4K-PTZ430HSU3N 4K UHD PTZ Camera

Product Information

Specifications

• Product Name: Prestel 4K-PTZ430HSU3N
• Resolution: 4K UHD
• Camera Type: PTZ (Pan-Tilt-Zoom)
• Compliance: FCC Class A, European Community Class A

Product Usage Instructions

6. GUI Settings

Refer to section 6 in the user manual for detailed instructions
on GUI settings.

7. WEB Settings

Access the camera settings through the web interface by
following the steps outlined in section 7 of the user manual.

7.1 Access Camera

Learn how to access the camera settings on the web interface in
section 7.1.

7.2 Control Camera

Discover how to control the camera functions through the web
interface in section 7.2.

FAQ

Q: Can I use this camera for live streaming?

A: Yes, this camera supports live streaming. You can configure
the settings for streaming in the web interface under Video
Settings.

Q: How do I adjust the exposure settings of the camera?

A: To adjust exposure settings, navigate to Image Settings in
the web interface and select Exposure. From there, you can modify
the exposure levels according to your preferences.

Prestel 4K-PTZ430HSU3N
4K UHD PTZ Camera
USER MANUAL

Copyright
All contents of this manual, whose copyright belongs to ourcorporation, cannot be cloned, copied or translated without the permission of our corporation.
Notice
Product specifications and information which were referred to in this document are for reference only. We may change, delete, or update any content at any time and without prior notice.
FCC NOTICE (Class A)
This product complies with Part 15 of the FCC Rules. The operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/television technician for help.
Class A ITE
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning
Operating this equipment in a residential environment may cause radio interference.
European Community Compliance Statement (Class A)
This product is herewith confirmed to comply with the requirements set out in the Council Directives on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive

4K UHD PTZ Camera

User Manual

Catalogue
1 Safety Precautions……………………………………………………………………………. 1 2 Packing List ……………………………………………………………………………………… 1 3 Product Connection ………………………………………………………………………….. 1 4 Video Format…………………………………………………………………………………….3 5 About Product …………………………………………………………………………………..3
5.1 Features …………………………………………………………………………………………………. 3 5.2 Specifications …………………………………………………………………………………………. 5 5.3 Interface and Switch ………………………………………………………………………………… 7 5.4 Dimension ………………………………………………………………………………………………. 7 5.5 Installation ……………………………………………………………………………………………… 8 5.6 Remote Control ……………………………………………………………………………………….. 9
6 GUI Settings …………………………………………………………………………………….11
6.1 MENU…………………………………………………………………………………………………….. 11 6.2 EXPOSURE………………………………………………………………………………………………11 6.3 COLOR………………………………………………………………………………………………….. 12 6.4 IMAGE ………………………………………………………………………………………………….. 13 6.5 P/T/Z ……………………………………………………………………………………………………. 13 6.6 NOISE REDUCTION………………………………………………………………………………….. 13 6.7 SETUP ………………………………………………………………………………………………….. 13 6.8 TRACKING CONFIG …………………………………………………………………………………. 14 6.9 COMMUNICATION SETUP ………………………………………………………………………… 14 6.10 RESTORE DEFAULT…………………………………………………………………………………. 15
7 WEB Settings …………………………………………………………………………………. 15
7.1 Access Camera ……………………………………………………………………………………… 15 7.2 Control Camera ……………………………………………………………………………………… 15 7.3 Video Settings……………………………………………………………………………………….. 17 7.4 Tracking Settings …………………………………………………………………………………… 18
7.4.1 Presenter …………………………………………………………………………………………………. 18
7.4.2 Zone ………………………………………………………………………………………………………… 18
7.5 Image Settings ………………………………………………………………………………………. 19 7.5.1 Exposure ………………………………………………………………………………………………….. 19
7.5.2 Color……………………………………………………………………………………………………….. 20
7.5.3 Image ……………………………………………………………………………………………………… 20
7.5.4 PTZ …………………………………………………………………………………………………………. 20

4K UHD PTZ Camera

User Manual

7.5.5 Noise ……………………………………………………………………………………………………….. 21 7.6 Audio Settings……………………………………………………………………………………….. 21 7.7 System Settings …………………………………………………………………………………….. 21
7.7.1 Initialize …………………………………………………………………………………………………… 21 7.7.2 User …………………………………………………………………………………………………………. 21 7.7.3 U Disk Record ……………………………………………………………………………………………. 21 7.7.4 Online Upgrade ………………………………………………………………………………………….22 7.8 Network Settings……………………………………………………………………………………. 22 7.8.1 Lan……………………………………………………………………………………………………………22 7.8.2 Port…………………………………………………………………………………………………………..22 7.8.3 RTMP(S) ……………………………………………………………………………………………………22 7.8.4 SRT Settings ……………………………………………………………………………………………. 23 7.8.5 RTSP……………………………………………………………………………………………………….. 23 7.8.6 ONVIF ……………………………………………………………………………………………………… 23 7.8.7 Multicast …………………………………………………………………………………………………. 23 7.8.8 FreeD ………………………………………………………………………………………………………. 24 7.8.9 NTP…………………………………………………………………………………………………………. 24 7.9 Overlay………………………………………………………………………………………………….24 7.10 Device Information…………………………………………………………………………………..24
8 AI Tracking ……………………………………………………………………………………..24
8.1 Web Control …………………………………………………………………………………………..24 8.2 Remote Control ………………………………………………………………………………………36
9 Troubleshooting ……………………………………………………………………………..38

4K UHD PTZ Camera

User Manual

1 Safety Precautions
During the installation and use of the equipment, all electrical safety regulations of the country and region of use must be strictly observed.
Please use the power adapter that comes standard with this product.
Please do not connect multiple devices to the same power adapter (exceeding the capacity of the adapter may generate excessive heat or cause a fire).
Do not rotate head of the camera by hand, otherwise it may cause mechanical failure.
When installing this product on a wall or ceiling, secure the device securely. When installing, make sure that there are no obstacles within the rotation range of the gimbal; do not turn on the power until all installations are completed.
To avoid heat build-up, keep ventilation around the device smooth.

