ALARM COM ADC-VDB780B Wireless Video Doorbell Installation Guide

: June 5, 2024
: ALARM COM

Table of Contents

In the Box
Pre-Installation Checklist
Installation
- Lower on the Wireless Video Doorbell
- Mount the Wireless Video Doorbell
Charging The Battery
LED Guide
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**ALARM COM ADC-VDB780B Wireless Video Doorbell Installation Guide

**

Use this guide to assist with the installation of your ADC-VDB780B Wireless Video Doorbell.

In the Box

ADC-VDB780B Wireless Video Doorbell
ADC-VDB780B mounting plate
Battery with charging cable
Mounting screws (2)
Mounting anchors (2)
Quick start guide

We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept”, you consent to the use of ALL the cookies. However you may visit Cookie Settings to provide a controlled consent. Cookie settings ACCEPT

Pre-Installation Checklist

ADC-VDB780B and included accessories
Drill/Screwdriver
Level
Pencil

An installed Alarm.com Smart Chime (ADC-W115C) – if you have not installed the Alarm.com must be completed before you can proceed with the installation of your doorbell. Wi-Fi connection to broadband (Cable, DSL, or Fiber Optic) internet A computer, tablet, or smartphone with Wi-Fi

**The Alarm.com Smart Chime (ADC-W115C) is required for installation.

**

Installation

Lower on the Wireless Video Doorbell

Remove the Wireless Video Doorbell (VDB780B) from the packaging.
Separate the battery pack from the VDB780B body.
Press the doorbell button on the front of the battery. If the LED alternates between red and blue, to completing the installation.
If the LED isn’t alternating blue and red, reconnect the battery pack to the VDB780B body.
After the button LED stops flashing red, press and release the doorbell button and ensure the LED.

Connect the Wireless Video Doorbell to the Alarm.com Smart Chime

Insure the Wireless Video Doorbell (VDB780B) is less than 10 feet away from the Alarm.com Smart Chim

Confirm that the W115C has been installed and associated with an account.
To enable WPS mode, press and hold the VDB780B doorbell button firmly for greater than 30 second.
Press the WPS button located on the side of the W115C to enable WPS mode. The WPS LED will be
If the pairing is successful, the W115C Devices LED will quickly blink 3 times, and the VDB780B LED.
Follow the on-screen instructions to finish adding the device.

Mount the Wireless Video Doorbell

an, Level, & Mark

Identify a location on the side of your doorframe to mount your Wireless Video Doorbell (VDB780B above the ground for an optimal field of view.
Place the mount at your desired location.
Use a level to ensure the mount is parallel with the ground.
Use a pencil to mark the two holes of the mount.

Up: If you have someone to help you with the setup, use the Mobile App or Customer Website to start our planned mounting position to assess the field of view before you start drilling.

Attach the Wireless Video Doorbell to the Mount

Align the prongs on the back of the Wireless Video Doorbell (VDB780B) with the 4 rectangular slots
Push the VDB780B into the slots and slide down, until the device clicks into place.
Slide the latch on the bottom of the mount to secure the VDB780B in place.

Confirm Battery Charge

If the battery was not fully charged as part of the Power on the Wireless Video Doorbell section instructions in the Charging the Battery section.

Charging The Battery

Separate the battery pack from the VDB780B body.
Plug in the Micro USB charger to a wall outlet and connect it to the battery.
The charging LED, located on the top of the battery pack, will be solid orange while the device is when charging has completed.

LED Guide

Button light guide

perational States

off = Camera in standby mode (normal operation) or battery is drained and requires recharging

Blinking red = Power on, camera booting
Blinking yellow = Camera power cycling
Alternating red and green = Camera resetting to factory default
Alternating red and blue = Low battery – recharge required
Solid green = Connected to Alarm.com LAN Connection
Solid red = No local or Internet connection
Rapidly Flashing yellow = Firmware Upgrade

Charging States

LED display is located on the top of the device Battery pack must be removed and plugged in

Solid orange = Charging
Solid green = Fully Charged

Additional states communicated by the main button LED

Blinking red/white = charging failure, ensure the battery is being charged with an appropriate power so Charges please contact Alarm.com.

Blinking red rapidly = battery is overheated, please charge in an indoor environment

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuan Designed to provide reasonable protection against harmful interference in a residential installation. This Frequency energy and, if not installed and used in accordance with the instructions, may cause harmful ere is no guarantee that interference will not occur in a particular installation. If this equipment does c
ception, which can be determined by turning the equipment off and on, the user is encouraged to try Following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connecte
Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party responsible for complian Equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenn SA/Canada market, only channel 1-11 can be operated. Selection of other channels is not possible.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set fort Should be installed and operated with minimum distance 20cm between the radiator & your body.

We use cookies on our website to give you the most relevTerms & Conditions ant experience by remem | bePrivacy Policy ring your preferences and repeat visits. By clicking “Accept”, you consent to the use of ALL the cookies.
However you may visit Cookie Settings to provide a controlled consent.