VOVO USA TCB-9100WA Integrated Smart Bidet Toilet Installation Guide
- August 18, 2024
- VOVO USA
Table of Contents
VOVO USA TCB-9100WA Integrated Smart Bidet Toilet
Product Information
Specifications
- Model: 660
- Dimensions: 390mm x 660mm x 550mm (15.35″ x 25.98″ x 21.65″)
Product Usage Instructions
Extract Bad Water Before Installation:
Before installing the product, follow these steps to extract any bad water:
- Direct the supply hose end into a 3-gallon (11.4L) or larger bucket.
- Ensure that the supply stop can provide a minimum of 1.5 gallons (5.7L) or more in 10 seconds.
- Shut off the water supply before proceeding to the next step.
Frequently Asked Questions (FAQ)
-
Q: What should I do if the supply stop cannot provide the required flow rate?
A: If the supply stop does not meet the minimum flow rate of 1.5 gallons (5.7L) in 10 seconds, check for any blockages or restrictions in the hose or supply line. Ensure that the water pressure is adequate before proceeding with installation. -
Q: How often should I extract bad water before installation?
A: It is recommended to extract bad water each time before installing the product to ensure optimal performance and prevent any potential issues due to contaminants in the water lines.
Installation Manual
Cautions before Installation (This may differ from the product specification.)
Installation
- Secure enough installation space in the bathroom and check whether it disturbs the bathroom door.
Space
- Secure water outlet at least 100mm away from the floor.
- It can cause the discoloration of wall.
E-mail : support@vovousa.com
Water Pressure
- Minimum 1.5 kgf/cm2 (0.15 MPa) water pressure is required. If the pressure is not secured, please be aware that the flushing may not work properly to discharge the dirt.
- Even if other modifiers are used at the same time, it still requires more than the minimum required water pressure. The maximum water pressure is 7.5 kgf/cm2 (0.75 MPa).
Extract bad water before install
- Direct the supply hose end into a 3 gal (11.4L)or larger bucket
- Make sure that the supply stop can provide a minimum of 1.5gal (5.7L)or more in 10 seconds.
- Shut off the water supply.
- Proceed to next step
Drawing for Installation (unit : mm/in)
FAQ
-
Q: What is electrical requirements? Is it energy efficient?
A : 6~10 Amps at 120V, 60 Hz is necessary for this item. A separate circuit breaker is recommended. It has a power save mode which uses least amount of energy. -
Q: Power save LED light is keep flashing. (Turned off and on)
A : Please open the valve, please check the water has entered to the bidet. If it still flashes, please try reset. (Unplug the cord and plug it back after 30 seconds) -
Q: How long is the cord?
A : 4ft (1.2m).
Please open the seat and the lid when you reset the bidet toilet
Installation Accessories
- A type Installation Accessories (Standard)
- Recommended installation method
- Requires installation by plumber*
- B type Installation Accessories If type A installation is inconvenient, please install type B.
Installation (This may differ from the product specification.)
-
A type Installation (Standard)
-
Close the water gauge.
-
Remove dust and sand in the water inlet when installing the shutoff valve.
-
Wind Teflon tape around the water pipe.
-
Connect the pipe with the shutoff valve.
-
Connect the Strainer Filter. B type Installation Accessories
Attach the provided water hose to your water shutoff valve. -
How to install the Ceramic
-
Connect Hose
-
Insert the brass part to the flushing outlet first.
-
Turn the nut clockwise to tighten the hose.
-
Connect Bidet to Toilet
-
Assemble the toilet with bidet, jet spray outlet and bowl washing outlet.
-
Insert the hose into the filter.
-
Insert bidet’s fixing hook onto the toilet’s fixing hook until it “clicks”.
-
Open the water valve Please plug in the power only after completing all installation and opening the water valve.
-
Connect Power
-
Insert the power plug into the outlet
-
Press the flush button – Water will fill the ceramic bowl.
The water may overflow out of the rim when cleaning the bowl in the region with high water pressure. Using a screwdriver, turn the shutoff valve clockwise to reduce the water pressure.