SECO SYS-D90-ITE MU1MWMO146 WiFi and BT module Installation Guide
- August 19, 2024
- SECO
Table of Contents
SYS-D90-ITE
INSTALLATION, USE AND
WARNINGS MANUAL
Edition: 07/2024
Preliminary information
1.1 Device description
The SYS-D90-ITE device is a new CONSOLE that included of HMI + Electronic
Board + Enclosure + OS, used to control and setup the weaving machine.
The technology developed by SECO S.p.A. can be used and applied in various
fields, such as:
1.2 Recipients
This manual is intended for ordinary people and installers (expert users).
IMPORTANT
The user must read this manual before start with any kind of operation.
1.3 Warranty
The warranty shall be voided in the event of:
- failure to comply with safety regulations;
- tampering with the device;
- changes to the safety conditions established by the Manufacturer in the device management software;
- improper use of the device;
- use of the device by untrained and/or unauthorized personnel or failure to respect duties, as indicated in the manual;
- changes or repairs carried out by the user without written authorization from the Manufacturer;
- partial or total failure to comply with the instructions;
- defects in the mains power supply (electricity, power supply, etc.);
- poor maintenance;
- use of non-original spare parts;
- exceptional events such as floods, fires (if not triggered by the device).
The complete warranty terms are set out in the sales contract.
IMPORTANT
The Manufacturer is not liable for improper use of the device.
Identification
2.1 Manufacturer identification
MANUFACTURER | SECO S.p.A |
---|---|
Address | Via Achille Grandi n°20 |
52100 Arezzo – Italy
Tel: +39 0575 26979
Fax: +39 0575 350210
2.2 Device identification
Device | SYS-D90-ITE |
---|---|
Serial number | YYMMXXXXX |
Year of manufacturing | 2023 |
2.3 Device identification plate
The device is equipped with an identification plate located on the side. The
plate features the device identification information to be reported to SECO
S.p.A. if necessary, as shown in the table:
SYS-D90-ITE-XX-C0 | ITE – Code that identifies the Client. |
---|---|
SYS-D90-ITE-XX-C0 | D90 – Code that identifies the electronic board inside the |
device.
CAUTION
It is strictly forbidden to remove the identification plate and/or replace it
with other plates.
Technical specifications
3.1 SYS-D90-ITE device hardware specifications
The table below features the board hardware specifications:
Processor| i.MX 8M Mini Quad – Full featured, 4x Cortex®-A53 cores up to
1.8GHz
---|---
Memory| 2GB LPDDR4
Mass Storage| 16GB eMMC
USB| 3x USB 2.0 TypeA
Serial Ports| RS-232 and CANBus on DB9 connectors
Other Interfaces| RTC
Power| 24VDC +/- 10%
Max 2,5 A
Linux Yocto
Runtime: Phyton support
SDK: QT creator with kit configured for sysroot
Boot: from eMMC or from external USB for recovery
Debug: Possibility of Debug over Serial or USB (MicroAB)
Desktop Environment: minimal for Filesystem accessibility
Server WEB: Lighttpd with HTML and css
Remote Access: ssh, ftp, mount remote file system
DBMS: Installed MySQL, PostgreeSQL, SQLite
System OS: Text Editor, PDF viewer, Browser WEB, image (jepg, bmp,
png) viewer and video, specifically pdfviewer = evince, browser =
Operating System| Chromium, video = VLC
Security: OpenSSL
International Characters/Font: Possibility to display any Unicode character
(Japanese, Chinese, Russian, Indian …) and Unicode font Filesystem: Any damage
to Filesystem in case of accidentally power off or power interruption will be
prevented, by using EXT4 with integrity check at boot time and mounting the
filesystem in read-only mode. When needed the file system will be temporary
remounted in write mode and the user will be prompted by SW application not to
switchoff the
system power. Partition for system in RO mode, data partition in RW mode.
