WELLFOR EX-4024DHC LED Bathroom Mirror Installation Guide

WELLFOR EX-4024DHC LED Bathroom Mirror

Product Specifications

• Model: DHJSBM2432VCSKXXX, DHJSBM2836VCSKXXX, DHJSBM4024VCSKXXX
• Dimensions:
  • DHJSBM2432VCSKXXX: 24 inches width, 32 inches height
  • DHJSBM2836VCSKXXX: 28 inches width, 36 inches height
  • DHJSBM4024VCSKXXX: 40 inches width, 24 inches height
• Features:
  • Extra thick LED light
  • Touch switch with memory
  • Touch switch dimming function
  • Anti-fog pad

Installation Instructions

1. Read all instructions thoroughly before installing.
2. Check product list after opening the package.
3. Level and mark the location on the wall.
4. Place the mounting bar against the wall and make marks on the wall.
5. Drill holes and place suitable plastic anchors.
6. Screw the mounting bar onto the wall using screws.
7. Plug the power cord into the wall outlet (if applicable).
8. Connect the mirror wires to the main power using wire connectors:
   • BLACK WIRE — POWER SUPPLY L (LIVE)
   • WHITE WIRE — POWER SUPPLY N (NEUTRAL)
   • GREEN WIRE — POWER SUPPLY E (EARTH)
9. Hang the mirror onto the Z bar until securely in place.

Operation Instructions

• ON/OFF and Dimmer: Short-touch the button to turn on/off the mirror. Long touch to adjust brightness (dimming).
• Anti-fog Function: Press the defogger button to activate. Press again to deactivate.
• Night Light: 3000K Nightlight. Rocker switch controls auto-on/off based on surrounding brightness. Turn off manually if needed at night.

FAQ

• Q: How do I adjust the brightness of the LED light?
  A: Long touch the button to adjust the brightness levels.

• Q: How does the anti-fog function work?
  A: Press the defogger button to activate, and press again to deactivate the anti-fog function.

• Q: Can I turn off the nightlight manually?
  A: Yes, you can manually turn off the nightlight by switching off the rocker switch.

Product Features

• Extra thick LED light
• Touch switch with memory
• Touch switch dimming function
• Anti-fog pad

Installation and Operating Manual

For easy and safe installation, please refer to the following:
Read all instructions thoroughly before installing the enclosed product.
Read and take note of all safety, care and maintenance information.
PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE DURING PRODUCT OPERATION AND MAINTENANCE.

Important Tips

WARNING AND SAFETY INSTRUCTIONS
Before assembling your LED Lighted Mirror fixture, please make sure that you carefully read through this instruction sheet, refer back to them during installation to ensure your product is fitted safely and correctly. Keep these instructions for future use.
WARNING Risk of Fire and Electric Shock

• All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician.
• Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
• Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
• Regularly check the cord, the transformer and all other parts for damage, if any part is damaged the product should not be used.

INSTALLATION SAFETY

• Inspect the product immediately upon receipt for the transit damage or missing parts. Handle the product with care and protect against knocks to all sides and edges of the glass.
• Ensure there are no hidden pipes or cables in the wall before drilling.
• Wear suitable eye protection when drilling. Take care if drilling on tiled surfaces in case the drill slips.

CAUTION
The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Do not install this fixture in hazardous locations.

Accessories and Installation Steps

CHECK PRODUCT LIST AFTER OPENING THE PACKAGE

• LED Lighted Mirror — 1 pcs
• Screws for wall — 5 pcs
• Plastic Anchor –5 pcs
• Mounting bar –1 pcs
• Installation Manual — 1 pcs

TOOLS YOU MAY NEED

Installation Steps

1. Level and mark the location.

2. Place the mounting bar against the wall and make some marks on the wall.

3. Drill the holes and place the suitable plastic anchors.

4. Screw the mounting bar onto the wall with the screws .

5. • Plug the power cord onto the outlet on the wall.(Suit for the product with plug)
   • Connect the wires of mirror with the main power by the wire connectors.
     BLACK WIRE — POWER SUPPLY L (LIVE)
     WHITE WIRE — POWER SUPPLY N (NEUTRAL) GREEN WIRE — POWER SUPPLY E (EARTH)

6. Hang the mirror onto the Z bar until they are completely stuck.

Operation Instruction

ON/OFF and Dimmer

• Short-touch the button to turn on/off the mirror.
• Long touching the button to adjust the brightness.

Anti-fog Function

• Mirror begins to be warm and defog after pressing the defogger button.
• Press again to quit the anti-fog function.

Night light
(Suit for the product with night light function)

• Night light will be auto‐on/off according to the brightness surrounding when the rocker switch is keeping turned on.
• If need turn off the nightlight at night, please turn off the rocker switch manually.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>