G” Socket & Ratchet
- Silicone Based Sealant
Installation
Mounting Plate Installation
Install mounting plate to J-box using screws provided with J-box. Make sure that threaded studs projecting from the plate are horizontally level.
Sealant Application
Apply silicone base sealant (by others) about 1″ away from the mounting plate
to prevent water intrusion.
NOTE : In conformance with UL Standards 1570, 1571, & 1572, a silicone
base sealant must be used between the fixture and supporting wall.
Fixture Housing Installation
Install fixture housing to the mounting plate. (Note orientation label on inside of the housing.) Pull electrical wires into the housing. Press housing to wall, rocking gently to seal caulking. Use flange nuts to tighten the housing to wall. Do not over tighten.
Component Mounting Plate Installation
- Connect wires i.e.; green-to-ground, white-to-common, and black-to-voltage.
- Install component mounting plate using the 10-32 screws provided in housing (4 places). Pay special attention to orientation of WF22
Lamp Installation
- Make certain electricity is OFF before starting lamp installation.
- Screw the proper lamp (as per the fixture label on the housing) into the socket and tighten the lamp sufficiently to ensure a vibration-safe installation.
- After tightening, gently adjust both horizontal and vertical lamp positions so the lamp is centered in the fixture.
Face Frame Installation
- Mount face frame to housing with socket head screws provided. Tighten securely to prevent water infiltration.
Note : The “normal” orientation of types WF21 & WF22 is with the light directed down
WARNING:
This H.I.D. / Fluorescent fixture utilizes a lamp that may contain mercury.
For information on the disposal of lamps, go to the website:
www.lamprecycle.org
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim Products, are warranted to be free from defects of material and/or workmanship for a period of 1 year from date of sale, with the following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers) provided by and/or included in Kim Products shall carry the component manufacturer’s warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted against defects of material and/or workmanship, and failure due to corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall be warranted against defects of material and/or workmanship, and failure due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil, shall be warranted against defects of material and/or workmanship for a period of 3 years from date of sale. Aluminum fixture components in direct contact with soil shall be warranted from defects of material and failure from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance with
applicable Kim instructions, specifications and accepted trade practices, are
covered by the Kim Warranty. During the warranty period, with proof of
purchase, Kim will repair or replace with the same or similar product, at
Kim’s option, without charge. Labor costs are the owner’s responsibility and
are excluded from this warranty. This warranty is void if the product is
modified, tampered with, misapplied, poorly installed, improperly maintained,
or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the exclusive remedy
of the purchaser. This warranty is in lieu of all other warranties, expressed
or implied, including any implied warranty of fitness for a particular
application. Kim Lighting shall not be liable to the purchaser for indirect or
consequential damages.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your input matters to us.
currentlighting.com/kimlighting
© 2022 HLI Solutions, Inc. All rights reserved. Information and specifications
subject to change without notice. All values are design or typical values when
measured under laboratory conditions.
Rev 08/24/22
95530_wf20_22_ins
P.O. Box 60080
16555 East Gale Ave. City of Industry, California 91716-0080 626/968-5666
FAX 626/330-3861
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>