HILTI HIT-ICE Adhesive Anchor User Guide
- June 1, 2024
- HILTI
Table of Contents
HILTI HIT-ICE Adhesive Anchor
Product Information
Specifications
- Product Name: Hilti HIT-ICE
- UFI: 6VVQ-V0D8-HX01-ACGC (A), WJ5R-003C-FX00-5UAV (B)
- Contains: dibenzoyl peroxide(B), hydroxypropylmethacrylate(A)
- Warnings: Heating may cause a fire. May cause allergic skin reaction. Causes serious eye irritation. Very toxic to aquatic life with long-lasting effects. Harmful to aquatic life with long-lasting effects.
Product Usage Instructions
-
Preparation
Ensure the surface is clean, dry, and free from any contaminants before using Hilti HIT-ICE. -
Mixing
Follow the recommended mixing ratios provided on the product packaging. Use appropriate tools to mix the components thoroughly. -
Application
Apply the mixed Hilti HIT-ICE to the desired area using a suitable application method. Ensure proper coverage and avoid over-application. -
Curing
Allow the product to cure for the specified time as indicated in the user manual. Avoid any disturbances during the curing process.
FAQ
-
Q: Can Hilti HIT-ICE be used underwater?
A: No, Hilti HIT-ICE is harmful to aquatic life and should not be used underwater. -
Q: What should I do if I experience skin irritation after using Hilti HIT-ICE?
A: Rinse the affected area with plenty of water and seek medical advice if irritation persists.
qr.hilti.com/manual/?id=2048491
WARNING
Contains: dibenzoyl peroxide(B), hydroxypropylmethacrylate(A)
Heating may cause a fire.(B) May cause an allergic skin reaction.(A,B) Causes
serious eye irritation.(A,B) Very toxic to aquatic life with long lasting
effects. (B) Harmful to aquatic life with long lasting effects.(A)
- UFI: 6VVQ-V0D8-HX01-ACGC (A)
- UFI: WJ5R-003C-FX00-5UAV (B)
Tools
- Dry concrete;
- Water saturated concrete;
- Hammer drilling;
- Hollow drill bit;
- Muster;
- Muster;
- Uncracked concrete;
- Cracked concrete;
- Groutfilled CMU;
- Working time;
- Curing time;
- Temperature of concrete;
- cartridge temperature
Hilti (Gt. Britain) Ltd. 1 Trafford Wharf Road Trafford Park GB-M17 1BY Manchester Tel +44 161 886 1000
Fractional/Imperial
d 0 [inch]| 1 US Rebar| 1 CA Rebar| 2
HIS-N, -RN| 3 HAS(-U) / HIT-V|
---|---|---|---|---|---
d| h ef [inch]| d| h ef [mm]| d
[inch]| h ef [inch]| d f [inch]| h s
[inch]| T inst [lb-ft]| d [inch]| h ef
[inch]| ****
h ef [inch]
| d f1 [inch]| d f2 [inch]| T inst
[Nm]| T inst [lb-ft]
7⁄16| | | | | | | | | | 3 ⁄ 8| 3 1⁄2| 2 3⁄8 …7 1⁄2| 1⁄2| 7⁄16| ≤
15| ≤ 20
1⁄2| #3| 2 3⁄8 …7 1⁄2| | | | | | | | | | | | | |
9⁄16| | | 10 M| 60…226| | | | | | 1 ⁄ 2| 4 1⁄4| 2 3⁄4
…10| 5⁄8| 9⁄16| ≤30| ≤40
5⁄8| #4| 2 3⁄8 …10| | | | | | | | | | | | | |
11⁄16| | | | | 3 ⁄ 8| 4 3⁄8| 7⁄16| 3⁄8 …15⁄16| ≤ 15| | | | | | |
3⁄4| #5| 3…12 1⁄2| 15 M| 80…320| | | | | | 5 ⁄ 8|
5| 3 1⁄8 …12 1⁄2| 13⁄16 | 11⁄16| ≤60| ≤80
7⁄8| #6| 3…15| | | 1 ⁄ 2| 5| 9⁄16| 1⁄2 …1 3⁄16| ≤ 30|
3 ⁄ 4| 6 5⁄8| 3 1⁄2 …15| 15⁄16| 13⁄16| ≤100| ≤136
1| #6| 3…15| 20 M| 90…390| | | | | | 7 ⁄ 8| | 3 1⁄2
…17 1⁄2| 1 1⁄8 | 15⁄16| ≤125| ≤169
#7| 3 1⁄3 …17 1⁄2
1 1⁄8| #7| 3 1⁄3 …17 1⁄2| | | 5 ⁄ 8| 6 3⁄4| 11⁄16| 5⁄8 …1
1⁄2| ≤ 60| 1| | 4…20| 1 1⁄4 | 1 1⁄8| ≤150| ≤203
#8| 4…20
1 1⁄4| #8| 4…20| 25 M| 101…504| 3 ⁄ 4| 8 1⁄8| 13⁄16|
3⁄4 …1 7⁄8| ≤ 100| | | | | | |
1 3⁄8| #9| 4 1⁄2 …22 5⁄9| 30 M| 120…598| | | | | | 1 1
⁄ 4| | 5…25| 1 1⁄2 *| 1 3⁄8| ≤200| ≤271
1 1⁄2| #10| 5…25| | | | | | | | | | | | | |
1 3⁄4| #11| 5 1⁄2 …27 1⁄2| | | | | | | | | | | | | |
Metric Values
d 0 [mm]| 1 EU Rebar| 2 HIS-N, -RN| 3
HAS(-U) / HIT-V|
---|---|---|---|---
d [mm]| h ef [mm]| d [mm]| h ef [mm]|
d f [mm]| h s [mm]| T inst [Nm]| d
[mm]| h ef [mm]| d f1 [mm]| d f2
[mm]| T inst [Nm]
10| 8| 60…160| | | | | | M8| 60…160| 11| 10| ≤10
12| 8| 60…160| | | | | | M10| 60…200| 14| 12| ≤20
10| 60…200
14| 10| 60…200| M8| 90| 9| 8…20| ≤10| M12| 70…240| 16| 14|
≤40
12| 70…240
16| 12| 70…240| | | | | | | | | |
18| 14| 75…280| M10| 110| 12| 10…25| ≤20| M16| 80…320| 20|
18| ≤80
20| 16| 80…320| | | | | | | | | |
22| | | M12| 125| 14| 12…30| ≤40| M20| 90…400| 24| 22| ≤150
25| 20| 90…400| | | | | | | | | |
28| | | M16| 170| 18| 16…40| ≤80| M24| 96…480| 30*| 28| ≤200
32| 25| 100…500| M20| 205| 22| 20…50| ≤150| | | | |
Hilti HIT-ICE
Contains: dibenzoyl peroxide(B), hydroxypropylmethacrylate(A) WARNING
