Olafus LEB50E LED Work Light User Manual
- June 5, 2024
- Olafus
Table of Contents
LED WORK LIGHT
Product Manual
MODEL: LEB50E
COMPONENTS AND STRUCTURE
PARTS LIST
SPECIFICATIONS
LED WORK LIGHT
Model| LEB50E
Input Voltage| 100-240V ~50/60Hz
Input Current| 0.55A
Rated Power| 50W
Luminous Flux| 4500lm
CCT| 2700-6500K
CRI| ≥80
Power Factor| ≥0.9
L70B50 lifetime| 30000hours L70B50@25°
Beam Angle| 120°
ta| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR WET LOCATIONS
DIMENSIONS
Model | LEB50E |
---|---|
Dimensions(LxHxW) | 260x315x183mm/10.23×12.4×7.20 in |
Weight | 1.79 kg / 3.94 lb |
PAIRING LED LIGHT WITH THE “SMART LIFE” APP
NOTE:
Turn ON/OFF the Smart LED Light three times until the LED Light starts to flash
quickly, which indicates the success of the factory reset.
Step 1: “SMART LIFE” App Download. There are 2 options for obtaining and
downloading the “SMART LIFE” App on your smart device.
- Scan the QR code on the right.
- Search for “SMART LIFE” in the App Store or Google Play.
https://smartapp.tuya.com/smartlife
Step 2: Enter the “SMART LIFE” App. and register an account and log in. If you already have an account for the SMART LIFE App., Please select “Log in with existing account”.
Step 3: Please turn on the Wi-Fi and Bluetooth before connecting LED lights to
the “SMART LIFE” APP.
Tap the “+” button on top right corner to add a device, then tap”lighting
device” to enter the next page.
Step 4 : How to pair the LED Light
-
Power up the LED light.
-
Quickly turn the light off and on 3 times until it flashes or breathes.
-
Tap “Next” to enter the pairing step.
-
Tap “+” to add the LED light.
-
Tap “Next” to complete the light pairing.
-
You can tap ” ” to change the device name.
-
Tap “Done” to enter the control panel.
HOW TO OPERATE THE APP
Here you can choose the color of the light and adjust the brightness.| Here
you can choose different lighting modes.
Here you can choose the sound/ voice control mode.| Here you can set schedules for the light or apply other functions.
PREPARATION
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED. RISK OF SHOCK- BEFORE BEGINNING INSTALLATION,TURN
OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT THE MAIN CIRCUIT BREAKER BOTH
ARE OFF. IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED
ELECTRICIAN. WARNING: INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM
MAY CAUSE THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE
CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE,
ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN
INJURY OR DEATH. BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULATION
(COVERING) DURING INSTALLATION. DO NOT LET THE WIRES TOUCH ANY SHARP EDGES.
INSTALLATION STEPS
Check all components for damage, do not use the product if it is damaged. Product appearance may vary from the image shown.
STEP 1:
Put the bracket onto the prepared mounting hole and then screw it on.
STEP 2:
Unbind the wire and put the plug into the socket; Press the ON/OFF button and
then the LED work light works.
FCC 0:2AT7E-LEB50E
FCC Warning:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. Note: This equipment has been
tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body.
Manufacturer/Hersteller:
Shen Zhen Shi Zhi Hui Duo Ke Ji You Xian Gong Si
Qian wan Yi lu 1 hao A dong 201 shi, qian hai shen gang he Zuo Qu, shen
Zhen, Guang Dong, 518000, CN
support@olafuslife.com
www.olafuslife.com
MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus | support@olafuslife.com
MDH LIGHTING
LTD
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom | support@olafuslife.com
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>