Eversolo AMP-F2 Power Amplifier Instruction Manual

: August 14, 2024
: everSOLO

Table of Contents

Eversolo AMP-F2 Power Amplifier
Introduction
Specifications
Rear Panel Descriptions
Front Panel Descriptions
Controls
Set-up instructions
Downloads
Safety instructions
Limited warranty
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Eversolo AMP-F2 Power Amplifier

Introduction

Sincerity and efficiency
For true audiophile performance. Work with the united strength of Starke Sound’s team and Eversolo’s team, based on the Starke Sound NS600 amp module, raising its sampling rate to 600 kHz and further reducing noise with a newly designed SAPS switch mode power supply of 600 watts. Implementing the high efficiency of class D with all circuits supporting maximum sound quality, AMP-F2 also offers the flexibility of 2-channel or bridged mono-channel operation.

With the same width and height, and optimized signal path, AMP-F2 is a perfect match with DMP-A6, an ideal combination of value and performance. It is advised to read this manual to make sure the product’s features are applied correctly.

Specifications

Rear Panel Descriptions

Descriptions:

Power on /off
Power input plug
(Warning: Please carefully check the input power voltage setting before inserting the power supply, adjust to the position suitable for the local voltage, and replace the corresponding fuse with proper specifications, the power amplifier could burn with an incorrect fuse! Use a 3.15A fuse at 220V- 240V, or a 6.3A fuse at 110V-120V)
Voltage switching
Output(Used to connect the loudspeaker terminals)
XLR / RCA Analog input
XLR Input / RCA Input switch
BRIDGE switch(AMP-F2 is bridgeable. STD is standard mode, and BRIDGE is bridge mode. In bridge mode, only the input and output with the diagonal line area are working.)
Trigger output (can be linked to another trigger gear)
Trigger input (can be linked to the previous stage with trigger function)

Front Panel Descriptions

Controls

Short press:
Power on/Power off/Reboot/
Indicator light:
- In standby mode, the indicator light is orange.
- In the working state, the indicator light is white.

Set-up instructions

For standard mode, set this switch to STD (standard). For bridge mode, set this switch to BRIDGE.

Connect your 2 input channels using either unbalanced (RCA) or balanced (XLR) cables. Channels are labeled 1 and 2. Set the two toggle switches to UNBAL (unbalanced) or BAL (balanced) as appropriate.

Connect your two speakers to the output binding posts: 1 and 2. Speaker wires can be terminated with “banana plugs” which are inserted, or stripped insulation (unscrew the binding post cap,
insert the wire into the hole on the threaded shaft, and tighten the cap). Observe correct polarity ( “+” red and “-” black).

Connect your power cord to the wall outlet. Please note that the voltage is consistent with the local area. Then put the switch to the ON position and turn on the power of the amplifier.
AMP-F2 can be turned on/standby through the front panel power on/off button, it can also be turned on/standby automatically by the trigger cable.
When the TRIGGER IN jack is connected to a device equipped with a TRIGGER OUT jack, the power on/standby of the unit can be controlled through the linkage operation of the upstream connected device.
When the TRIGGER OUT jack is connected to a device equipped with a TRIGGER IN jack, the power on/standby of the downstream connected device can be controlled through the linked operation of this unit.
TRIGGER IN/OUT jack Inputs/outputs electrical signals are up to 12V DC/150mA.
In TRIGGER mode, the front panel power on/off button will be disabled and the on/off will be controlled by Trigger.

Downloads

For more tutorials, please visit www.eversolo.com, please visit the Downloads page on the official website, and scan the QR code.

Wechat Subscription

Safety instructions

Read, follow, and keep these instructions
Do not remove the cover as repairs require qualified technicians
Do not use the product near water
Do not install near any heat sources such as radiators, heaters, stoves, or amplifiers
Clean the product only with a damp cloth
Use care when lifting or moving this heavy product
Protect the power cord from being walked on or pinched
Unplug during lightning storms or when unused for long periods of time
Ensure that no objects filled with liquids such as vases are placed on the product

Limited warranty

1 year from purchase date (Save the original invoice for service to be arranged through your dealer, or contact us directly if you purchased your amplifier online.)

Starke Sound Inc.