If the device emits smoke, smells, or makes noises, please turn off the power immediately and unplug the power cord, and contact the dealer in time.
This device is not waterproof, please keep the device dry.
This product has no user serviceable parts, damage caused by disassembly by the user is not covered by the warranty.

Notice
Specific frequencies of electromagnetic field may affect the image of the camera!

2 Packing List

Name Camera Remote Control Power Adapter Power Cable RS232 Cable USBCable (Optional) User Manual

Quantity 1 1 1 1 1 1 1

3 Product Connection

1. Please check connections are correct before starting.

1

4K UHD PTZ Camera

User Manual

LINEIN LINEOUT

SYSTEM SELECT RS485

IN RS232 OUT

DC 12V

LAN

USB2.0 USB3.0

3G-SDI

HDMI RESTORE

The schematic diagram is for reference only. Please refer to the actual Note application scenario for product connection.

4K UHD PTZ Camera

User Manual

2. After the camera is powered on, it starts to initialize, right up to the limit position, and then both horizontal and vertical go to the middle position, the motor stops running, and the initialization is completed. (Note: If preset 0 is saved, PTZ will be move to preset 0)

4 Video Format

HDMI

SDI

0

1080P60

0

1080P60

1

1080P50

1

1080P50

2

1080I60

2

1080I60

3

1080I50

3

1080I50

4

1080P30

4

1080P30

5

720P60

5

720P60

6

1080P29.9 7

6

1080P29.9 7

7 1080I59.94 7 1080I59.94

8

1080P59.9 4

8

1080P59.9 4

9 720P59.94 9 720P59.94

A

4KP29.97

A

1080P29.9 7

B

4KP59.94

B

1080P59.9 4

C

4KP25

C

1080P25

D

4KP30

D

1080P30

E

4KP50

E

1080P50

F

4KP60

F

1080P60

such as education, conferences and live broadcasts.

Notice
After switching the video format, you need to restart the camera before taking effect!
5 About Product
5.1 Features AI Tracking With the help of the AI computing power of the chip, the camera is equipped with advanced AI algorithms to realize monocular humanoid tracking, which can realize automatic tracking of scenes
3

4K UHD PTZ Camera

User Manual

NDI|HX2(Optional) NDI|HX2 has the characteristics of low delay and plug and play, which is convenient for project implementation and deployment. It has good ecology and supports the simultaneous transmission of audio, video and control commands. It is a new generation of network video transmission mode. 4K UHD Usenew 1/1.8-inch high-quality UHD CMOS sensor with a maximum of 8.42 million pixels can realize 4K (3840×2160) ultra-high-resolution high-quality images. And downward compatible with 1080P, 720P and other resolutions. 30x Optical Zoom It adopts 4K ultra long focal lens with high quality and 8 million ultra-high resolution, 30x optical zoom, and the maximum field angle is 59°. HDMI2. 0 Support HDMI 2.0 interface, which can directly output 4KP60 uncompressed digital video. LowLight The application of 3D noise reduction algorithm greatly reduces image noise. Even under the condition of ultra-low illumination, it still keep the picture clean and clear, and the SNR of image is as high as 55dB. Multiple Interfaces Support HDMI and 3G-SDI interface, effective transmission distance of 3G-SDI is up to 150 meters (1080P30). HDMI or 3G-SDI, USB, LAN can output three HD digital signals at the same time. Remote Control Through the RS232 and RS485 serial ports, the camera can be controlled remotely. Gravity Sensor It supports automatic image flipping

function, which is convenient for engineering installation and use.

4

4K UHD PTZ Camera

User Manual

5.2 Specifications

Camera
Signal System
Sensor Scanning Mode Lens Digital Zoom Minimum Illumination Shutter White Balance Backlight Compensatio n Digital Noise Reduction SNR Horizontal FOV Vertical FOV Pan Angle Tilt Angle Pan Speed Tilt Speed Image Flip Image Freeze

HDMI: 4KP60, 4KP50, 4KP30, 4KP25, 4KP59.94, 4KP29.97, 1080P60, 1080P50, 1080P59.94, 1080P30, 1080P29.97, 1080I60, 1080I50, 1080I59.94, 720P60, 720P59.94 3G-SDI: 1080P60, 1080P50, 1080P30,1080P29.97, 1080P59.94, 1080P25, 1080I60, 1080I50, 1080I59.94, 720P60, 720P59.94 1/1.8 inch, CMOS, Effective pixels: 8.42M
Progressive
30x,f=7.1mm~210mm,F 1.61~F5.19 16x 0.5 Lux @ (F1.8, AGC ON) 1/30s~1/10000s Auto, Indoor, Outdoor, One Push, Manual, VAR
Support
3D Digital Noise Reduction
55dB
59.2°~2.5°
34.6°~1.4°
±170°
-30°~+90°
1.7°/s ~100°/s
1.7°/s~69.9°/s
Support
Support

PoE+

Support

Preset Position Preset Accuracy

255 0.1°

USB Features(USB 3.0 Optional)

Operate System Color System/ Compression
USB3.0 Video Format(Optio nal)
USB2.0 Video Format

Windows 7/8/10, Mac OS X, Linux, Android

YUY2/H.264/H.265/MJ PEG

YUY2:

1080P30

(max.)

H.264 AVC: 4KP30

(max.)

