PROBRITE SDAY50-MS-5K-BK Solar Daystar Led Light Installation Guide
- June 1, 2024
- PROBRITE
Table of Contents
PROBRITE SDAY50-MS-5K-BK Solar Daystar Led Light
SAFETY INFORMATION
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE NATIONAL
ELECTRICAL CODE AND LOCAL BUILDING CODES BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
PRECAUTIONS
- Please read and understand this entire manual before attempting to assemble, install, or operate this light fixture.
- This light fixture requires no power source other than included solar panel.
- Make sure connections are secure\ using intergyral plug-and-tighten cable connectors.
- This light fixture should be installed\ outdoors to a wall or a wooden pole.
- This solar panel should be installed outdoors with direct sunlight access; Can be mounted on ground, wall or rooftop.
WARNING: Risk of fire. Keep the fixture at least 3 in. (76mm) from
combustible materials.
CAUTION: Burn hazard. Allow the light fixture to cool before touching.
PRE-INSTALLATION
PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture.
SPECIFICATIONS
MODEL | SDAY 50 |
---|---|
Lumens (Light Output) | Up to 4500 Lumens |
Max Watts | 45 Watts |
Lumens/Watts (Efficacy) | 100 Lumens per Watt |
Power Consumption | 21 (M1) / 23 (M2) / 24 (M3) / 8 (M4) / 9 (M5)W |
(integral battery)
Battery Capacity| 9.6V 9000mah
Charging| 8 hrs (solar panel included)
Light Color (CCT)| 5000K
Dimmable (Operated by Remote Control, Excluding mode 4/5)| 20% / 40% /
60% / 80% / 100%
Operation Modes (Operated by Remote Control)| Mode 1: 4Hr Mode
- 450 Lumens for 4 hrs
- 4500 Lumens when motion detected
Mode 2: All-night Mode
- 315 Lumens for 4 hrs
- 90 Lumens for 8 hrs
- 2925 Lumens when motion detected
Mode 3: Energy Saving Mode
- 270 Lumens for 4 hrs
- 90 Lumens for 10 hrs
- 2025 Lumens when motion detected
Mode 4: Motion-only
- 4500 Lumens when motion detected
Mode 5: Occupancy Mode
- First trigger: 2800 Lumens for 20 secs
- Second trigger: 1800 Lumens for 30 mins
- Third trigger: 920 Lumens for 4 hrs
TOOLS REQUIRED
-
Power Drill
-
Wrench
-
Ladder
PACKAGE CONTENTS
Part | Description | Quantity |
---|---|---|
A | Light fixture | 1 |
B | Integral motion sensor | 1 |
C | Integral solar panel | 1 |
D | Mounting tenon | 1 |
E | Remote control | 1 |
(Battery included)
HARDWARE KIT
NOTE: Hardware not shown to actual size
Part | Description | Quantity |
---|---|---|
AA | Hex head screws | 3 |
BB | Set screws | 4 |
CC | Allen Key | 1 |
WALL MOUNT INSTALLATION
-
FOR BEST RESULTS
CAUTION: Do not tamper with motion sensor as it is wired into fixture.- When mounting the fixture, ensure the motion sensor (B) has clear line of sight to target area for motion detection.
- Ensure solar panel (C) has direct sunlight exposure.
- Do NOT connect fixture to any wires or power supply.
- Hardware provided to mount fixture to wood. Concrete walls will require alternate hardware (not included).
-
INSTALL MOUNTING TENON TO THE WALL
- Position the mounting tenon (D) as shown in (Fig 1).
- Drill 3 holes as shown in (Fig 1).
- Attach tenon firmly to wall with hex head screws(AA).
-
MOUNTING THE FIXTURE TO THE WALL
- Align the fixture onto to the tenon (Fig 2).
- Secure the light fixture to the mounting tenon by tightening set screws (BB).
OPERATION
REMOTE CONTROL OPERATION
MODES OF OPERATION
(Operate at maximum of 25ft from the fixture)
SELECT MODE WITH REMOTE CONTROL
OPTION 1: 4 HOURS MODE (M1)
4 HOURS MODE enables the light fixture to turn ON for 4 hours at 450 lumens
ambient light. Upon motion detection, light emits 4500 lumens for security
lighting.
- Once this mode is selected it will remain in the current mode until the fixture is manually turned off through the remote control.
- Dimming will be proportionate to the lumens (450) in the selected mode, until the fixture is manually turned off or a new mode has been selected.
OPTION 2: ALL-NIGHT MODE (M2)
ALL-NIGHT MODE enables the light fixture to turn on for first 4 hours at 315
lumens, followed by 8 hours at 90 lumens for lighting through out the night
Upon motion detection, light emits 2925 lumens.
- Once this mode is selected, it will remain in the current mode until the fixture is manually turned off through the remote control.
