Verkada CD32 Indoor Outdoor Dome Camera Installation Guide

Verkada CD32 Indoor Outdoor Dome Camera Installation Guide

What’s in the box

• Indoor Camera

• Mount plate (Attached to camera)
  

• Mounting template
  

• 3 M4 x 50mm machine screws, wing nuts, and washers

• 4 M4 x 25mm PH2 wall screws

• 4 Wall anchors
  

• T10 Security Torx screwdriver
  

What you’ll need

• A working Internet connection
• 802.3af Power over Ethernet (PoE) switch, or a PoE injector. For operation below -20° C, use 802.3at PoE.
• A smartphone or laptop
• A #2 Phillips screwdriver or power drill with a #2 Phillips driver bit
• 1/4 inch (6.5mm) drill bit for wall anchors
• 1/8 inch (3mm) drill bit for pilot holes
• A Cat5 or Cat6 Ethernet cable with a 0.2-0.25 inch outside diameter (5-6.5mm)

Placement

Mount the camera on a wall or ceiling. Try to keep the camera 8 to 10 feet above the ground.

For best night vision, avoid overhangs or obstructions. These may reflect the camera’s IR illumination and reduce the image clarity in night mode.

Connect

For easy registration and setup, scan the QR code on the product.

If you prefer to manually register your product, please proceed to: verkada.com/start

LED Behaviors

Regular operation

Solid Orange
Camera is on and booting up.

Flashing Orange
Camera is updating firmware.

Solid Blue
Camera is running, connected, and recording data.

Flashing Blue
Generic network error. Contact support.

Network errors
The LED will flash in a specific order, depending on the error state. You will see 1 blue flash, followed by a number of orange flashes.

1 Blue, 1 Orange
Camera is connected with PoE, but unable to connect to the Switch.

1 Blue, 2 Orange
Camera has not received an IP address.

1 Blue, 3 Orange
Camera is not able reach the configured Gateway.

1 Blue, 4 Orange
Camera has detected duplicate IP addresses on the LAN.

Example of 1 Blue, 5 Orange flash sequence

1 Blue, 5 Orange
Camera is not able to resolve Verkada hostnames.

1 Blue, 6 Orange
Camera is not able to receive a response from the NTP Server.

1 Blue, 7 Orange
Camera is not able to certify the SSL connection, likely due to SSL inspection.

1 Blue, 8 Orange
Verkada endpoints are not reachable after boot up

Assembly

Please keep the protective film adhered to the clear bubble until completing the final step of installation.

Use the provided T10 Security Torx security screwdriver to loosen the screws and lift the cover

Connect the camera to an 802.3af/at Power over Ethernet port on your network.

The status LED will turn orange to indicate the camera has power. The LED will turn blue to indicate the camera is active. See additional LED states and definitions under LED Behavior.

Gently pull the cable through the through-hole so it has some slack, but will not interfere with the top cover.

Pulling the Ethernet cable too tight will strain the cable which may impact data performance.

Too much slack in the Ethernet cable may create top cover installation issues.

Mounting

1. Use the provided T10 security torx security screwdriver to loosen the screws and lift the cover. To remove the mount plate, loosen the mount plate screws and twist the camera counter-clockwise. Lift the camera vertically off the base plate and set aside.
2. Use the provided mounting template to mark wall mount holes. For a junction box mount, use the mounting template to determine the correct hole pattern.
3. For a solid material like wood or metal, drill 1/8 inch pilot holes. Drive mounting screws directly into the pilot holes.
4. For drywall, drill 1/4 inch holes. Insert plastic anchors into holes and drive mounting screws into anchors.
5. To secure the camera, place it over the mount plate screws and twist counter-clockwise. Tighten the mount plate screws with a Phillips screwdriver.

Adjust

Adjust your camera to the desired viewing angle. Use the online stream to confirm image orientation.

Image can be flipped 180˚ online in Command.

Default image orientation is indicated by markings on the lens face. Video orientation is also adjustable from within the Verkada application.

Secure

After positioning your camera correctly, align the top shell security holes with the baseplate and place the top shell back into its original position. Tighten the security screws using the provided T10 security torx screwdriver.

Remove plastic film after top cover is secured.

Caution

1. Maintenance and repair work must always be carried out by qualified technical personnel. Disconnect power from the unit when performing a maintenance task.
2. Wiring methods used for the connection of the equipment to earth shall be in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part 1, CSA C22.1.
3. The product must be installed and protected in a location that is not easily accessible and is away from impacts or heavy vibration.
4. The device is only to be connected to PoE networks without routing to outside plants.
5. If powered by a power adapter, the adapter should be properly grounded.
6. Please contact certified dealers for power adapters.

PoE Adapter
To reduce potential safety issues, only use the PoE adapter provided with the product, a replacement PoE adapter provided by Verkada, or a PoE adapter purchased as an accessory from Verkada.

Support

Thank you for purchasing this Verkada product. If for any reason you’re experiencing issues or need assistance, please contact our 24/7 Technical Support Team immediately.

Sincerely,
The Verkada Team
verkada.com/support

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
sales@verkada.com

All specifications are subject to change without notice Copyright © Verkada Inc. All rights reserved.

References

• Verkada
• Verkada
• Verkada Global Technical Support
• Verkada Global Technical Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>