H.265 HEVC: 4KP30

(max.)

MJPEG:

4KP30

(max.)

YUY2:

1080P5

(max.)

H.264 AVC: 4KP30

(max.)

H.265 HEVC: 4KP30

(max.)

MJPEG:

4KP30

(max.)

USB Audio

Support

USB Video Protocol

UVC 1.1~UVC 1.5

UVC PTZ

Support

Network Features

Video Compression Video Stream
First Stream Resolution
Second Stream Resolution
Video Bit Rate
Bit Rate Control

H.264/H.265/MJPEG
First Stream, Second Stream 3840×2160, 1920×1080, 1280×720, 1024×576, 720×480, 720×408, 640×480, 640×360 720×480, 720×408, 640×480, 640×360, 480×320, 320×240 First Stream:
32kbps~51200kbps Second Stream:
32kbps~20480kbps
CBR, VBR

Frame Rate
5

50Hz: 1fps~50fps 60Hz: 1fps~60fps

4K UHD PTZ Camera

User Manual

Audio Compression Audio Bit Rate
Protocols

AAC
96K, 128K
NDI®|HX2, TCP/IP, HTTP, RTSP, RTMP(S), ONVIF, DHCP, SRT, Multicast, etc.

Interfaces

Audio Interface
Communicati on Interface
Network Interface

1 x LINE IN: 3.5mm Audio Input Interface
1 x LINE OUT: 3.5mm Audio Output Interface
1 x RS485: 2pin phoenix port, Max Distance: 1200m, Protocol: VISCA/Pelco-D/ Pelco-P
1xRS232 IN: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA/Pelco-D/Pelco-P
1 x RS232 OUT: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA network use only
1xLAN: 10M/100M/1000M Adaptive Ethernet Port

USBInterface
VideoInterfac e

1xUSB2.0: Type-A
1xUSB3.0: Type-B(Optional) 1x3G-SDI: BNC type, 800mVp-p, 75. Along to SMPTE 424M standard

1 x HDMI: Version 2.0

Power Interface

JEITA type (DC 12V)

General Specifications

Input Voltage DC 12V/PoE+

Input Current
Operating Temperature Storage Temperature Power Consumption

2A (max.) 0°C~40°C -40°C~60°C 18W (max.)

Dimension Net Weight

169mm x 188mm x 226mm
About 2.3Kg

NoteProduct specifications and parameters are subject to change without notice.

6

4K UHD PTZ Camera

User Manual

5.3 Interface and Switch

12

34 5 6

7

LINEIN LINEOUT

SYSTEM SELECT RS485

IN RS232 OUT

DC12V LAN

USB2.0 USB3.0

3G-SDI

HDMI RESTORE

8 9 10 11 12 13 14

No.

Name

1

LINE IN Interface

2

LINE OUTInterface

3

SYSTEM SELECT Switch

4

RS485 Interface

5

RS232 IN Interface

6

RS232 OUT Interface

7

Security Slot

8

DC 12V Interface

9

LAN Interface

10

USB2.0 Interface

11

USB3.0 Interface

12

3G-SDI Interface

13

HDMI Interface

14

RESTOREKey

5.4 Dimension

Unit: mm

53.7 176.8 226

STANDBY

POWER

169

7

14

4K UHD PTZ Camera

User Manual
1/4”-20UNC

Ø 100

188
5.5 Installation
1

90° 4-M3

2

Wall Mount

1

2

Ceiling Mount

The above installation diagram is for reference only, please refer to actual Note product for the installation accessories.
8

4K UHD PTZ Camera

User Manual

5.6 Remote Control

1

CAMERA SELECT

1

2

3

4

10

STD

REV

2

123

456

789

3

0#

11

F1 F2 F3 F4

12

OFF

AUTOTRACKING

PRESET

RESET

4

13

5

14

6

15

MENU

SLOW ZOOM FAST

7

16

/

BACKLIGHT /

8

17

9 FOCUS

Key Description
1. (Standby) Key Press to enter standby mode 2. Number Keys To set preset or call preset 3. * Key Use with other keys 4. PRESET Key Set preset: Successively press [PRESET] + Number key (0-9) 5. HOME Key Confirm selection or press to turn PTZ back to the middle position 6. (Return) Key Press to return to the previous menu

9

7. ZOOM Keys SLOW: Zoom In [+] or Zoom Out [-] slowly FAST: Zoom In [+] or Zoom Out [-] fast
8. L/R SET Key Standard: Simultaneously press [L/R
SET] + [1] Reverse: Simultaneously press [L/R
SET] + [2] 9. FOCUS Keys
Auto/Manual/Far-end/Near-end focus
10. CAMERA SELECT Keys
Press to select and control the camera
11. # Key
Use with other keys
12. Auto Tracking Keys
[F1]: Disable[F2]: Disable [F3]: Enable AI Tracking [F4]: Disable AI Tracking
13. RESET Key
Clear preset position: Successively press [RESET] + Number key (0-9)
14. PTZ Control Keys
PTZ moved according to the arrow indicates
15. MENU Key
Enter OSD menu or back to the previous menu
16. BACKLIGHT Key
Backlight ON/OFF: Press repeatedly to enable or disable the backlight compensation Effective only in auto exposure mode If there is a light behind the subject,
the subject will become dark, press the backlight key to enable the backlight compensation. Press again to disable this function.
17. P/T RST (PTZ Reset) Key
Press to preset Pan/Tilt self-test
Shortcut Set
Successively press [#] + [] + [F4]: Enable or disable the Image Freeze Successively press [] + [#] + [1]: OSD menu default English Successively press [] + [#] + [3]: OSD menu default Chinese Successively press [] + [#] +

recover the default Successively press [*] + [#] + [8]: Check the camera version

4K UHD PTZ Camera

User Manual

Successively press [] + [#] + [9]: Quickly set up inversion Successively press [] + [#] + [MANUAL]: Restore to default IP address

10

4K UHD PTZ Camera

User Manual

6 GUI Settings
6.1 MENU
Press [MENU] key to display the main menu on the normal screen, using arrow key to move the cursor to the item to be set. Press the [HOME] key to enter the corresponding sub-menu.
MENU Exposure Color Image P/T/Z Noise Reduction Setup Tracking Config Communication Setup Restore Default

Backlight:On, Off (Effective only in Automode). Bright: 0~17 (Effective only in Bright mode).

