HOFFREE HOGC-RGL203 Gaming Chair User Manual
- August 19, 2024
- HOFFREE
Table of Contents
HOFFREE HOGC-RGL203 Gaming Chair
Product Information
Specifications:
- Model : M5x10mm
- Quantity : 1
Product Usage Instructions:
- Ensure the equipment is turned off before installation.
- Locate the M5x10mm component and carefully handle it for installation.
- Follow the specific installation steps corresponding to the numbers provided in the manual (11, 12, Nx1, 13, 14).
- If interference occurs during installation, follow these steps:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- If interference persists, consult the dealer or an experienced radio/TV technician for assistance.
- Ensure compliance with FCC rules related to harmful interference and RF exposure.
PACKING LIST
INSTALLATION
Note : All screws have been preassembled the accessories Please remove them from the accessories before assembling
FUNCTIONS OF EACH BUTTON
- Long press the setting key to enter the setting mode
- MODE+/- adjust the lighting part (left/right side of backrest/entire seat cushion)
- SPEED+/- to adjust the number of lamp beads (cannot be adjusted when the light strips are fully on, only when part of the light strips are on, the number of lamp beads can be increased or decreased)
USAGES
Testing
|
o n sly pre UTO” 5 ti to ente e RGB automatic switc mode,which can test the your LED.
---|---
Matching
|
Pres “LOCK” for 5 seconds until LED flash in green quickly to match the remote control with the receiving controller. Press “LOCK” for 5 seconds untill LED flash in white slowly to unmatch.
Reorder
RGB
|
For different kinds of LED,the RGB keys may don’t perfectly match to your LED, reorder them if needed. Continuously press “SETTING” 5 times until LED flash in white once and then turns into all white, press the “R” until LED is red, press “G” until LED is green, press “B’ untill LED is blue, finally press “SETTING” once to finish your setting.
Adjust the LED quantity
|
Press “SETTING” for 5 seconds until LED flash in white to enter the setup menu. Press “MODE
+/-” or “SPPED+/-” to add/reduce the quantity of the LED pixels.Finally press “SETTING’ once to finish the setting.
TROUBLESHOOTING
| |
---|---|---
The product is shaking and unstable| 1. Wrong screw installation
2. The screw is broken
3. Check that the screws are not tightened in place
| 1. According to the instruction manual, install the correct screw in the correct position
2. To replace, use the included spare screws
3. Tighten the loose screws
The light strip is off| ****
1. Not plugged in
2. The lighting pattern is not saved correctly
| ****
1. Confirm that the product is powered on normally
2. Please read the instructions of the remote control carefully (page 6), and follow the operation
Audio doesn’t work| ****
1. Bluetooth connection failed
2. Bluetooth connection error
| ****
1. Turn on your phone’s bluetooth to connect
2. Turn off the phone’s Bluetooth and reconnect (Bluetooth name: HuaBox)
The remote control not working| ****
1. The remote control gasket is not pulled out and cannot work
2. The battery is in poor contact or the battery is installed backwards
3. The battery is dead
| ****
1. Check whether the remote control gasket is pulled out
2. Check whether the battery is installed incorrectly and adjust
3. Replace the new battery to make the remote control work normally
BLUETOOTH CONNECTION
(bluetooth name HuaBox)
FCC Warning Statement:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FAQ
Q: What should I do if there is interference during installation?
A: If interference occurs, try reorienting or relocating the receiving
antenna, increasing separation between equipment and receiver, connecting to a
different circuit, or seeking professional help.
Q: What are the FCC rules related to this device?
A: The device complies with Part 15 of the FCC Rules. It must not cause
harmful interference and must accept any received interference without
undesired operation.
Q: Can the device be used in portable exposure conditions?
A: Yes, the device has been evaluated to meet general RF exposure requirements
and can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>