- Heating may cause a fire.(B)
- May cause an allergic skin reaction.(A,B)
- Causes serious eye irritation.(A,B)
- Very toxic to aquatic life with long lasting effects. (B)
- Harmful to aquatic life with long lasting effects.(A)
- Keep away from heat/sparks/open flames/hot surfaces – No smoking.
- Do not get in eyes, on skin, or on clothing.
- Wear protective gloves/ protective clothing/eye protection.
- IF ON SKIN: Wash with plenty of soap and water.
- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- If skin irritation or rash occurs: Get medical advice/attention.
- If eye irritation persists: Get medical advice/attention.
Disposal considerations
- Empty packs: EAK waste material code: 150102 plastic packaging. | Full or partially emptied packs: Must be disposed of as special waste in accordance with official regulations. | EAK waste material code: 08 04 09 waste adhesives and sealants containing organic solvents or other dangerous substances. | or EAK waste material code: 20 01 27 paint, inks, adhesives and resins containing dangerous substances. | Content: 296 ml / 10.0 fl.oz. | Weight: 470 g / 16.6 oz
Hilti accepts no liability for damage or failure caused by: Storage and transport not in accordance with the specified conditions. | Failure to observe the instructions for use and setting data, incorrect use | Inadequate design of the anchor points, inadequate load bearing capacity of the base material | Other influences of which Hilti is not aware or on which Hilti has no influence, e.g. use with products from a third party.
Product Information
- Always keep these instructions together with the product even when given to other persons.
- Read the safety data sheet before use.
- Check expiration date (month/year) imprint on the label. Do not use expired product.
- Cartridge temperature during usage: -23 °C to 32 °C / -10 °F to 90 °F.
- Base material temperature at time of installation: between -23 °C to 32 °C / -10 °F to 90 °F.
- Conditions for transport and storage: Keep in a cool, dry and dark place between 5 °C and 25 °C / 41 °F and 77 °F.
- For any application not covered by this document / beyond values specified, please contact Hilti. | Partly used cartridges have to be used within 4 weeks. Leave the mixer attached and store under the recommended storage conditions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive, as described at paragraph 8.
NOTICE
-
Improper handling may cause mortar splashes. Always wear safety glasses, gloves and protective clothes during installation. | Never start dispensing without a mixer properly screwed on. | Attach a new mixer prior to dispensing a new cartridge (ensure snug fit). | Use only the type of mixer (HIT-M2) supplied with the adhesive. Do not modify the mixer in any way. | Never use damaged cartridges.
-
Poor load values / potential failure of fastening points due to inadequate borehole cleaning. Hilti hollow drill bits TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity
(volumetric flow rate) as specified in the accessory table. | The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection. | For blowing out the borehole – blow out with oil free air until return air stream is free of noticeable dust. For brushing the borehole – only use specified wire brush. The brush must resist insertion into the borehole – if not the brush is too small and must be replaced. -
Ensure that boreholes are filled from the back of the borehole without forming air voids. If necessary use the accessories / extensions to reach the back of the borehole. | For overhead applications use the overhead accessories HIT-SZ and take special care when inserting the fastening element. Excess adhesive may be forced out of the borehole. Make sure that no mortar drips onto the installer. | In water saturated concrete it is required to set the anchor immediately after cleaning the borehole.
-
Not adhering to these setting instructions can result in failure of fastening points!
Made in Germany
Hilti = registered trademark of
Hilti Corporation, Schaan, Liechtenstein
www.hilti.group
© 2024 Right of technical changes reserved S.E. & O
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>