[HOME] Enter [MENU] Exit

6.2 EXPOSURE Move the main menu cursor to [Exposure], and press [HOME] key enter the exposure page, as shown in the following figure.

EXPOSURE
Mode ExpCompMode Backlight Gain Limit Anti-Flicker Meter DRC

Auto Off Off 10 50Hz Average 1

Select Item Change Value [MENU] Back
Mode:Auto,Manual, SAE, AAE, Bright. ExpCompMode:On, Off (Effective only inAutomode). ExpComp:-7~7 (Effective only in ExpCompMode item to On).
11

4K UHD PTZ Camera

User Manual

Gain Limit:0~15 (Effective only in Auto, SAE, AAE, Bright mode). Anti- Flicker:Off, 50Hz, 60Hz (Effective only in Auto, AAE, Bright mode). Meter: Average, Center, Smart, Top (Effective only in Auto, SAE, AAE, Bright mode). Iris:F1.8, F2.0, F2.4, F2.8, F3.4, F4.0, F4.8, F5.6, F6.8, F8.0, F9.6, F11.0, Close (Effective only in Manual, AAE mode). Shutter:1/30,1/60,1/90,1/100,1/125,1/18 0,1/250,1/350,1/500,1/725,1/1000,1/15 00,1/2000,1/3000,1/4000,1/6000,1/10 000 (Effective only in Manual, SAE mode). Gain:0~7 (Effective only in Manual mode). DRC:0~8.

6.3 COLOR Move the main menu cursor to [Color], and press [HOME] key enter the color page, as shown in the following figure.

COLOR
WB Mode RG Tuning BG Tuning Saturation Hue

Auto 0 0 100% 7

Select Item Change Value [MENU] Back
WBMode:Auto, Indoor, Outdoor, One Push, Manual, VAR. RG: 0~255 (Effective only in Manual mode). BG: 0~255 (Effective only in Manual mode). RG Tuning: -10~+10 (Effective only in Auto, One Push, VAR mode). BG Tuning: -10~+10 (Effective only in Auto, One Push, VAR mode). Saturation: 60%~200%. Hue:0~14.

Color Temp: 2500K~8000K (Effective only in VAR mode).

12

4K UHD PTZ Camera

User Manual

6.4 IMAGE Move the main menu cursor to [Image], and press [HOME] key enter the image page, as shown in the following figure.

IMAGE
Luminance Contrast Sharpness Flip-H Flip-V B&W-Mode Gamma Style

7 7 6 Off Off Off Default Default

Select Item Change Value [MENU] Back

Luminance: 0~14. Contrast: 0~14. Sharpness:0~11. Flip-H: On, Off. Flip-V: On, Off. B&W-Mode:On, Off. Gamma: Default, 0.45, 0.48, 0.5, 0.56, PC. Style: Default, Norm, Bright, PC.

6.5 P/T/Z Move the main menu cursor to [P/T/Z], and press [HOME] key enter the P/T/Z page, as shown in the following figure.

P/T/Z
SpeedByZoom AF-Zone AF-Sense L/R Set Display Info Image Freeze Digital Zoom Call Preset Speed Pre Zoom Speed

On Front High STD On Off Off 24 5

Select Item Change Value [MENU] Back
SpeedByZoom:On, Off. AF-Zone:Front, Top, Center, Bottom.

AF-Sense:High, Low, Normal. L/R Set: STD, REV. Display Info:On, Off. Image Freeze:On, Off. Digital Zoom:Off, 2x, 4x, 8x, 16x. Call Preset Speed: 1~24. Pre Zoom Speed:0~7.
6.6 NOISE REDUCTION Move the main menu cursor to [Noise Reduction], and press [HOME] key enter the noise reduction page, as shown in the following figure.
NOISE REDUCTION NR3D-Level 6

Select Item Change Value [MENU] Back

NR3D Level:Off, 1~9.

6.7 SETUP Move the main menu cursor to [Setup], and press [HOME] key enter the setup page, as shown in the following figure.

SETUP
Language DVI Mode Auto Patrol Video Mode Other

EN HDMI Off

Select Item Change Value [MENU] Back
Language: EN, Chinese, Russian. DVI Mode: HDMI, DVI. Auto Patrol:On, Off. Residence Time: 1~60(Effective only in Auto Patrol item to On). Call Preset Speed: 1~24(Effective only in Auto Patrol item to On).

13

4K UHD PTZ Camera

User Manual

Video Mode:Press the [HOME] key to confirm enter the “Video Mode” page and set SDI-3G Mode, Video Output. SDI-3G Mode: LEVEL-A, LEVEL-B. Video Output: HDMI, SDI. Other:Press the [HOME] key to confirm enter the “Other” page and set Auto Inversion, Tally Mode, and Preset Parameters. Auto Inversion: On, Off. Tally Mode: On, Off. Preset Parameters: On, Off.

6.8 TRACKING CONFIG Move the main menu cursor to [Tracking Config], and press [HOME] key enter the tracking config page, as shown in the following figure.

