PAJ VEHICLE Finder 4G 1.0 GPS Tracker User Manual
- June 13, 2024
- PAJ
Table of Contents
- Scope of delivery
- Product description
- Activation
- Start up
- Installation
- Turning on
- Use
- Meaning of the LED lights
- Technical details
- Safety instructions
- Declaration of conformity
- Packaging disposal
- Disposal of used batteries
- Meaning of the battery symbols
- Disposal of electrical devices
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PAJ VEHICLE Finder 4G 1.0 GPS Tracker
Scope of delivery
Included in the delivery:
- PAJ VEHICLE Finder 4G 1.0
- An M2M SIM card*
*the M2M SIM card is already inserted and not replaceable!
Product description
120 g
123 x 66 x 16 mm
Activation
NOTE!
Note! In order to proceed with activation you will need the device ID. Please
write this number down before installing your FINDER.
In order to start using your VEHICLE Finder 1.0, first you will have to
activate it online. Please enter the following link www.start.finder-
portal.com …or simply scan the shown QR
code and follow the instructions.
Start up
The moment you successfully activate your device; you can start your FINDER. Please observe the following points before connecting the device to the vehicle battery.
- SIM card is already in the VEHICLE Finder 1.0
- The VEHICLE Finder 1.0 should not be attached to fuel lines or other combustible components.
- No other components of your vehicle should be damaged by the attachment.
- When installing the VEHICLE Finder 1.0 and therefore connecting it to your vehicle’s battery, beware that in order to supply your device with sufficient power, your vehicle’s battery may discharge. If the battery is intact and you are regularly on the road, this should not happen as your vehicle’s battery will be recharged constantly while driving. If this were not the case, check whether your battery is equipped with protection against battery discharge before connecting your VEHICLE Finder 1.0 and retrofit it if necessary. In standby mode, the Finder will need from 10 to 20 mA approximately.
**** Please always observe the manufacturer’s specifications for your vehicle. Compensation claims due to incorrect connections are hereby excluded.
Installation
- Installation Mount the FINDER on the vehicle battery using the adhesive strips.
- Connect the device to the battery. Connect the red cable with the fuse toPLUS (+). Connect the black cable to MINUS (-).
NOTE!
When connected to the power supply, the Vehicle Finder 1.0 switches on
immediately and the LED lights emit a signal. If the FINDER is not connected
to the vehicle battery, but at a different point (e.g. fuse box), this can
result in the ignition on / off function not being accurately recognized.
ATTENTION! The poles must never be reversed
Turning on
After a successful activation you can switch on the VEHICLE Finder 1.0. By connecting the FINDER to the power supply the device has already been switched on.
It is recommended to start VEHICLE Finder 1.0 for the first time in places where the vehicle is not covered (not in the garage or similar)
Use
As soon as you have successfully completed your FINDER’s activation and installed it correctly, the device will be transmitting the first data set. After this, you will be able to visualise your FINDER’s real time location and its travelled routes on a mobile device or your PC. Use our App or enter the following link to do so.
|
---|---
**** The Portal will support you step by step with the help of its functions.
Meaning of the LED lights
Red/orange LED – GSM Status
Signal | Meaning |
---|---|
The red/orange LED is blinking | There is no available GSM signal |
The red/orange LED is off | The GPS Tracker is in standby mode or switched off |
The red/orange LED is fixed | A GSM signal is available |
Blue LED – GPS Status
Signal | Meaning |
---|---|
The blue LED is blinking | There is no available GPS signal |
The blue LED is off | The GPS Tracker is in standby mode or switched off |
The blue LED is fixed | A GPS signal is available |
Technical details
Dimensions| without mounting: 109 x 66 x 16 mm
without cable with mounting: 123 x 66 x 16 mm
without cable (cable length: 40 cm)
---|---
GPS accuracy| Under 10 meters
Battery| High temperature NiMH, 3.6 V, 200 mAh
Weight| 120 g
Time to start| Cold start: 30 s Standby: 30 s
In operation: 1 s
Network/Band| LTE-FDD:
B1/B2/B3/B4/B5/B7/B8/B12/B13/ B18/B19/B20/B25/B26/B28/B66/
LTE-TDD: B34/B38/B39/B40/B41 GSM/GPRS/EDGE: 850/900/1800/1900 MHz
GPS chip| AT6558R
GSM/GPRS module| SIMCOM A7670G
GPS reception| -162 dBm
External battery connection| DC 9-75 V
Storage temperature| from -30°C to +80°C
Operating environment| from -20°C to +75°C
Air humidity| 10 % – 85 %
Waterproof| waterproof according to IP67
Safety instructions
Signal words
The following signal words are used in these operating instructions:
NOTE!
This signal word is used to draw your attention to an issue or situation.
