baseus SECURITY S1 2K Outdoor Camera User Guide
- August 19, 2024
- baseus SECURITY
Table of Contents
**baseus SECURITY S1 2K Outdoor Camera User Guide
**
PRODUCT SPECIFICATIONS
- S1 Camera
- Resolution: 2304×1296
- Night Vision: color night vision
- Input: 5V⎓2A (Max.)
- Waterproof Rating: IP67
COMPONENTS
- Base mounting screw holes
- Camera
- Indicator light
- Motion detection sensor
- MIC
- Spotlight
- Solar panel
- Sync button
- USB-C charging port
- Speaker
PACKAGE INCLUDING
S1 Camera:
-
S1 Camera × 1 (Model No.: S0SW00)
-
Camera Charging Cable×1 (USB-A to USB-C)
-
Screw Mount×1
-
Screw Pack×1
SETUP INSTRUCTIONS
- Download and install the baseus Security APP, and register an account.
- Follow the instructions on the screen to add the camera to your device list.
CAMERA CHARGING
Please fully charge the camera before first use. It takes about 6 hours to charge the camera.
- 5V USB Charger
S1 Outdoor Camera is equipped with a solar panel featuring an advanced sun- powered tracking system*. This innovative system efficiently converts sunlight into electrical energy, ensuring the battery is continuously charged. Should the battery level drop, it typically results from limited sunlight or increased power usage. There’s no need for manual cable charging unless you receive a low battery alert.
*The solar panel, equipped with Baseus Security’s patented sun-powered tracking system, rotates to maximize sunlight absorption. To ensure safety and functionality, maintain adequate space around the panel at all times, preventing contact or collisions with nearby objects during its operation.
CAMERA INSTALLATION
-
Choose a location where you can get the ideal viewing angle. We recommend to mount the camera 7-10 feet (2-3 meters) above the ground.
Recommended installation area:- exterior wall without eaves;
- over the eaves, under 10 feet(3 meters);
- any poles or fences where the sunlight is not blocked.
-
Turn the knob of the mounting bracket counterclockwise to loosen and remove it.
-
Drill holes with a 15/64-inch (6 mm) drill bit and insert expansion bolts into the holes; using expansion bolts is necessary for walls made of hard materials such as concrete, brick, or stucco.
-
Screw the knob of the mounting bracket firmly into the mounting hole.
-
Hold and screw the camera onto the mounting bracket.
Rotate the camera to adjust the viewing angle and check the footage with the live stream in the Baseus Security APP.
*For troubleshooting, check out the help in the Baseus Security APP. See the application page for LED indicator status.
NOTICE
The device is not a toy.
Choking Hazard: The product contains (or comes with) small parts, plastic elements, cables and parts that may cause choking hazard. Keep your camera and its accessories out of the reach of small children. Consult a physician immediately if small parts are swallowed.
Strangulation Hazard: Children get strangled in cords. Keep cords out of the reach of children (more than 3ft/0.9m away).
The suitable temperature for S0SW00 and accessories is -20°C to 50°C (Charging temperature is 0°C to 40°C). When charging, please place the device in an environment that has a normal room temperature and good ventilation.
Unless specifically indicated that it is safe to do so in the user guide or instruction manual, do not use this device in an environment that exceeds the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or instruction manual, avoid exposing your device to direct sunshine or excessively wet environments.
For pluggable equipment, the socket-outlet shall be easily accessible.
Use only the adapter provided by the manufacturer. Using unauthorized adapters may cause danger and violate the authorized use of the device or the warranty article.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSES OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
SAFETY
This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Follow local rules and never dispose of the product with normal household waste.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
ny Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in fixed/mobile
exposure condition. The min separation distance is 20cm.
The following importer is the responsible party (for FCC matters only)
Company Name : BASEUS TECHNOLOGY (US) INC
Address: 421 S BROOKHURST ST SUITE 1312 АNAHEIM, СА 92804
Telephone: +6-145412699
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Shenzhen Baseus Technology Co., Ltd. Declares that the product is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
https: //eu.baseus.com/pages/euro-compliance.
RF exposure notice:
The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.
Frequncy bands and power are as below:
| Model | Function | Operation Frequency | Max. RF Power |
|---|---|---|---|
| S0SW00 | Wi-Fi | 2412-2472MHz | EIRP:17.83dBm |
| Bluetooth | 2402-2480MHz | EIRP:9.63dBm |
WARRANTY
Customer Service
Warranty: 24-month limited warranty
Contact Us
support@baseussecurity.com
https://www.baseus.com
United States ：+1(800) 220 8056
Monday to Friday 10:00 AM -6:00 PM (UTC-5)
For FAQs and more information, please visit
https://www.baseus.com/pages/support-center”
- Facebook @Baseus
- Instagram @baseus_global
- Twitter @Baseus_Global
- YouTube @Baseusofficial
- TikTok @baseusglobal
Warning
Please follow the above safety instructions otherwise it will cause fire, electric shock, damage or other injuries.
https://www.baseus.cn
https://www.baseus.com
service@baseus.com
Add: 2nd Floor, Building B, Baseus Intelligence Park, No.2008, Xuegang Rd,
Gangtou Community, Bantian Street, Longgang District, Shenzhen
Hotline: 400-071-2711(China) / +1 800 220 8056(Global)
Website: https://www.baseus.cn(China) / https://www.baseus.com(Global)
Official After-sales E-mail Address:
service@baseus.com (China) /
care@baseus.com (Global)