TRACKING CONFIG

Tracking

On

Tracking Mode Region

Figure Size

Close

Protocol:Auto, VISCA, PELCO-D, PELCO-P.

Select Item Change Value [MENU] Back

Tracking:On, Off. Tracking Mode:Region, Presenter. Figure Size: Full, Upper, Close, Custom.

6.9 COMMUNICATION SETUP Move the main menu cursor to [Communication Setup], and press [HOME] key enter the communication setup page, as shown in the following figure.

COMMUNICATION SETUP

Protocol

VISCA

V_Address 1

V_AddrFix

Off

Net Mode

Serial

Baudrate

9600

Select Item Change Value [MENU] Back
14

4K UHD PTZ Camera

User Manual

V_Address:1~7(Effective only in Auto, VISCAprotocol). V_AddrFix:On, Off (When set to On, useless in 88 30 01 FF Command). P_D_Address: 0~254(Effective only in Auto,PELCO-D protocol). P_P_Address: 0~31(Effective only in Auto,PELCO-P protocol). Net Mode: Serial, Paral(Effective only in Auto, VISCAprotocol). Baudrate: 2400, 4800, 9600, 38400.

6.10 RESTORE DEFAULT Move the main menu cursor to [Restore Default], press [HOME] key enter restore default page, as shown in the following figure.

RESTORE DEFAULT

Restore?

No

Change Value [HOME] OK [MENU] Back
Restore:Yes, No.

7.2 Control Camera All pages include two menu bars: Real Time Monitoring: Video image displaying with function buttons. Parameter Setup: Parameter configurating. A. Video Viewing Window
The video viewing window is same as video resolution, the bigger the resolution, the bigger the playing area. Double click the viewing window to show full screen, double click again, to return to initialized size. Status bar in viewing window shown as below:
4:18
Full screen switch button. B. PTZ Setup

Note
GUI menu and device information are subject to change without notice.

7 WEB Settings
7.1 Access Camera Access http://192.168.100.88 to pop up the login window, then input username (default: admin) and password (default: admin). After login, it will show as below:
Live Video Tracking Image Audio System Network Overlay Information

Zoom In

Zoom Out

Focus In

Focus Out

Pan Speed

10

Tilt Speed

10

15

4K UHD PTZ Camera

User Manual

1. Pan and Tilt Control The direction arrows and HOME button allow you to manually drive the camera to desired position. 2) Zoom Zoom In and Zoom Out buttons allow for wide or narrow view of the space. 3) Focus Focus In and Focus Out button allow for fine manual focus adjustment if the camera has any auto focusing problems on difficult object. 4) PTZ Speeds Pan speed rate can be set to 1~24, Tilt speed rate can be set to 1~20. Zoom and Focus speed rate can be set to 1~7. 5) Focus Mode Focus Mode can be selected Auto/Manual. When you select “Manual”, Focus In and Focus Out will to take effect. 6) PTZ Presets When the PTZ turns to the position that you would like to return to later, you can set presets for quick recall. Type a number (0~254) into the preset box and click “Set” button to save. When the PTZ turn to other position, input the preset number and click “Call” button to turn the PTZ back to the preset position. 7) PTZ/OSD Move the cursor to dropdown menu, select and click “OSD” to open the on-screen menu and do menu settings on the interface. 8) Tracking Turn On/Off the Track function and Tracking hint. Set Mode (Zone, Presenter) and Humanoid box.
   C. Language Selection

16

4K UHD PTZ Camera

User Manual

English ()
Language
Click either “Chinese”, “English” or “Russian” to change the language of the webpage.

7.3 Video Settings

Video Settings

HDMI/SDI Output Video Format Encode Level
First Stream

HDMI Dial Priority mainprofile

Encode Protocol H264

Resolution 1920×1080

Bit Rate 4096

Frame Rate 30

fps

I Key Frame Interval 30

Bit Rate Control CBR

Second Stream

Encode Protocol H264

Resolution 640×360

Bit Rate 2048

Frame Rate 30

fps

I Key Frame Interval 30

Bit Rate Control CBR

Submit

Cancel

1. HDMI/SDI Output Support HDMI and SDI Output. 2) Video Format Support 50Hz, 60Hz and Dial Priority. 3) Encode Level Support mainprofile and highprofiletwo levels. 4) Encode Protocol Support H264, H265and MJPEG protocols. 5) Resolution First stream support 3840×2160, 1920×1080, 1280×720, 1024×576, 720×480, 720×408, 640×480, 640×360.Second stream support720x480, 720×408, 640×480, 640×360, 480×320, 320×240; The bigger resolution is, the clearer the image will be, more network bandwidth will be taken.

17

4K UHD PTZ Camera

User Manual

6. Bit Rate The user can specify the bit rate. Generally speaking, the larger of the bit rate, the clearer of the image. However, the configuration of the bit rate needs to be combined with the network bandwidth. When the network bandwidth is narrow and the bit rate is configuredlarger, the video stream cannot be transmitted normally, and the visual effect is worse. 7) Frame Rate User can specify the size of the frame rate, generally, the frame rategreater, the image more smooth; Frame rate is smaller, the more sense of beating. 8) I Key Frame Interval Set interval between 2 I frame,the bigger interval isthe response will be lower from view window. 9) Bit Rate Control Code stream control way: CBR (Constant Bit Rate): Video coder will be coding according to preset speed. VBR(Variable Bit Rate): Video coder will adjust the speed based on preset speed to gain the best image quality.
   7.4 Tracking Settings
   7.4.1 Presenter

7. Auto Zoom/Auto Tilt

When Auto Zoom or Tilt is off, camera

stops

zooming in/out or tilting automatically.

Determine the zoom size and tilt position

based on the tracking start position you

choose.When auto zoom is off, camera

stops

zooming

In/Out

automatically.When auto tilt is off,

camera only move horizontally.

