Olafus 3-LBC65M Smart Wireless Floodlight Camera User Manual
- August 15, 2024
- Olafus
Table of Contents
SMART WIRELESS
FLOODLIGHT CAMERA
Product Manual
COMPONENTS AND STRUCTURE
PARTS LIST
SPECIFICATIONS
LED Floodigh Camers
LED Floodlight Camera
Model| 3-LBC65M
Input Voltage| 100-240V 50/60Hz
Input Current| 0.6A
Rated Power| 55W
Luminous Flux| 55001m
CCT| 6500K
CR I| ai80
Power Factor| 2:0.9
L701350 lifetime| 30000hours L70Bso (4’25°
Beam Angle| 120°
rti| -20-40°C/-4°F-104LF
Luminaire Location| SUITABLE FOR WET LOCATIONS
Camera
Video| 4MP 25601440P
Field of View| 96° wide & 53° Height viewing angle
Tracking| Auto Tracking & Human Detection
Camera Angle| Pan & Tilt: 340° horizontal and 120° vertical rotation range
Audio| Two-Way Talk with Audio and advanced noise cancellation.
Internet Requirements| Recommended minimum upload speed of 2 Mbps per device.
Connectivity| 802.11 b/g/n/ac Wi-Fi connection @2.4/5GFIc
902-928 Mhz Radio
Storage| Micro SD Card up to 128GB (not included)
DIMENSIONS
Model| 3-LBC65M
Dimensions (LxHxW)| 274 x 242 x 147mm/ 10.79 x 9.52 x 5.79 in
Weight| 0.95kg/2.09 lb
SAFETY INFORMATION
WARNING: Risk of electrical shock
Disconnect power at the fuse or circuit breaker before installing.
Verify that the supply voltage is correct. Connect fixture to a
100-240V~50/60Hz power source.
Properly ground fixture.
Always follow code standards when installing wire connections.
If you are outside of North America, installation and wiring must be performed
by a licensed electrician.
CAUTION: Risk of fire
Do not install near combustible or flammable surfaces.
NOTICE
Do not connect this light fixture to a dimmer switch or timer. Floodlight
Camera must be installed on a wall and on a UL listed junction box.
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
DO NOT CONNECT THIS LIGHT FIXTURE TO AN UNGROUNDED ELECTRICAL SYSTEM. ATTACH
GROUND FIXTURE WIRE TO EITHER GREEN GROUND SCREW ON MOUNTING PLATE OR THE
GROUND WIRE IN THE OUTLET BOX.
CONNECTION PREPARATION
This HD Smart Wi-Fi Camera and App is compatible with the devices using iOS
9.0 and above with Wi-Fi option, or Android 5.0 and above with Wi-Fi option.
Please install the Floodlight Camera within Wi-Fi overed area to ensure the
best working performance.
Please see that your phone is connected to 2.4/5 GHz WiFi band of your router.
Please don’t use special characters, symbols to name the Wi-Fi and its
password.
PAIRING LED LIGHT WITH “Smart Life”
APP
Step 1. Get the App and the Account
https://smartapp.smart321.com/smartlife
- “Smart Life” App Download. There are 2 options for obtaining and downloading the “Smart Life” A on your smart device.
- Scan the QR code on the right. 2) Search for “Smart Life” in the App Store
or Google Play.
-
Enter the “Smart Life” App. Hegister an account and log in. It you already have an account for Smart Life App, Please select “Log in with existing account”.
Note: You will need your “Smart Life” App username and password to pair with Amazon Alexa and/or Google Assistant. -
Please turn on the Wi-Fi and Bluetooth before connecting LED lights to the “Smart Life” App.
PAIRING FLOODLIGHT CAMERA WITH “Smart Life” APP
Step 2. Connect the App
- Connect the floodlight camera to the power supply After power on, the light will be on for 1 second (It means the light can work normally). And then the light will turn off.
- Add the camera
- After the camera floodlight is powered on, wait for about 20-60s, the camera will say “Camera Starts”, which means the camera starts working. (If you don’t hear the prompt “camera starts for a long time. it’s because the camera is still initializing.)
- Wait for 10-155, the camera will rotate left, right, up, and down. Continue
waiting for another 10-155 until you hear the camera say “Please Configure
Network” and the blue indicator light will flash rapidly, which means you can
connect your cell phone to the camera.
Below is the location of the indicator light. Note: If the camera cannot be connected, follow these steps to reset the camera, and then pair your phone with the camera again.
Reset
- Press and hold the reset button for 5S-10S, and you will hear “Ding” sound. Then wait for 15-20s, and the camera will say “Camera Start”, which means the camera is starting to work.
- Wait for 10-15S, the camera will rotate left, right, up, and down. Continue waiting for another 10-155 until you hear the camera say “Please Configure Network” and the blue indicator light will flesh rapidly, which means you can connect your cell phone to the camera.
- There are two methods to add devices to the app.
Connection Method 1
1 Tap + button on top right comer and
tap “Add Device to add camera.
2 The APP will automatically search for the camera. After the camera appears, click “Add” to add the camera.
- Enter Wi-Fi password to join your network and click “next”
- Wait for the camera to register (about 20-30s). When the blue LED indicator
stop flashing and the camera will say “Camera online”, it means the connected
is finished. Tap “Done” to complete the light pairing.
Connection Method 2
1 Tap “+” button on top right corner and tap “Add Device” to add
camera.
(2) Tap “Camera&Lock” and then “Floodlight Camera” to enter next page.
(3) Tap the “Next” button to pair the LED Light.