It also serves as a recommendation for proper use. Possible damage to property
or personal injury can be prevented if this is observed.
WARNING!
This classifies a hazard of medium risk level. Failure to observe the warning may result in serious injury or damage.
Proper use
Please read these safety instructions for this GPS tracker carefully before using it for the first time in order to use it properly. The intended use of the GPS Tracker to locate an object or a living being is only that described in this manual. Please note that it is a criminal offence to monitor third parties using a GPS tracker without their consent. If you use it in any other way, it will be considered improper and may result in damage to property or even personal injury. Please note that the GPS Tracker is not a child‘s toy. In other countries and regions there are different laws concerning digital positioning and tracking of people, animals and/or objects. PAJ UG cannot be held responsible if such laws or regulations are violated. The user is held solely responsible for this.
Note!
**** The manufacturer and dealer accept no liability for damage caused by
improper or incorrect use.
Security
**WARNING! RISK OF ELECTRIC SHOCK!**
Faulty electrical installation or excessive voltage can lead to electric shock. Before use, check the voltage of the external battery against the specification on the type plate. If you no – tice any visible damage to your GPS Tracker or the cable, do not use it and contact our support team. Only use the original parts supplied. Never place the GPS Tracker near open flames or hot surfaces. The GPS Tracker is waterproof according to IP67. However, we recommend using it in dry environments if possible. The cable should be connected and routed carefully and professionally. Keep it away from moisture and do not bend it. Do not open the housing of the GPS tracker. Leave repairs to qualified specialists. If you carry out repairs yourself, connect the GPS Tracker improperly or operate it incorrectly, liability and warranty claims are excluded.
Hazards for children and vulnerable people
WARNING! RISK OF SUFFOCATION!
Please do not allow the GPS Tracker to be used unsupervised by people (including children) with reduced physical, sensory or mental capabilities. The exception is if they have been instructed beforehand by the person responsible for their safety of how to use the appliance. Make sure that your child does not handle small parts (e.g. accessories, etc.). These can be swallowed and lead to suffocation
NOTE! Inform your child about the dangers and use of the GPS tracker.
The Battery
WARNING! EXPLOSION AND FIRE HAZARD!
In the following, you will find information and instructions on how to handle the battery: The GPS Tracker is powered by a NiMH battery. This is not replaceable and must not be removed or opened. Make sure that the GPS Tracker is kept away from heat sources and high temperatures, such as direct sunlight. Failure to observe this warning may result in destruction of the battery and overheating, explosion and fire. Make sure that the GPS Tracker is properly connected to the vehicle and that appropriate restrictions (e.g., volt specifications) are taken into account. Failure to do so could result in overheating, explosion or fire. Do not burn or puncture the GPS Tracker. Protect it from mechanical damage. Do not remove, drop, disassemble or modify the battery with sharp or pointed objects. If a child swallows the battery, seek medical help immediately! Removing or replacing the battery
- Contact our support if the battery needs to be removed or replaced.
- Send the machine to use to remove or replace the battery.
- For safety reasons, do not attempt to remove the battery. Failure to remove the battery properly may result in damage to the battery and unit, personal injury and/or compromise the safety of the unit.
- PAJ GPS shall not be liable for any damage or loss (whether in contract or tort, including negligence) arising from your failure to comply with these warnings and instructions.
WARNING! RISK OF CHEMICAL BURNS!
Batteries that leak due to damage can cause burns in contact with the skin. Therefore, never open the battery. However, if the battery leaks, please wear protective gloves.
Electromagnetic compatibility
Please observe all prohibitions and switch off the GPS tracker immediately in dangerous areas and if it can cause interference. It should not be used near, for example, medical equipment, fuels and chemicals, or in blasting areas. Mobile devices may cause interference that can affect performance. Transformers and very strong magnetic fields must be avoided. Otherwise, deviations in the transmission may occur.
Note!
Failure to observe these recommendations may result in malfunctions or damage
to the GPS tracker.
Cleaning
WARNING! RISK OF DAMAGE!
In the following you will find information and instructions on how to clean the GPS tracker. Do not use aggressive cleaning agents or brushes. Do not clean the GPS Tracker with cleaning objects (e.g. knives, metal sponges). This can damage the surface. Never put the GPS Tracker into water, in a dishwasher (or similar) and do not use a steam cleaner. The surface can be wiped with a slightly damp cloth. The GPS Tracker should be wiped completely dry afterwards.
Storage
If you are not going to use the GPS Tracker for a long period of time, switch it off. Place the tracker in its original packaging or in a same size box. Protect the tracker from dirt and moisture.
Note!
Keep the FINDER away of children’s reach in order to avoid possible damage to
property or personal injury.