2. Target Retention Time

Set Target Retention Time, the time to

return to the starting point after losing

the target.

3. Figure Size

Figure Size:Full, Upper, Close, Custom.

4. Tracking Start Position

Tracking Start Position:Current Location,

Preset 1.

5. Character Position

Character Position:Left, Middle, Right.

7.4.2 Zone

Presenter

Zone

A

B

C

D

Presenter

Zone

Auto Zoom Auto Tilt

Target Retention Time

6

Figure Size Full Upper

Close

Custom

100

Tracking Start Position

Current Location

Character Position Left Middle

Right

Zone Setting Zone A
Save

Delete

Tracking Start Area Zone A

1. Zone Setting Zone Setting:Zone A, Zone B, Zone C, Zone D. Set area tracking must be set “from left to right”, and each area must have overlap. 2) Tracking Start Area
   18

4K UHD PTZ Camera

User Manual

Tracking Start Area:Zone A, Zone B, Zone C, Zone D.

7.5 Image Settings 7.5.1 Exposure

Exposure

Color

Image

Exposure Mode ExpCompMode
Backlight Anti-Flicker
Gain Limit Meter DRC

Auto Off Off 50Hz
Average 0

P/ T/ Z

Noise 9

Submit

Default

1. Exposure Mode Exposure Mode: Auto, Manual, SAE, AAE, Bright. 2) ExpCompMode ExpCompMode: On, Off. 3) Backlight Backlight: On, Off. 4) Anti-Flicker Anti- Flicker: Off,50Hz,60Hz. 5) Gain Limit Gain Limit: 0~15. 6) Meter Meter: Average, Center, Smart, Top. 7) DRC DRC: 0~8.

19

4K UHD PTZ Camera 7.5.2 Color

User Manual

Exposure

Color

Image

WB Mode Auto

RG Tuning BG Tuning

Saturation

Hue

Submit

P/ T/ Z

Noise

0 0 100% 7
Default

1. WB Mode WB Mode: Auto, Indoor, Outdoor, Manual, One Push, VAR. 2) RG Tuning RG Tuning: -10~10. 3) BG Tuning BG Tuning: -10~10. 4) Saturation Saturation: 60%~200%. 5) Hue Hue: 0~14.
   7.5.3 Image

2. Luminance Luminance: 0~14. 2) Contrast Contrast: 0~14. 3) Sharpness Sharpness: 0~11. 4) Flip-V Turn On/Off the Flip-V function. 5) Flip-H Turn On/Off the Flip-H function. 6) B&W-Mode B&W-Mode: On, Off. 7) Gamma Gamma: Default, 0.45, 0.48, 0.5, 0.56, PC. 8) Style Style: Default, Norm, Bright, PC.
   7.5.4PTZ

Exposure

Color

Image

P/T/Z

Noise

AF-Zone AF-Sense Image Freeze

Front High Off

Submit

Default

Exposure

Color

Image

P/T/Z

Luminance Contrast
Sharpness Flip-V Flip-H
B&W-Mode Gamma Style

On Off On Off Off Default Default

Noise
7 7 6

Submit

Default

1. AF-Zone AF-Zone: Top, Center, Bottom, Front. 2) AF-Sense AF-Sense: High, Normal, Low. 3) Image Freeze Image Freeze: On, Off.

20

4K UHD PTZ Camera 7.5.5 Noise

User Manual
7.7 System Settings 7.7.1 Initialize

Exposure

Color

Image

3DNR 6

P/ T/ Z

Noise

Submit

Default

3D NR: Off, 1~9. 7.6 Audio Settings

Audio Settings

Audio Switch On

Audio Type AAC

Sample Rate 48K

Bit Rate 96K

Input Type LINEIN

Input Vol 20

dB

ADTSOptions Off

Submit

Cancel

1. Audio Switch Turn On/Offthe audio switch. 2) Audio Type Audio Type: AAC. 3) Sample Rate Sample Rate: 44.1K, 48K. 4) Bit Rate Bit Rate: 96K, 128K. 5) Input Type Input Type: LINEIN, MIC. 6) Input Vol Select the volume value to control the channel volume. 7) ADTS Options Options: On/Off.

Reboot Factory Default

Reboot Factory Default

1. Reboot Click “Reboot” to restart system. 2) Factory Default Click the “Factory Default”, and the “Please press OK to reset the camera.” dialog box pops up. Select “OK” to restore the factory default.
   7.7.2 User

UserName Passwd Guest Passwd

admin guest

Submit

Cancel

Username and Password Modify the password of username and guest (only use letters and numbers).
7.7.3 U Disk Record

Record Settings
File Format MP4 Packed Time(min) 15
Save
USB Flash Disk Information
Capacity(M) 3846 Free Space(M) 300

Mount

Umount

Format

21

4K UHD PTZ Camera

User Manual

1. Record Settings Set up the File Format and Packed Time. 2) USB Flash Disk Information View the Capacity and Free Space of the USB Flash Disk.
   7.7.4Online Upgrade

7.8.2 Port

HTTP Port RTSP Port
TCP Port UDP Port Sony Visca

80 554 5678 1259 52381

Please Add Or Drag Files To This Area. Or Click Upload

Only Upload *.img Files

Update

The device supports online upgrade. If you need to upgrade the camera program, please refer to the upgrade interface instructions (as shown in the above figure), select the upgrade file package, and click the “Update” to upgrade the program.

7.8 Network Settings

7.8.1 Lan

IP Configuration Type IP Address
Subnet Mask Gateway
DNS Address MAC Address DHCP timeout Static fallback address Static fallback Subnet Mask

Fixed IP Address 192.168.100.88 255.255.255.0 192.168.100.1 8.8.8.8 D4:E0:8E:1E:20:20 30 sec 192.168.100.88 255.255.255.0

Submit

Cancel

The default camera IP: 192.168.100.88. The MAC address cannot be modified.

