GE Profile PFD95GSPWGN 7.8 Feet Capacity Smart Front Load Gas Dryer Instruction Manual

GE Profile PFD95GSPWGN 7.8 Feet Capacity Smart Front Load Gas Dryer

Product Specifications

• Model : PFD95GSPWGN/PFD95GSPWDS
• Brand : GE ProfileTM
• Capacity : 7.8 cu. ft.
• Power Rating : 120V 60Hz, 8A
• Exhaust Options : 4-way via rear, left, right, and bottom
• Circuit Requirements : 30-amp circuit breaker or time-delay fuse

Installation Instructions

Stacked Installation:
Brackets for stacking dryer over washer not included. Order part no. GFA28KITN.

Alcove or Closet Installation:

• Follow general installation instructions.
• Bathroom or Bedroom Installation:
• Follow general installation instructions with additional ventilation considerations.

Minimum Clearance:
Minimum clearances to combustible surfaces on all sides and top. For better performance, 1/2″ clearance on each side is recommended.

Accessories

• Metallic Touch-up Paint (Jade Green) – WH97X38418
• Non-Metallic Touch-up Paint (Jade Green) – WH97X38419
• Vibration Pads – WE25X20060
• Pedestal (Jade Green) – GFP1528PWGN

Exhaust Length Calculation:

1. The maximum length of 4 rigid ducts tolerated is determined by the manufacturer.
2. Dryers must be exhausted to the outside to prevent fire hazards and damage.
3. Do not terminate exhaust into a chimney, enclosed house floor, attic, common duct, or plenum with a kitchen exhaust.

PFD95GSPWGN/PFD95GSPWDS
GE Profile 7.8 cu. ft. Capacity Smart Front Load Gas Dryer with Steam and Sanitize Cycle

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

• GAS DRYER RATING 120V : 60Hz, 8A
• EXHAUST OPTIONS : 4-way via rear, left, right, and bottom. (The right, left, and bottom venting options require Side Vent Kit: GFA28DSVN)
• CIRCUIT REQUIREMENTS : An individual, properly grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.

NOTE : The dryer wall outlet must be located within 36” of the service cord entry and accessible when the dryer is mounted in position.

INSTALLATION INFORMATION

For complete information, see the installation instructions packed with your dryer.

ADA-Compliant

With leveling legs retracted : 39-3/4” (101 cm).
With leveling legs fully extended : 40-5/8” (103.1 cm).

SPECIAL INSTALLATION REQUIREMENTS

STACKED INSTALLATION
Brackets for stacking the dryer over the washer are not included with the dryer. Order part no. GFA28KITN.

ALCOVE OR CLOSET INSTALLATION

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer’s back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between the dryer cabinet and adjacent walls or other surfaces are 0” on all sides and top.*
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

BATHROOM OR BEDROOM INSTALLATION

• The dryer MUST be exhausted to the outside.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATIONS : Minimum clearances to combustible surfaces 0” all sides and top.*
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.

1. For improved performance, a 1/2” clearance is suggested on each side.
2. Accessories are sold separately.

DRYER ACCESSORIES

WARRANTY

PEDESTAL DIMENSIONS (IN INCHES)
The optional 16” pedestal raises the door opening and height of the washer or dryer.

RISER DIMENSIONS (IN INCHES)
The optional 7” riser raises the door opening and height of the washer or dryer while remaining ADA-compliant.

DRYER EXHAUSTING INFORMATION

METAL DUCT ONLY
For complete information, see the installation instructions packed with your dryer.

DUCTING MATERIALS
For best performance, this dryer should be vented with a 4” diameter all- rigid metal exhaust duct. If rigid-metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit PM08X10084 or PM08X10085). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see the installation instructions packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

EXHAUST LENGTH CALCULATION

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of the dryer, add one turn.
2. The maximum length of 4” rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turnover of 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

CAUTION
For personal safety, do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampened wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12” above the ground or any other obstruction with the opening pointed down.

FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.

Domestic Dryer Models

| Best Performance
---|---
Maximum length of 4” dia. rigid-metal duct
Exhaust hood type
Number of 90° turns| A

4” opening

| B

2 1/2” opening

0| 90 ft.| 60 ft.
1| 60 ft.| 45 ft.
2| 45 ft.| 35 ft.
3| 35 ft.| 25 ft.
4| 25 ft.| 15 ft.

FEATURES AND BENEFITS

• STEAM SANITIZE
   Sterilize clothing with elevated temperatures designed to kill common household germs and bacteria, while using steam technology to reduce wrinkles and odors

• WASHER LINK
  Wirelessly link your washer to your dryer so you only have to choose a setting once

• ADAPTIVE My Settings
   Through AI Learning, the washer and dryer can personalize your cycle selections automatically

• SMART FEATURES POWERED BY SMARTHQ
  Start, stop, and monitor your laundry from anywhere while receiving real- time notifications and updates

• STAINLESS STEEL DRUM
   Enjoy premium durability with a drum that resists rust and helps protect clothes

• WRINKLE CARE
  Prevents wrinkles by extending the tumble without heat

• REDUCE STATIC
  Prevent static cling with a gentle mist near the end of the cycle

• QUICK DRY
  This cycle quickly dries individual items and small loads, making it perfect for families on the go

• DAMP ALERT
  Signals when clothes reach the ideal dampness level for ironing or air drying STEAM CYCLES – Refresh small loads and de-wrinkle larger loads with the power of steam

• CHECK VENT NOTIFICATION
  Receive a notification when the dryer vent needs to be cleaned, ensuring safe operation and optimal drying performance

• CONVENIENT 4-WAY VENTING
  Flexible venting options allow venting from the front, rear or either side

• ENERGY STAR-QUALIFIED
  Meets or exceeds federal guidelines for energy efficiency

• MODEL PFD95GSPWGN
  Jade Green

• MODEL PFD95GSPWDS
  Carbon Graphite

For answers to your Monogram, Café, GE Profile, or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center Service, at 800.626.2000.

FAQ’S

Q: What should I do if my dryer is not heating?
A: Check the gas supply, ensure the circuit breaker is on, and clean the lint filter. If the issue persists, contact customer service.

Q: Can I stack this dryer without additional parts?
A: No, you need to order part no. GFA28KITN for stacked installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>