Peripheral USB memory: automatic mount and unmount of USB memory. Unpredicted
disconnection of the USB memory or the peripheral, has not to create
instability or damage to the Filesystem console I/O User devices: Possibility
to connect USB keyboard and mouse System SW upgrade: Possibility to upgrade
system SW separately from the BSP (if allowed and compatible)
BSP upgrade: Possibility to upgrade the BSP (eg boot from USB) restoring the
user state of user filesystem (application, data, etc) (two partitions: one
for file system and the other for user space plus two hidden partition for
boot and recovery) Restore: possibility to restore the system to factory
state/condition from eMMC or USB in case of failure.
First installation of Application SW: Automatic or helped procedure, to drive
the first installation of the application SW (will be part of the development
of application SW) Autotest/SelfTest SW: Presence of Application/s act to
verify automatically the correct HW functionalities and troubleshooting
(touchscreen, display, I/O). Library to be present for multitouch support and
gesture.
VNC Server enable only if required. Or Remote access ssh, ftp.
Added library nxp-nfc for NFC USB devices
Storage Condition| 0°C to +50°C *
Transport Condition| – 25°C to +55°C **
Humidity| 95%
Type of installation| Industrial
ATTENTION
*The values indicated refer to the maximum temperature of the environment of use of the device. It is the customer’s responsibility to verify that the temperature remains within the admissible range indicated in this manual and, if necessary, adopt any passive cooling solution together with an application-dependent cooling system that can ensure that the heat sink temperature will not damage the device itself and/or the connected mechanical parts.
ATTENTION
** Incase the transport conditions may exceed the temperature and time range
indicated, corrective measures must be taken to avoid exposure of the device
and its possible damage.
3.2 Software Specifications
The software version released on the website
https://www.seco.com/it/products, which is always updated and available,
even in later versions.
3.3 CE reference directives
The device has been designed according to the following Directives:
- 2014/30/EU Electromagnetic Compatibility Directive.
- 2009/125/CE Ecodesign
- 2012/19/EU (WEEE)
- 2011/65/EU (RoHS)
- 2014/53/UE (RED), especially to the following standards:
- ETSI EN 301 489-1, ETSI EN 301 489-17, ETSI EN 300 328.
The device also meets the requirements of the following standards:
- EN 60204-1:2018.
3.4 Product Documentation
SECO S.p.A. places the device on the market, equipping and providing it with:
- CE marking as IT device
- Declaration of Conformity*
- User manual*
- FCC – Part 15 Certification**
*These documents are available after a request to the manufacturer.
3.5 FCC disclaimer
FCC references to product certification:
FCC ID: 2ALZB-7150PN, Contains FCC ID: 2ALZB-MU1MWMO146
This device complies with Part 15 of FCC Rules, Operation is Subject to
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference
that cause undesired operation.
** This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
No changes shall be made to the equipment without the manufacturer’s
permission as this may void the user’s authority to operate the equipment
3.6 Industry Canada (IC) Disclaimer
ISED references to product certification:
IC: 22688-7150PN, Contains IC: 22688-MU1MWMO146
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
IMPORTANT
The Manufacturer is not liable for improper use of the device.
Safety devices
4.1 Warnings
CAUTION
It is the user’s responsibility to apply preventive and protective measures,
in accordance with the legislation of the country of installation and use of
the device.
CAUTION
Only use the accessories supplied by the manufacturer.
CAUTION
Only connect certified peripherals / devices to the device.
CAUTION
Always disconnect the electrical power supply before carrying out any work on
the device.
CAUTION
Check that the electrical voltage meets the values indicated in this manual
before connecting the device.
CAUTION
Disconnect the device from any power source before cleaning.
CAUTION
Do not use liquid detergents or sprays for cleaning the device.
CAUTION
Do not pour liquids of any kind on the device. This may cause fires and/or
electric shocks.
CAUTION
Keep the device away from exposure to moisture values outside the admissible
range indicated in this manual.
CAUTION
To avoid the risk of electric shock, this equipment must only be connected to
a supply main with protective earth supply mains.
CAUTION
It is strictly forbidden to modify the appliance in order not to compromise
the characteristics relating to the declared requirements.