Submit

Cancel

Set the HTTP Port, RTSP Port, TCP Port, UDP Port and Sony Visca of the camera. A. HTTPPort The IP address identifies a network device and multiple network programs can run on the device, each network program uses the network port for data transmission. The port setting on this page is to set up which port the WEB SERVER program uses to transmit. During port mapping, it needs to be consistent with port number (default is 80). B. RTSP Port Set up the RTSP Port, default is 554. C. TCP Port Set up the TCP Port, default is 5678. D. UDP Port Set up the UDP Port, default is 1259. E. Sony Visca Set up the Sony Visca, default is 52381.
7.8.3 RTMP(S)

First Stream MRL
Second Stream MRL

On

Off

Video Audio

rt mp:/ / 192.168.100.138/ live/ st ream0

On

Off

Video Audio

rt mp:/ / 192.168.100.138/ live/ st ream1

Submit

Cancel

Set the MRL of RTMP(S) and select “On”, “Off”, “Video” and “Audio” functions to enable or disable video and audio in the
22

4K UHD PTZ Camera

User Manual

two streams. Click “Submit” and restart to take effect.

7.8.4

SRTSettings

SRT SRT Mode SRT Server SRT Port SRT Encryption SRT Password SRT Bandwidth Overhead SRT Variable Latency SRT StreamId

On

Off

Listener

192.168.100.1

4578

None

1234564913131

25

500

!::u=admin

Submit

Cancel

Turn On/Off SRT and set up the SRT Mode, SRT Server, SRT Port, SRT Encryption, SRT Password, SRT Bandwidth Overhead, SRT Variable Latency and SRT StreamID.
7.8.5 RTSP

RTSP Auth

On

Off

Submit

Cancel

Turn On/Off the RTSP Auth. 7.8.6ONVIF

ONVIF

On

Off

ONVIF Aut h

On

Off

Submit

Cancel

Turn On/Off the ONVIF and ONVIF Auth. 7.8.7 Multicast

Multicast Address Port

On

Off

224.1.2.3

6688

Submit

Cancel

Turn On/Off Multicast, set up Multicast Address (default is 224.1.2.3) and Port (default is 6688; 6688 is the multicast
23

4K UHD PTZ Camera

User Manual

port of the first stream and 6690 is the multicast port of the second stream).
7.8.8FreeD

FreeD Data Output(Beta) Destination IP Control Port

On

Off

192.168.100.99

19147

Data Port 19148

Submit

Cancel

Turn On/Off FreeD Data Output, set up the Destination IP,Control Port and Data Port.
7.8.9NTP

NTP Time Sync Time Zone
Server Address Time Interval(min)

On

Off

(GMT+08:00) Beijing, China

cn.ntp.org.cn

1440

Submit

Cancel

Turn On/Off NTP Time Sync, set up the Time Zone, Server Address (default is cn.ntp.org.cn) and Time Interval (default is 1440min).
7.9 Overlay

1. Stream Stream: First Stream, Second Stream. 2) Time Enable Enable or disable the Time. 3) Title Enable Enable or disable the Title. 4) Title Set up the Title of the display screen. 5) Title Horizontal Position Set up the Title Horizontal Position. 6) Title Vertical Position Set up the Title Vertical Position. 7) Time Horizontal Position Set up the Time Horizontal Position. 8) Time Vertical Position Set up the Time Vertical Position.
   7.10 Device Information

Information
Device ID UHDCamera Device Type F53.V Software Version SO C v2.0.19 -AR M 6.0.35S Webware Version v1.5.6

Submit

Cancel

Note
WEB interface and device information are subject to change without notice.

Stream First Stream

Time Enable Title Enable
Title

IP Camera

Title Horizontal Position –

0

Title Vertical Position –

0

Time Horizontal Position –

0

Time Vertical Position –

0

Submit

Cancel

8 AI Tracking
8.1 Web Control Speaker (Presenter)/Human Tracking By modifying web interface parameters, different close-up ratios can be obtained, and tracking can be set on/off, so as to display areas and character positions. If necessary, you can also choose whether to display tracking related prompt information.
24

4K UHD PTZ Camera

User Manual

The operation steps are as follows: Step 1 Enter the current IP address,
account, and password of the camera through the browser (see WEB Settings) to log in to the camera web interface.

Step 2 Enter the “Tracking” option, select speaker mode “Presenter”, and set the tracking parameters in the “Track Off” state.
Tracking Mode: Speaker (Presenter)/Area (Zone) The default is Presenter Mode.

25

4K UHD PTZ Camera

User Manual

Step 3 We can consider how long the Target Retention Time will take, with a default of 6 seconds and a maximum of 10 seconds.
Auto Zoom: Usually remains the default. When “Auto Zoom” is turned off, the camera lens can still move, but can only maintain the current magnification and cannot zoom. Auto Tilt: Usually remains default. When “Auto Tilt” is turned off, the camera lens can only move horizontally. Target Retention Time: can remain default. It is an important function to set how long it takes for the camera lens to return to the Home position or starting position after the tracking target is lost. The modification here takes effect immediately.
26

4K UHD PTZ Camera

User Manual

Step 4 Select the desired close-up effect. Figure Size By selecting different modes, users can customize the proportion of characters in the close-up screen, which is a very important feature. The modification here takes effect immediately. Full: The close-up image includes tracking the entire body of the target, as shown in the following figure.
27