- Dimming will be proportionate to the lumens (315, 90) in the selected mode, until the fixture is manually turned off or a new mode has been selected.
OPTION 3: ENERGY-SAVING MODE (M3)
ENERGY-SAVING MODE enables the light fixture to turn on for first 4 hours at
270 lumens, followed by 10 hours at 90 lumens to conserve the battery. Upon
motion detection, light emits 2025 lumens.
- Once this mode is selected, it will remain in the current mode until the fixture is manually turned off through the remote control.
- Dimming will be proportionate to the lumens (270, 90) in the selected mode, until the fixture is manually turned off or a new mode has been selected.
OPTION 4: MOTION-ONLY MODE (M4)
MOTION-ONLY MODE enables the light fixture to turn on ONLY when motion is detected. Upon motion detection, light emits 4500 lumens for maximum security lighting.
- Once this mode is selected, it will remain in the current mode until the fixture is manually turned off through the remote control.
- Dimming is unavailable in this mode.
OPTION 5: OCCUPANCY MODE (M5)
OCCUPANCY MODE enables the light fixture to turn on ONLY when motion is detected:
- 1st trigger: 2800 lumens for 20 seconds
- 2nd trigger: 1800 lumens for 30 minutes
- 3rd trigger: 920 lumens for 4 hours
- Once this mode is selected, it will remain in the current mode until the fixture is manually turned off through the remote control.
- Dimming is unavailable in this mode.
MANUAL OPERATION
ON-FIXTURE CONTROLS:
- Power – depress button on right of motion sensor for ON/OFF operation.
- Depress button on left of motion sensor for Mode. Continue pressing button until desired Mode is achieved.
CARE AND CLEANING
- Clean the solar panel with clear water and a soft damp cloth on a regular basis to ensure batteries can fully charge.
- To prolong the original appearance of the light fixture clean with clear water and a soft, damp cloth only.
- Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints, solvents, or any other chemicals on this light fixture. They could cause a premature deterioration of the finish and may void the warranty.
- Do not spray the light fixture with a hose or power washer.
TROUBLE SHOOTING
Problem | Possible Cause | Solution |
---|---|---|
Light does not turn ON | Low battery | Check the power meter on the |
integral motion sensor. If red, the battery needs to be charged for 8 hours
before use.
Check that cable connection is secure. Ensure the solar panel has exposure to
sunlight and that there is no debris covering the solar panel.
No motion detected| Check if the motion sensor is blocked by obstacle or dirt.
Remote control unresponsive| Low battery on the remote| Replace the
battery cell (3V Lithium CRV2032) on the remote.
Angle and distance| Turn the light OFF and ON under different angles and
distances.
Light not bright enough| Wrong mode selected| Turn the light OFF and ON
again to select a mode with higher output.
Light cycles ON and OFF continuously| Motion sensor is faulty| Clean the
motion sensor with a damp, clean cloth. If the problem persists, please
contact customer service.
LIMITED WARRANTY
This is a limited warranty offered by Probrite for one year from the date of purchase to its customers. Probrite warrants to customers that the product will be free from defects in material and workmanship. The obligation of Probrite under this warranty is limited to the provision of replacement of product and is extended to the original purchaser of the product on presenting valid purchase receipt or other proof of date of original purchase acceptable to Probrite. The receipt is required for rendering the warranty performance. Any warranty claims without original proof of purchase would not be accepted.
It should be noted that the warranty does not apply to Probrite products that have been altered or repaired by unauthorized personnel, have been subjected to neglect, abuse, misuse or accident or damages caused during shipping. Any other products not manufactured by Probrite which have been supplied, installed and/or used in conjunction with Probrite products are not covered under this warranty. Any damages caused by replacements bulbs, LEDs or corrosion or discoloration of brass components are also not covered by this warranty.
LIMITATION OF LIABILITY:
In no event Probrite shall be liable for indirect, consequential, incidental
or special damages, or lost profits. Probrite is not liable for any claims or
damage arising out of or connected with the manufacture, sale, delivery, use,
maintenance and repair or modification of Probrite products, or supply of any
replacement parts that exceed the purchase price of Probrite products, giving
rise to a claim. Labor charges to remove or install the fixtures will not be
accepted.
TO CLAIM:
Please contact PROBRITE customer service at
1-844-507-5651 or email
support@PROBRITE.com and include your name,
address and contact number, along with a copy of the purchase receipt and a
brief description of the problem.
CUSTOMERS SUPPORT
Questions? / Problems? / Missing Parts? / Need Accessories?
Before returing to the store, call or email PROBRITE
Customer Service 9am-5pm EST Monday to Friday.
1-844-507-5651
support@PROBRITE.com
PROBRITE.COM
RETAIN THIS MANUAL FOR FUTURE USE
Para las translaciones en español,
visit www.probrite.com/install
PROBRITE.COM
Please call 1-844-507-5651 or email
support@probrite.com for further assistance
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>