eve 51ECI1704 Shutter Switch Instruction Manual

: August 21, 2024
: eve

Table of Contents

Meet Eve Shutter Switch
Get Started
Installation
Disassembly
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

51ECI1704 Shutter Switch
Instruction Manual

Meet Eve Shutter Switch

Voltage: 230 V~ 50 / 60 Hz
max. connected load: 750 VA
max. load current: 6 A (max. 5 A per channel)
Connection terminals: 1.5 mm² rigid wire
Flush-mounted socket dimension: ø 60 mm, min. 35 mm depth
Ambient temperature: -10 °C to 50 °C
Operating humidity: max. 85%, non-condensed
Protection rating: IP20
Frequency range: 2402 – 2480 MHz (BLE) / 2405 – 2480 MHz (Thread)
RF Power: max. 12 dBm (EIRP)

Get Started

CAUTION – Risk of electric shock!
Only authorized electricians may connect, install and set up Eve Shutter Switch.
Before installation, ensure the system is disconnected from the power supply!
Eve Shutter Switch is used to directly switch permanently connected electrical loads with a supply voltage of 230 V~. Eve Shutter Switch is designed for use in household and similar fixed installations. Before installation, ensure suitability by reviewing the technical data and the operating conditions.
Eve Shutter Switch must not be used in conjunction with life-support systems or other devices that could put the life or health of humans and animals at risk or risk property damage.
Installation – Preparation
In your fuse box, switch off the fuse connected to your shutter switch. Press the buttons on your current shutter switch a few times to make sure that there is no current flowing.

Installation

Remove your current shutter switch
Loosen your existing shutter switch and pull it out. Note the current wiring and take a photo of it if necessary. You can usually tell which line is the current-carrying input (L) and which lines leads to the shutter by the direction from which the cables are led into the box and by the inscription on your current shutter switch.
Eve Shutter Switch can only be installed if there is a neutral line (N, usually blue) in your outlet. Remember which line is connected to the input on your current shutter switch (L), for example by marking it with adhesive tape. Then disconnect the existing wiring and remove your current shutter switch.
Connect Eve Shutter Switch

: Shutter up
: Shutter down
L: Outer conductor / phase (current-carrying line)
N: Neutral line

Eve Shutter Switch requires that a neutral line is connected. If the outlet is not equipped with a neutral line, Eve Shutter Switch is incompatible with this outlet.
Eve Shutter Switch does not require a connection to a protective conductor / ground wire (PE, usually green/yellow). Mounting

Place the switch unit in the flush-mounted socket and secure it with the 3.2 x 25 mm screws (included).
Place the supplied or your existing frame on the switch unit and secure it with the fixing frame.
Press the switch plates onto the switch unit.
In your fuse box, switch on the fuse dedicated to the circuit of that shutter switch. You should now be able to move your shutter by pressing Eve Shutter Switch.

Setup

Download the Eve app from the App Store.
Open the Eve app and tap Add Accessories. Eve will now guide you through the setup process.
If you already have Eve set up, open Eve settings and add Eve Shutter Switch.

To add Eve Shutter Switch, use the HomeKit code on the back of this manual.
Enjoy
Operate your shutter using the app or a Siri voice command. You can also operate your shutter directly via Eve Shutter Switch. Reset
Remove the left switch plate by pulling down this switch plate from top edge. Press both left buttons simultaneously for 10 seconds.

Disassembly

In your fuse box, switch off the fuse connected to your shutter switch.
Make sure that there is no current flowing by pressing the buttons on Eve Shutter Switch a few times.
Remove the switch plates by pulling down each rocker switch evenly from top edge.
Remove the fixing frame and remove the frame.
You can now remove the switch unit from your flush-mounted socket and disconnect the cables.

Happily connected?
Write a review and tell your friends
Stay in touch and discover more via:
Facebook facebook.com/meeteve
X @meeteve
Eve Newsletter evehome.com/newsletter
YouTube @MeetEve
Instagram @meet_eve
Eve Blog blog.evehome.com
Legal Information
This device conforms to the general requirements and further relevant provisions of the 2014/53/EC directive. You can download the declaration of conformity from www.evehome.com/doc.
Something amiss?
Reach out now: Visit our knowledge base or contact our support team
help.evehome.com
evehome.com/contact
Please keep your HomeKit Setup Code in a safe place. You need it to securely add Eve to your home, and nobody but you has a copy.