4K UHD PTZ Camera

User Manual

Upper: The close-up image includes tracking the target above the knee, as shown in the following figure.
Close: The close-up image includes tracking the target above the waist, as shown in the following figure.
28

4K UHD PTZ Camera

User Manual

Custom: Adjust the tracking target proportion size.
Note
29

4K UHD PTZ Camera

User Manual

If the proportion set is large, the proportion of the tracking target in the camera screen will also increase. When the tracking target moves rapidly, the camera may not keep up.
Tracking Start Position The user can choose the position of the camera lens when starting and stopping tracking. Two Mode: Current Location/Preset 1 If you choose “Current Location”, the camera position when tracking is turned on is the current position; Similarly, the camera position when stopping tracking will also stop at the current position. If you choose “Preset 1”, you need to set an additional preset position for the camera. When tracking is turned on, the camera will first move to Preset 1. If someone enters the video screen at this time, the camera will automatically track. When the tracking target is lost (exceeding the timeout), the camera will automatically move to Preset 1.

Character Position Character Position: defaults to median. Left or right can be selected by oneself, and this function is mostly used for live streaming scenes.
30

4K UHD PTZ Camera

User Manual

Step 5 According to the requirements of the application scenario, you can choose whether to require “Humanoid frame” and “Tracking hint”, with default modes.
Used in live streaming scenarios, it is often not opened for temporary adjustments during live streaming.
31

4K UHD PTZ Camera

User Manual

Humanoid frame: Default/Off/Debug Default: After turning on tracking, if there are multiple people in front of the camera and pressing the direction key to select the tracking target, this box will automatically appear. After pressing the HOME key to confirm tracking, this box will disappear and the camera will start tracking. Off: When selecting a tracking target, the humanoid box is not displayed at all. This feature is suitable for live streaming scenarios. Debug: Turn on tracking, and the humanoid box will always appear on the tracking target. This feature is only applicable for debugging or demonstration.

Tracking hint: On/Off On: There will be a prompt in the upper left corner of the video during switch tracking. Off: There is no prompt in the upper left corner of the video during switch tracking. This function is also applicable to live streaming scenarios.

32

4K UHD PTZ Camera

User Manual

Step 6 Turn on tracking, press the arrow keys to select the tracking target, and then press Home to confirm.

Area Tracking (Zone) 33

4K UHD PTZ Camera

User Manual

Function: Divide the frequently active areas of the tracking target into several areas (A, B, C, D) as needed, and set corresponding preset positions and save them. When the tracking target enters this area, the camera will automatically call the preset position corresponding to the area to achieve tracking. Operation Method: Step 1 Enter the current IP address, account, and password of the camera through the
browser (see WEB Settings), you can log in to the camera web interface.

Step 2 Enter the “Tracking” page and select “Zone”. In the track off state, set the tracking parameters.

Step 3 Use the web interface’s directional keys and Zoom In/Out to adjust the lens position, and set multiple preset positions such as Zone A successively, and click “Save”.
The number of preset positions to be used in actual application scenarios can be considered by users themselves, but currently the maximum is 4. If the settings are incorrect, you can delete or reset them.
34

4K UHD PTZ Camera

User Manual

Tracking Start Area Tracking Start Area: You can select any Zone position as the tracking start or end position. When tracking is turned on, the camera will first move to this Zone position. If someone enters the video screen at this time, the camera will automatically track. When the tracking target is lost, the camera will automatically move to this Zone position.
35

4K UHD PTZ Camera

User Manual

8.2 Remote Control Speaker Tracking (Presenter) The camera default is Speaker Tracking (Presenter), which allows you to check the current settings from the web interface.
Function: This method can quickly achieve on/off tracking and select tracking targets. Single Person Scenario Press the F3 key on the remote control to start tracking, and press F4 key to exit tracking mode. When there is only one person in the scene, press the F3 key on the remote control to start tracking, and the camera will lock the target for direct tracking. The screen is
36

4K UHD PTZ Camera

User Manual

shown in the following figure, indicating that the tracking program has successfully started. Users can press F4 key to exit tracking mode.

Multi Person Scenario If there are multiple people in the scene, please first press the F3 key on the remote control to start tracking, if there are multiple people in front of the camera, you can press the left and right key on the remote control to select the target to track, and then press the HOME key to confirm. The camera will start tracking. Users can press F4 key to exit tracking mode.
37

4K UHD PTZ Camera

User Manual

9 Troubleshooting
Image The monitor shows no image 1) Ensure that the camera power supply is connected, the voltage is normal, and the
power indicator is always on. 2) Turn off the power switch to check that the camera is self-testing. 3) Ensure the cable of video platform and TV that in correct connection. Image jitters after the camera is properly connected 1) Ensure that the camerainstallation is in stable position. 2) Check that any vibrating machinery or object near the camera. There is no video image in browser That do not support IE browser and IE core browser, it is recommended to use Google, Firefox and Edge browsers. The camera video image will be displayed normally.
38

4K UHD PTZ Camera

User Manual

Unable to access camera through the browser 1) Using PC to access the network to test that the network access can work properly to
eliminate the network fault caused by cable and PC virus until the PC and camera can ping each other. 2) Disconnect the network, connect camera with PC separately and reset the IP address of PC if necessary. 3) Ensure that the IP address, subnet mask and gateway settings is correct. 4) Check that the MAC address is conflicts. 5) Check that the web port is modified, the default setting is 80. Forget the IP address or login password The default IP address is: 192.168.100.88; the default username and password are: admin. Control Remote control does not work 1) Check and replace with new batteries. 2) Ensure that the camera working mode is correct. 3) Ensure that the address key of remote control can match the camera. Serial port cannot control 1) Ensure that the protocol, address and bit rate of the camera are consistent. 2) Ensure that the control cable is properly connected.

39

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>