ALARM COM ADC-V729 4MP Outdoor Floodlight Camera Installation Guide
- August 18, 2024
- ALARM COM
Table of Contents
ALARM COM ADC-V729 4MP Outdoor Floodlight Camera
Specifications
- Model: 4MP Outdoor Camera Floodlight
- Variants: ADC-V729, ADC-V729AC, VC729P
- Resolution: 4MP
- Outdoor Use: Yes
- Power Source: Wired
- Compatibility: Junction boxes
Product Usage Instructions
Pre-installation Checklist
Ensure you have the necessary tools and components before beginning the
installation.
Mounting the ADC-V729AC
- Switch off the power at the circuit breaker before starting any work to avoid electrical shock.
- Follow local safety codes for installation. In some cases, a professional electrician may be required.
Using the Mounting Bracket
- Screw the mounting bracket into the junction box using the provided screws. Ensure proper orientation based on installation location.
- Secure the mounting bracket to the wall or eave depending on the installation location.
Using the Adapter Plate
- Attach the metal bracket to the junction box using the appropriate screws.
- Secure the mounting bracket to the adapter plate using the designated holes.
Hanging the Camera and Wiring
- Insert the T hook wire into the hole at the bottom of the mounting bracket for hanging.
- Ensure the fixture is securely positioned before releasing it.
- Pull the cables through the center hole to prepare for wiring.
Wire, Mount, and Power the ADC-V729AC
Confirm all knobs and collars are tightly secured for stable positioning of
the camera and lights.
FAQ
-
Q: When should I use the adapter plate?
A: Use the adapter plate when installing on a junction box where screw locations overlap with mounting plate screws. -
Q: What should I do if I encounter a rare situation during installation?
A: In such cases, use just the mounting bracket for installation unless necessary to use the adapter plate.
4MP Outdoor Camera Floodlight (ADC-V729/V729AC/VC729P) -Installation Guide
Pre-installation checklist
When using the ADC-V729AC:
- ADC-V729AC camera
- Mounting hardware (included)
- Broadband (Cable, DSL, or Fiber Optic) internet connection with router
- Wi-Fi enabled computer or mobile device
Note: If the router does not have the WPS button, you will need the case- sensitive SSID (wireless network name) and the network WPA or WEP key (if the encryption is enabled at the router).
In the box
In the unit
- 1 set (x2) of M4 7/16 screws to attach the floodlight base to the mounting bracket
- 1 set (x2) of weatherproof caps to seal the unit after install
Screw bags
Multiple screw sizes are included to accommodate multiple junction box and
screw hole sizes. Choose which set to use based on your particular install
requirements. The following screws are included for mounting:
- (4) #8-32 X 7/8” – for attaching the mounting bracket to the wall/junction box
- (4) #8-32 X 1/2” – for attaching the mounting bracket to the wall/junction box
- (2) 6-32 X 1”, – for attaching the adapter plate to the mounting bracket
- (2) 6-32 X ½ – for attaching the adapter plate to the mounting bracket
- Set of wall anchors and screws (V729DC and VC729P only)
- Camera base to mounting bracket grounding wire and nut
Overview
Requirements
- Ensure the unit is properly grounded.
- The ADC-V729AC must be installed on a weatherproof junction box (not included in the box).
Requirements for the ADC-V729AC ∧
Caution : There is a risk of electrical shock when installing the ADC-
V729AC. Ensure the power is off at the circuit breaker before doing any work.
Ensure you follow local safety codes for installation. In certain locations, a
professional electrician must perform the installation.
- The ADC-V729AC must be installed on a weatherproof junction box (not included in the box).
- Connect the fixture to a 100-240VAC 50/60 Hz power source. Wire connection should be using gauge range 14-18 AWG and rated to Min. temperature 80°C. Ensure you follow local safety codes.
- Ensure the unit is properly grounded.
- For best results, we recommend a junction box that meets these specifications (junction box not included):
- A 4-inch round/square junction box (the base of the 729 is 5.9 inches)
- Weatherproof
- Outdoor rated
- Remove any existing light fixture and metal bracket on the junction box.
Mount the ADC-V729AC
Caution : There is a risk of electrical shock when installing the ADC-
V729AC. Ensure the power is off at the circuit breaker before doing any work.
Mounting recommendations
Note : For optimal PIR motion detection performance, it is recommended to
install the ADC-V729 at a height of eight feet with the camera pointed
downwards at a 30° angle.
When to use the adapter plate:
If installing on a junction box where the only screw location is overlapping
with mounting plate screws, use the adapter plate.
Note: This should be a rare situation. Use just the mounting bracket in
all other cases.
To install on the ceiling:
With the ball joint exposed to the front, flip the camera and lights 180°. The
adapter should be installed with the camera in front of the floodlights with
the arrow on the back pointing towards the wall.
To install using the mounting bracket:
Note: This is the most common installation type.
- Screw the mounting bracket into the junction box using the appropriate set of screws. Ensure the mounting bracket is in the proper orientation.
- If installing the camera on the wall, the hook should face the floor.
- If installing the camera on an eave, the hook should face the wall.
- Ensure the mounting bracket is secure to the wall.
