TRANSGO SKU140 U241E 1998-On Toyota Lexus Shift Kit Instruction Manual

TRANSGO SKU140 U241E 1998-On Toyota Lexus Shift Kit

Fits

Toyota U140 E &F 4 speeds:

• Camry 02-03 3.0L
• Matrix 09 2.4L
• Highlander 2.4 & 3.0L 01-03, 04-07 2.4L
• Rav-4 2.0 & 2.4L 00-08

Toyota U240 & U241 4 speeds:

• Celica GTS 1.8L U240E
• Highlander 2.4L 01-07 U241E
• Matrix 1.8L 03-06 U240E
• Rav4 2.0 & 2.4L 00-08 U241E
• Solara 2.4L 02-05 U241E

Lexus U140 E &F 4 speeds:

• ES300 99-01 3.0L
• RX300 98-03 3.0L

Heads UP!

Some U140’s develop a problem in the computer that gets worse the more it heats up. Symptoms include partial high gear start, bind-up in manual low, harsh shift or bind-up on the 2-3 shift. Check it like this: Using 2 digital volt-meters, watch the voltage on SL1+ and SL2+. In Drive, 1st gear, at a stop, should show 6.5 to 8 volts on both of the meters. On the 1-2 shift, SL1 will smoothly modulate down to 0 volts. On the 2-3 Shift, SL2 will smoothly modulate down to 0 Volts and SL1 may briefly modulate up but then drop to 0 again. Come to a stop SL1 & SL2 should return to 6.5 to 8 volts. If voltage drop is not smooth during 2-3 and / or voltage does not return to 6.5-8 Volts on SL2 when you come to a stop, suspect a bad computer. Dealer price is approx $700-900.00 but may be under an extended warranty. Check with Dealer.

Tech Notes:

Always mark the current locations of check balls, retainers etc. to insure they are returned to their original locations even if they differ from what is shown here. What is shown is a typical layout of this valve body. Use care in disassembling. Planetary Failure always REQUIRES a complete strip and cleaning of the valvebody!

INSTALLATION

Step 1

1. 1. Remove the “X” & “Z” bolts that hold the VB to the case. When reinstalling VB, install “Z” bolts first. They align the VB to the case. Disconnect wiring. The “F” Bolt holds filter to VB. Remove it & Filter as well.

2. Keep these bolts separate from the rest of the VB bolts.

SL1, SL2 & EPC 5-5.5 Ohms between pins S4 & DSL 11-15 Ohms between pins From Either Pin to Body of Solenoid must be open!

Separating Valve Body Halves

1. Step 1
   Flip the VB over so the accumulator side is facing up as shown at left. Remove the bolts marked with an “X”. Keep bolts from each side separated to make it easier to reinstall them later.

2. Step 2
   After removing the Accumulator body “X” bolts shown above, flip the VB over again and remove the “X” bolts shown at right. Finally, remove the 2 “A” bolts and lift the lower body AND the separator plate together as an assembly off the accumulator body. Flip Lower VB assembly over with separator plate facing up at you. Remove plate and mark the locations of any small parts on both VB halves such as check balls, filters, retainers etc. just in case they differ from what is shown in this instruction. Always reinstall them back in their original locations!

Accumulator Body Repair

1. Step 1 Remove and discard original Booster Bushing and Booster valve but SAVE the small inner spring! Clean & install original Lockup Valve, New Booster Bushing, original inner spring, New Booster Valve & retainer as shown.
2. Remove Solenoid Reg. Valve & Spring. The bore needs to be cleaned of any ridge that will cause the New Bushing to bind during installation. Prepare the bore for the New Bushing by taking the original valve and inserting it into the bore backwards. (Stem end outward.) Using the stem end as a handle, stroke the valve back and forth until any ridge or burr that you feel is gone. Don’t skip this step! IF BUSHING BINDS— STOP! Bore still has a ridge or burr!
   Preassembly Check– Clean new valve and bushing. Insert new valve into bushing and look for chips in drilled holes. Clean as necessary. We have gone to great lengths to remove them but occasionally one sneaks by.

Lube Upgrade Repair

1. Step 1
   Enlarge main separator plate holes A,B,C & D with .055 drill provided.
   Help This Trans Stay Cool! Do this step!

Typical Layout of Case Accumulators

Listen Up!
Shift feel and engagement concerns can be caused by accumulators that are not assembled correctly.

Typical O.E. VB shown for reference only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>