(4) Enter Wi-Fi password to join your network and click “next”. - Put the QR code that appears on the APP in front of the camera at a
distance of 15-20cm(5.9-7.87in). When you hear a “Ding”, click on “I Heard a
Prompt”.
6 Wait for the device to register (about 20-30s). When the blue LED indicator stop flashing and The camera will say “Camera online”, It means the connected is finished.
7 Tap “Done” to complete the light pairing.
CAMERA LED INDICATOR
| NO. | LED Status | Camera Status |
|---|---|---|
| 1 | Blue indicator always on | The camera has been powered up. |
| 2 | Blue indicator flashing | Network pairing |
| 3 | Blue light off | The camera connects to the network successfully. |
Micro SD Card
-
To ensure Micro SD Card video recording works steady, we recommend to use a Class 10 or higher speed Micro SD Card.
-
To make sure the camera works normally, please format the Micro SD Card to FAT32 before the first time use.
-
Before insert or pull out the Micro SD Card, please power off the device.
Insert the Micro SD Card properly into the slot as below. -
It only support Micro SD Card up to 128GB (not included). Note: Micro SD Card (not included) will perform Event Recording or Non-Stop Recording. Upon reaching its maximum storage capacity, it will automatically record over the oldest recording. This will erase the oldest recording, and replace it with the new recording. For longer access to important recordings, it is recommended to move the recordings from the Micro SD card to your computer etc. Recorded videos can be seen under the Playback icon.
HOW TO OPERATE THE APP
Playback| You can watch back the previous video recordings here. Note: Micro
SD Card is required to watch back.
---|---
Gallery| Check manual screenshots and recorded videos
Theme Color| Change the color of the APP interface
Private Mode| Turn off the camera image
Night Mode
Select ON, the camera screen is black and white
Select Off, the camera screen is in color
Select Auto, the camera will adjust the color of the screen according to the
environment.
The camera will adjust the color of the screen according to the brightness of
the environment, it may be color or black and white. Motion Tracking
Click to start motion tracking – the camera will follow the person, if there
is no continuous movement after 1 minute, the camera will return to the
original position. Motion Detection
Start motion monitoring, when the camera detects the movement of an object, it
will alert you via a message. Detection Alarm Settings
You can set detection alarms by following these steps
Light Control
Manual Setting
Click on Light, then you can control the light on/off, brightness, and timing.
Motion Trigger: When it is night time and the camera detects a moving object
(such as a person or a car), the light will turn on for 30 seconds and then
turn off.
The angle of the camera can be manually adjusted. One-way/two-way
communication mode settingsTurning message notifications off
and on. Disable pushing of motion monitoring notifications
If you want to activate the motion monitoring function, but do not want to frequently receive notifications, you can disable the notification push feature.
Share the device
You can choose to share the device to
other members of the family.
Note: Shared family members can only view monitoring and notifications, but cannot set up the monitor.
Remove the device
When you replace your phone, or someone
else wants to connect to the device, be sure to remove the device from your
old phone first.
Note: For security reasons, the device can only be connected by one person at a time. If someone else wants to see the camera information at the same time, you can refer to “Share the device
HOW TO CONNECT WITH ALEXA SHOW AND GOOGLE ASSISTANT APP Tap “Me” and find the third-party voice device you want to connect to and tap it, then follow the steps to connect.
SHUT POWER OFF AT THE BREAKER
Turn off power to work area at main circuit breaker of fuse box
Caution: Please make sure your wall switch and power at main circuit breaker both off. If you don’t know where your breaker is or how to turn off power to your floodlight circuit, consult with a licensed electrician.
PREPARATION
NOTE:
Before beginning assembly of product, make sure all parts are present. Compare parts with parts list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 30-60 minutes.
Recommended to be installed 2.5m (8.2ft) above the ground but not higher than 5m (16.4ft).
Product appearance may vary from image shown.
TOOLS REQUIRED (not included
PROPER INSTALLATION
HEIGHT
The proper installation height to optimize the motion sensor performance is around 2.5m (8.2ft)
INSTALLATION STEPS
FOR WET LOCATION, MAKE SURE FILL FULL THE GAP OF EVA GASKET AND MOUNTING
SURFACE WITH SEALING COMPOUND OR SILICONE GLUE.
Note:
If the camera falls off accidentally, reinstall the camera as follows.
RESTORE POWER AT THE BREAKER After restoring power, the lights
will turn on and your Floodlight Camera will begin speaking to you to let you
know it’s in setup mode.
FCC ID: 2AT7E-3-LBC65M
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules, Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is
connected. -Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FAQ
1. What if I can't connect to the camera?
Try to reset the camera; The reset step is refer to page 7-9th. If it still can not be solve, contact our seller and provide the number posted on the camera, please.
2. Can't find an Micro SD Card?
Firstly we suggest using these famous brands card, like Samsung, SanDisk, Kingston etc. with at least class 10. Secondly, please format it to FAT32, which is the only format that camera can support.
3. Two way audio is not working?
4. You cannot get the video for a long time?
Please first make sure the camera is installed as close as possible to your router. It is not recommended to install the camera in a place where there are two thick walls away from the router. Please test your network and make sure it works well.
For more questions, please send them via the “Settings” – “FAQ&Feedback” within the app.
HK JW Illumination Co., Limited
Unit 616, 6/F., Kam Teem Industrial Building. 135 Connaught Road West, Sai Wan
Hong Kong
Manufacturer/Hersteller: MDH LIGHTING LTD Suite 302, 292 Strovolos Avenue,
2048 Strovolos Nicosia, Cyprus
UK Importer: MDH LIGHTING LTD 69 Aberdeen Avenue, Cambridge CB2 8DL, United
Kingdom
Made in China
support@olafuslife.com
www.olafuslife.com