CAUTION
No changes shall be made to the equipment without the manufacturer’s
permission
as this may void the user’s authority to operate the equipment.
4.2 Safety pictograms affixed on the device and used in the manual
The device and the manual are equipped with symbols, as indicated in the table
below:
PICTOGRAM | DESCRIPTION |
---|---|
CE marking | |
RAEE |
Indicates the separate collection of electronic and electrical equipment
according to Directive 2012/19/EU.
| Symbol used to indicate the need to consult the instruction manual before
using the equipment.
Characteristics and components of the device
The SYS-D90-ITE device is a new CONSOLE that included of HMI + Electronic
Board + Enclosure + OS, used to control and setup the weaving machine.
The SYS-D90-ITE it is equipped with a cables connectors kit in order connect
properly to the destination machine.
5.1 Measurement layout
Length (A) | 400 mm |
---|---|
Width (B) | 250 mm |
Height | 67 mm |
5.2 Components
- must be used for installation/maintenance/update only.
Installation
6.1 Permitted environmental conditions
Use of the device and of associated control systems that differ from those
listed below is not permitted.
In particular, the installation and operation environment must not be:
- Exposed to environmental temperatures exceeding 0°C to +50°C.
- Exposed to limit areas of 2,000 m.a.s.l.
- Exposed to excessive humidity (minimum 5%, maximum 95 %) and rapid changes in relative humidity (above 0.005 p.u./h).
- Exposed to corrosive fumes.
- Exposed to excessive dust.
- Exposed to abrasive dust.
- Exposed to oil vapours.
- Exposed to powder or gas explosive mixtures.
- Exposed to salt air.
- Exposed to vibrations, impacts or abnormal shocks.
- Exposed to weather conditions beyond the limits permitted or dripping.
- Exposure to unusual transport or storage conditions.
- Exposure to high or rapid thermal changes (above 5K/h).
- Presence of nuclear radiation.
- The conductors of the command and control circuits directly connected to the supply voltage must be protected against overcurrents.
- The conductors of the command and control circuits fed by a transformer or by a DC supply must be protected against overcurrent.
- In command and control circuits connected to a protective equipotential circuit, the requirement is satisfied by inserting a protective device against overcurrents in the isolated conductor.
CAUTION
Environmental conditions that differ from those specified may seriously damage
the device. Positioning the device in environments that do not correspond to
those indicated shall render the warranty null and void for the parts to be
replaced.
SECO S.p.A. shall not be held liable if these instructions are not complied
with.
6.2 Installing the device
In order to install the device, make sure that the following cables connectors
are connected properly to the device:
| X1 = Vin (+24V and GND ) & CAN-bus
---|---
| X2 = RS-232 connector.
CAUTION
The power supply must have this values:
- Voltage: 24Vdc +/- 10%
- Current: 2.5 Amps Max
SECO S.p.A. shall not be held liable if these instructions are not complied with.
To install the device properly on the available support, follow the procedure below:
- Make sure the electric connection on the destination machine is off and the electric power supply is disconnected from the device;
- Fix the device to the existing support using 4 screws that will be screwed in matching the holes in the plate (A);
- Proceed to connect the electric supply to the device. Once inserted, turn the connector clockwise in order to lock it in place;
- Proceed to electrically connect the destination machine.
SECO S.p.A. shall not be held liable if these instructions are not complied with.
Maintenance
User should clean the product with a dry cloth when necessary, based on his
visual inspection.
CAUTION
Disconnect the device from any power source before cleaning operation.
WARNING
The enclosure of the device must be cleaned only with a dry cloth.
After cleaning, the user should check that the product is still correctly
installed.
Waste disposal
Electrical equipment no longer in use must not be thrown away with normal
municipal waste. The substances and materials it contains must be disposed of
separately in an appropriate manner.
The device must be disposed correctly as it is a waste of electric and
electronic equipment (WEEE).
Information subject to change. Please visit
www.seco.com to find the latest version of this manual.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>