Aseptico AEU-6000 Implant Motor and Surgical Motor User Guide

: August 21, 2024
: Aseptico

Table of Contents

Manual Operation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AEU-6000-70V & AEU-6000 Quick
Reference Guide

Manual Operation

Select handpiece ratio:
– 1:5, 1:3, 1:2, 1:1, or 20:1 Ratios – Unit automatically switches to Implant Mode
– 8:1 Ratio – Unit automatically switches toEndo Mode.
Select speed, torque setting and irrigationsetting by using the up/down buttons.
Select Motor Direction
Select Torque: Auto Stop (Green Light) Maximum (Orange Light) Limiting (No Lights)
Select Flow On/Off

Preset Operation:

Select Preset by pressing one of the buttons numbered 1-5

Changing Presets:

Select desired handpiece ratio, speed, torque, and irrigation settings as indicated above in Manual Operation.
Press and hold Preset button where you want new settings to be stored.
Follow Prompt:
– “Save To Preset (#)?”
Press Preset button #1 (YES)
Observe Confirmation:
– “Preset (#) Setting Saved”

NOTE: Software Version: Appears briefly when unit is turned on.
Calibrating Handpiece

Preselect ratio of handpiece being calibrated by using Ratio Up/Down buttons:
(Note: Unit switches to Implant Mode when 1:5, 1:3, 1:2, 1:1, or 20:1 ratios are selected or Endo Mode when 8:1 ratio is selected.)
Insert a file, bur, or drill into the handpiece.
Press CAL button .
Follow Prompts:
– “Add Handpiece to Motor”
Press Preset button #1 (NEXT).
– “Free Run in Progress, Please Wait…”
– “Calibration Successful!, The Result is Saved” …OR:
– “Calibration Failed!”
Press Preset button #1 (RETRY), or button #3 (EXIT)

Installing new software (takes 30 seconds):

Turn off unit
Pull back blue plug from slot and insert new software memory card.
Turn unit On
“Memory Card Detected. Re-program?”
Press Preset Button #1 (YES) to install new program.
“Presets will be erased. Continue?” Press button #1 (YES).
“Programming successful. Eject card.”
System reboots.

Variable Foot Control Functions

Allows for variable speed up to the speed set on the display.
Four hands-free buttons ensure greater infection control:
Orange: Steps between the Preset buttons.
Yellow: Changes micromotor direction.
Lavender: Increases torque with each consecutive press of pad, up to 5 increments — 6th press of pad returns to original setting.
Teal: Water pump On/Off. Press and hold pad to cycle through flow in 10% increments.
Use the attached handle to easily reposition the foot control.

Cleaning

Console: Wipe the console with a soft cloth and mild detergent or a 10% bleach solution (1 part household bleach to 9 parts water).
Motor: Autoclave according to the included instructions.
Handpiece: Spray with lubricant/cleaner and autoclave according to the included instructions.
Silicone tubing: Autoclave according to the included instructions.

Restoring Factory Defaults

Turn main power switch OFF.
Wait two seconds, then turn main power switch back ON.
As the Aseptico startup marquee scrolls across display screen, press and hold the Calibration (CAL) button.
At the “Recall Factory Setup?” prompt, press Preset Button #1 (Yes) to restore factory defaults, then when asked, press the #1 Button again to confirm. A beep will sound.
(NOTE: All customized Presets will be lost when factory defaults are restored.)

Select 20:1 Handpiece Type

Repeat first 3 Steps above under “Restoring Factory Defaults”.
Repeat 4th Step above under “Restoring Factory Defaults”, EXCEPT press Preset Button #3 (No) at the “Recall Factory Setup” prompt.
A “Select 20:1 Handpiece” prompt will display* . Press Button #1 or #2 to select either Mont Blanc® , Eco Line®, , Impulsion® , or AHP-85-SS handpiece.
The System will confirm the handpiece selection then automatically restart with the selected handpiece enabled. “MB”, “ECO”, “IMP” or “SS” will display beneath the 20:1 ratio indicator.

Mont Blanc® and Impulsion® are registered trademarks of Anthogyr. Eco Line® is a registered trademarks of MK Dent.
( *) The System will also allow the user to select either Mont Blanc® , Impulsion® , Eco Line® or AHP-85-SS 20:1 handpiece settings when: the System is turned on the first time; after factory settings are recalled; or, after the System is reprogrammed with the memory card.

P.O. Box 1548 • Woodinville, WA 98072
PN:420827 Rev-I ECO 15761 07/23