Declaration of conformity
Hereby, PAJ UG (haftungsbeschränkt) declares that the tracker, VEHICLE Finder 4G 1.0, is in conformity with the Directive 2014/53/EU. The complete text of the EU Declaration of Conformity can be found at the following Internet address: paj-gps.de/konformitaetserklaerung/
Packaging disposal
Dispose of the packaging according to type. Throw cardboard and paper to the corresponding container. Foil belongs in the recyclables collection.
Disposal of used batteries
The following note is addressed to those who use batteries or products with
products with built-in batteries and who will not resell them in the form in
which they were supplied to them (end users).
Free recall of used batteries. Batteries must not be disposed of with waste.
You are legally obliged to return used batteries so that proper disposal can
be guaranteed. You can return used batteries to a local collection point or to
your local retailer. As a distributor of batteries, we are also to take back
used batteries, although our obligation to take back used is limited to the
type which we carry or have carried as batteries in our range. Used batteries
of the aforementioned type can therefore either be returned to us with
sufficient postage or handed in directly to our dispatch warehouse at the
following address free of charge:
PAJ UG (haftungsbeschränkt)
Hohe Straße 61
51570 Windeck
Deutschland
E-Mail: info@paj-gps.de
Meaning of the battery symbols
Batteries are marked with the symbol of a crossed-out dustbin (see illustration). This symbol indicates that batteries must not be disposed of in household waste. Batteries containing more than 0.0005% mercury by mass, more than 0.002% cadmium by mass or more than 0.004% lead by mass are also marked with the chemical name of the pollutant below the dustbin symbol. The abbreviation „Cd“ stands for cadmium, „Pb“ for lead and „Hg“ for mercury
Disposal of electrical devices
The Electrical and Electronic Equipment Act (ElektroG) contains a large number of requirements for the handling of electrical and electronic equipment. The most important ones are summarised here.
-
Separate collection of WEEE
Waste Electrical and Electronic Equipment that has become waste is referred to as WEEE. Owners of WEEE must dispose of it separately from unsorted local waste. In particular, WEEE does not belong in household waste, but in special collection and return systems. -
Batteries and accumulators
As a rule, owners of WEEE must separate spent batteries and accumulators that are not enclosed in the WEEE before handing them over at a collection point. This does not apply if the WEEE is handed over to public waste management authorities and separated from other WEEE there for the purpose of preparation for reuse. -
Options for returning old appliances (WEEE)
Owners of WEEE from private households can hand it in to public waste management authorities or at the collection points set up by manufacturers or distributors as defined by the ElektroG. An online directory of collection and collection points can be found here: https://www.ear-system.de/ear-verzeichnis /sammel-und-ruecknahmestellen.jsf -
Data Protection
Old equipment often contains sensitive personal data. This applies in particular to information and telecommunication technology devices such as computers and smartphones. For your own sake, please note that each end-user is responsible for deleting the data on the old equipment to be disposed of. -
Meaning of the „crossed-out dustbin“ symbol
The symbol of a crossed-out dustbin regularly displayed on electrical and electronic equipment indicates that the respective device must be separated from unsorted local waste at the end of its service life. -
Manufacturer registration number
As a manufacturer, within the meaning of the ElektroG, we are registered with the responsible foundation Elektro-Altgeräte Register (Benno Strauß-Str. 1, 90763 Fürth) under the following registration number: DE33887550
DO YOU HAVE ANY QUESTIONS?
In this case, please contact us and we will be delighted to help you!
PAJ UG (haftungsbeschränkt)
Hohe Straße 61
51570 Windeck
Germany
Mail: info@paj-gps.de
Telefon: +49 (0) 2292 39 499 59
Web: www.paj-gps.com
DO YOU HAVE ANY QUESTIONS?
The PAJ GPS Team wishes you to enjoy your VEHICLE Finder 4G 1.0!
References
- Laufpunk – Laufen. Abenteuer. Emotionen. | Wearables, Smartwatches, Trends für Sportler und Aktive
- GPS Tracker kaufen - PAJ
- Alle Anleitungen von PAJ - Hier zum Downloaden
- Konformitätserklärung | ► PAJ GPS
- Konformitätserklärung | ► PAJ GPS
- Konformitätserklärung | ► PAJ GPS
- GPS Vehicle Tracker and Mobile App - PAJ GPS
- GPS Tracker kaufen - PAJ
- GPS Tracker kaufen - PAJ
- Alle Anleitungen von PAJ - Hier zum Downloaden
- Localizadores GPS: Protege lo que amas - PAJ GPS España
- Traceurs GPS: Protégez ce qui compte - PAJ GPS France
- Localizzatori GPS: Proteggi ciò che ami - PAJ GPS Italia
- Localizadores GPS: Proteja o que você ama - PAJ GPS Portugal
- PAJ-GPS FINDER Portal – Aktivieren Sie Ihren FINDER von PAJ
- PAJ-Portal
- stiftung elektro-altgeräte register
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>