To install using the adapter plate:
- Screw the metal bracket to the junction box using the appropriate set of screws via the long edge. Be sure to align it with the flat side facing the junction box.
- Screw the mounting bracket to the adapter plate using the holes in the mounting bracket circle.
To hang the camera and prepare for wiring:
- Put the T hook wire into the hole on the bottom of the mounting bracket to allow the fixture to hang from the mounting bracket.
- Ensure the fixture is secure before releasing it.
- Pull the cables through the center hole to prepare for wiring.
Wire, mount, and power the ADC-V729AC
Caution: For secure positioning, confirm that all knobs and collars are
firmly tightened. The lights and camera should not be left loose and should
not allow for any motion when the camera is mounted.
To wire, mount, and power the ADC-V729AC:
Caution: There is a risk of electrical shock when installing the ADC-
V729AC. Ensure the power is off at the circuit breaker before doing any work.
To wire the ADC-V729AC:
- Connect the neutral green wire to connect to the corresponding ground wire. Use the included wire nut to secure the wires together.
- Connect the white wire to the corresponding neutral white wire. Use the included wire nut to secure the wires together.
- Connect the black wire (hot) to the corresponding black wire. Use the included wire nut to secure the wires together.
- Gently pull on the wires to ensure they are secure.
To mount the ADC-V729AC:
- Push the wires back into the junction box.
- Disconnect the hook and align it along the bottom of the unit, or place the hook with the wires in the junction box.
- Align the two holes on the back of the floodlight base with the metal poles.
- For HWV 0104+ the mounting screws come captive in the unit. To install the unit on the mounting bracket for HWV 0104:
- Remove the weatherproof caps.
- Align the two holes on the back of the floodlight base with the metal poles and push the unit into bracket.
- Screw in the unit using the captive screws inside it.
- Insert the weatherproof caps.
- For HWV 0103 or earlier:
- Align the two holes on the back of the floodlight base with the metal poles.
- Screw in the unit using the included black screws.
- Insert the weatherproof caps.
- Screw in the unit using the included black screws.
- Insert the weatherproof caps.
To power the ADC-V729AC:
- Switch on the breaker.
- The camera’s LED should light up red after a few seconds. Wait for the camera’s LED to start blinking white before proceeding.
Connect and enroll the ADC-V729AC
Note: The ADC-V729P is not compatible with Wi-Fi and must be connected
via Ethernet.
Add the device to the customer account by selecting the account in the
MobileTech app, then selecting the camera from the video device list or
entering its MAC address. For more information about enrolling
Alarm.com cameras to a customer account, see Enroll a
camera or video device to a customer account.
Using AP mode:
- Once powered up, the camera’s LED will begin to blink white. If the LED is not white after two minutes, press and hold the WPS/Reset button and release when the LED begins to blink white (about 6 seconds).
- On an Internet-enabled device, connect to the Wi-Fi network ADC-V729 (XX:XX:XX) where XX:XX:XX is the last six characters of the ADC-V729’s MAC address, which is located on the camera or on the packaging.
- On the same device, open a web browser and enter 192.168.1.1 in the URL field. Follow the on-screen instructions to add the ADC-V729 to the Wi-Fi network. The LED will briefly turn red before blinking green. The LED will be solid green when the connection is complete.
- Add the device to the account by either selecting the account in the MobileTech app or by using a web browser and entering the following web address: www.alarm.com/addcamera (you will need the customer username and password).
- Select the camera from the video device list or enter its MAC address to begin adding the camera. The MAC address is located on the camera or on the packaging.
Follow the on-screen instructions to finish adding the camera.
Using WPS
- Once powered up, the camera’s LED will begin to blink white. Press and hold the WPS/Reset button and release when the LED begins to blink blue (about 3 seconds).
- Activate WPS mode on the router. The camera will begin to connect to the Wi-Fi network. The LED will be solid green when the connection is complete.
- Add the device to the customer account by either selecting the account in the MobileTech app or by using a web browser and entering the following web address: www.alarm.com/addcamera (you will need the customer user name and password).
- Select the camera from the video device list or enter its MAC address to begin adding the camera. The MAC address is located on the camera or on the packaging.
Follow the on-screen instructions to finish adding the camera.
LED reference guide
Troubleshooting
- If you have issues connecting the camera to the account, power cycle the camera and try again.
- If issues persist, reset the camera to factory defaults. Press and hold the WPS/Reset button until the LED is flashing green and red (about 15 seconds), then release the button. The camera will reboot to factory default.
Important If the camera was previously installed on a different
Alarm.com account, it will need to be deleted before it
can be installed again.
Notices
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause unwanted behaviors.
- Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- FCC ID: YL6-1438852R
ICES
- This Class B digital apparatus complies with Canadian ICES-003.
- This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
- This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the equipment and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Please contact intsupport@alarm.com for more information on Canadian RF exposure compliance.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Floodlight_Camera_(ADC-V729%2F%2FV729AC%2F%2FVC729P)/4MP_Outdoor_Camera_Floodlight_(ADC-V729%2F%2FV729AC%2F%2FVC729P)_-_Installation_Guide
Updated: Tue, 06 Aug 2024 18:15:46 GMT
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>