ergotron MXV Desk Mount Monitor Arm User Manual
- June 4, 2024
- ERGOTRON
Table of Contents
ergotron MXV Desk Mount Monitor Arm
Safety
Hazard Symbols Review
These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the signifi cance of the following Safety Hazards if encountered on the product or within the documentation. Children who are not able to recognize and respond appropriately to Safety Alerts should not use this product without adult supervision!
| Symbol | Signal Word | Level of Hazard |
|---|---|---|
 |
||
| NOTE | A NOTE indicates important information that helps you make better use of |
this product.
| CAUTION| A CAUTION indicates either potential damage to hardware or loss of
data and tells you how to avoid the problem.
| WARNING| A WARNING indicates either potential for property damage, personal
injury, or death.
| Important! You will need to adjust this product after installation is
complete. Make sure all your equipment is properly installed on the product
before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are
too easy or diffi cult or if product does not stay in desired positions,
follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice
a diff erence. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat
these adjustment steps to ensure safe and optimum operation.
---|---
| Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure mounting surface is strong enough to handle
mounted product and equipment.
---|---
| Caution:
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury.
---|---
CAUTION: DO NOT rotate monitor past rear edge of desk. Doing so will create an unstable situation and may cause equipment damage or personal injury.
Features & Specifications
Components
Tools Needed
Mounting
How to replace rotation stop screws (Arms must be straight up)
*Optional longer screws can be added for thinner desks:
NOTE: VESA plate will only accept 75mm or 100mm VESA pattern.
WARNING! Stored Energy Hazard: The Riser mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the Riser has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
**4** NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow
the cable routing instructions in this manual. Failure to follow these
instructions may result in equipment damage or personal injury.
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
**a** Lift – Up and down
**b** Tilt – Forward and Backward
CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.
b Tilt – Forward and Backward
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE: When contacting customer service, reference the serial number.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>